AJAX GlassProtect Manuel utilisateur
GlassProtect User manual
Updated October 18, 2019
GlassProtect is a wireless detector detecting glass break at a distance up
to 9 meters. It is used inside premises, can operate up to 7 years from a
pre-installed battery and is furnished with a socket for connecting an
additional detector.
GlassProtect operates within the Ajax security system, by connecting via
the protected Jeweller protocol to the hub. Communication range – up to
1,000 m, absent any obstacles. In addition, the detector can be used as
part of third-party security central units due to the uartBridge or ocBridge
Plus integration module.
The detector is set up via a mobile application for iOS and Android-based
smartphones. The user is notified of all events through push notifications,
SMS messages and calls (if activated).
The Ajax security system is self-sustaining, but the user can connect it to
the central monitoring station of a private security company.
Buy breakage detector GlassProtect
Functional elements
1. Light indicator
2. Microphone hole
3. SmartBracket attachment panel (perforated part is required for actuating
the tamper in case of any attempt to tear off the detector from the surface.
Don’t break it off!)
4. External detector connection socket
5. QR code
6. Device switch
7. Tamper button
GlassProtect Operating Principle
GlassProtect is furnished with a sensitive electret microphone and set up to
detect the distinctive sound of broken glass, consisting of a low-frequency
hit and high-frequency tinkle of chips. Due to the two-stage glass break
detection, the risk of false actuation is minimal.
GlassProtect detector will not react to breaking if a film has been applied the glass: shockproof,
sunscreen, decorative or other. In order to detect the breaking of this type glass, we recommend
using a DoorProtect Plus wireless opening detector with shock and tilt sensor.
After actuation, the GlassProtect detector set in the intrusion detection
mode immediately transmits an alarm signal to the hub, activating
the sirens connected to the hub and notifying the user and private security
company.
Connecting the Detector to the Ajax
Security System
Detector Connection to hub
Before starting connection:
1. Following the hub instruction recommendations, install the Ajax
application on your smartphone. Create an account, add the hub to the
application, and create at least one room.
2. Go to the Ajax application.
3. Switch on the hub and check the internet connection (via Ethernet cable
and/or GSM network).
4. Ensure that the hub is disarmed and does not start updates by checking its
status in the mobile application.
Only users with administrative privileges can add the device to the hub
How to connect the GlassProtect to the hub:
1. Select the Add Device option in the Ajax application.
2. Name the device, scan/write manually the QR Code (located on the body
and packaging), and select the location room.
3. Select Add — the countdown will begin.Switch on the device.
For the detection and interfacing to occur, the detector should be located
within the coverage area of the wireless network of the hub (at a single
protected object).
Request for connection to the hub is transmitted for a short time at the time
of switching on the device.
If the connection to the Ajax hub failed (LED blinks once per second),
switch off the detector for 5 seconds and repeat the attempt. The detector
connected to the hub will appear in the list of devices of the hub in the
application. Update of the detector statuses in the list depends on the
device inquiry time set in the hub settings, with the default value – 36
seconds.
Connecting the Detector to Third Party Security Systems
To connect the detector to a third party security central unit using
the uartBridge or ocBridge Plus integration module, follow the
recommendations in the manual of the respective device.
States
1. Devices
2. GlassProtect
Parameter Value
Temperature Temperature of the Detector. Measured on the
processor and changes gradually
Signal Strength Signal strength between the hub and the
detector
Battery Charge Battery level of the detector, displayed in
increments of 25%
Lid The tamper mode of the detector, which reacts
to the detachment of or damage to the body
Delay when entering, sec Delay time when entering. The option is
available only with a connected wired detector.
Delay when leaving, sec Delay time when exiting. The option is
available only with a connected wired detector.
Connection Connection status between the hub and the
detector
Sensitivity Sensitivity level of the sensor
Secondary detector Status of the external detector connected to
GlassProtect
Always Active If active, the detector is always in the armed
mode
Firmware Detector firmware version
Device ID Device identifier
Setting Up the Detector
1. Devices
2. GlassProtect
3. Settings
Setting Value
First field Detector name, can be edited
Room Selecting the virtual room to which the device is assigned
Sensitivity
Choosing the sensitivity level of glass break detector:
High
Normal
Low
External contact enabled If active, the detector registers external detector alarms
Always active If active, the detector always registers glass breakage
Delay when entering, sec Selecting delay time when entering. The option is available only
with a connected wired detector.
Delay when leaving, sec Selecting delay time on exit. The option is available only with a
connected wired detector.
Delays in night mode Delay turned on when using night mode
Arm in night mode If active, the detector will switch to armed mode when using
night mode
Alert with a siren if glass break
detected
If active, HomeSiren and StreetSiren are activated when the
glass break detected
Activate the siren if an additional
contact is open
If active, HomeSiren and StreetSiren are activated during an
external detector alarm
Signal Strength Test Switches the detector to the signal strength test mode
Detection Zone Test Switches the detector to the detection area test
Attenuation Test Switches the detector to the signal fade test mode (available in
detectors with firmware version 3.50 and later)
User Guide Opens the detector User Guide
Unpair Device Disconnects the detector from the hub and deletes its settings
Indication
Event Indication Note
Turning on the detector Lights up green for about one second
Detector connection to
the hub, ocBridge and uartBridge Lights up continuously for a few seconds
Alarm / tamper activation Lights up green for about one second Alarm is sent once in 5
seconds
Battery needs replacing During the alarm, it slowly lights up
green and slowly goes out
Replacement of the
detector battery is
described in the Battery
Replacement paragraph
Functionality testing
The Ajax security system allows conducting tests for checking the
functionality of connected devices.
The tests do not start straight away but within a period of 36 seconds when
using the standard settings. The test time start depends on the settings of
the detector scanning period (the paragraph on “Jeweller” settings in hub
settings).
Signal Strength Test
Detection Zone Test
Attenuation Test
Autres manuels pour GlassProtect
8
Table des matières
Autres manuels AJAX Capteur de sécurité
AJAX
AJAX DoorProtect Manuel utilisateur
AJAX
AJAX MotionProtect Manuel utilisateur
AJAX
AJAX FireProtect 2 Heat/CO Jeweller Manuel utilisateur
AJAX
AJAX DoorProtect Plus Manuel utilisateur
AJAX
AJAX ReX Manuel utilisateur
AJAX
AJAX MotionProtect Manuel utilisateur
AJAX
AJAX LifeQuality Jeweller Manuel utilisateur
AJAX
AJAX MotionProtect Curtain Manuel utilisateur
AJAX
AJAX DoorProtect Manuel utilisateur
AJAX
AJAX FireProtect Manuel utilisateur
AJAX
AJAX MotionProtect Plus Fibra Manuel utilisateur
AJAX
AJAX MotionProtect Manuel utilisateur
AJAX
AJAX LeaksProtect Manuel utilisateur
AJAX
AJAX GlassProtect Manuel utilisateur
AJAX
AJAX DoorProtect Manuel utilisateur
AJAX
AJAX GlassProtect Fibra Manuel utilisateur
AJAX
AJAX GlassProtect Manuel utilisateur
AJAX
AJAX DoorProtect Plus Manuel utilisateur
AJAX
AJAX MotionProtect Manuel utilisateur
AJAX
AJAX MotionCam Fibra Manuel utilisateur
