AJAX FireProtect Manuel utilisateur

FireProtect / FireProtect Plus User Manual

Updated October 4, 2021

FireProtect (FireProtect Plus) is a wireless indoor re detector with an in-built

buzzer and a battery, ensuring up to 4 years of autonomous operation. FireProtect

can detect smoke and rapid temperature increase.

Aside from these functions, FireProtect Plus additionally can alert of dangerous

CO level. Both detectors can function independently from the hub.

Connecting to the Ajax security system via a secured radio protocol,

FireProtect (FireProtect Plus) communicates with the at a distance of up to

1,300 m in line of sight.

The detector can be a part of third-party security systems, connecting to them via

the or integration module.

Jeweller

hub

Ajax uartBridge Ajax ocBridge Plus

Buy �re detector with carbon monoxide sensor FireProtect Plus

The detector is set up via the for iOS, Android, macOS, and Windows.

The system noties the user of all events through push notications, SMS, and

calls (if activated).

The Ajax security system can be connected to a central monitoring station of a

security company.

Functional Elements

Operating Principle

Ajax apps

Buy �re detector FireProtect

1. Siren hole

2. Light indicator (acts as the sensor and Test button)

3. Smoke chamber hole with the temperature detector behind the net

4. SmartBracket attachment panel

5. Power button

6. Tamper button

7. QR code

When smoke penetrates the detector chamber, it distorts infrared light between the

emitter and photoelectric receiver. This distortion triggers a smoke alarm. When

the temperature exceeds 60°or rises by 30°during 30 minutes (not necessary to

reach 60°), the detector registers temperature increase, which triggers a re

alarm.

The life span of the FireProtect Plus detector lasts up to 7 years (up to 10 years for the

). In the event of a detector failure, you will receive a corresponding noti�cation —

it will need to be replaced or submitted for .

FireProtect Plus has an additional sensor to detect a dangerous CO level. If the

concentration of CO in the air exceeds a certain level, the detector generates an

alarm.

The detector is triggered:

In case of alarm, the detector activates the built-in buzzer (the siren sound can be

heard from afar) and blinks with the light indicator. When connected to a security

system, both the user and the security company are notied of the alarm.

The siren of the device can be turned off using three ways:

FireProtect

comprehensive diagnostics

• within 60–90 min at carbon oxide concentration 50 ppm / 0.005%

• within 10–40 min at CO concentration 100 ppm / 0.01%

• within 3 min at carbon oxide concentration 300 ppm / 0.03%.

1. By pressing the Ajax logo on the device lid (there is a touch button under the

logo).

2. Through the Ajax app. In case of re alarm, you will see a pop-up message in

Ajax app suggesting to turn off the built-in sirens.

3. Using the / (if Interconnected FireProtect Alarms feature

is enabled). To turn off the built-in sirens in case of re alarm, press the “*”

button on the KeyPad/KeyPad Plus.

KeyPad KeyPad Plus

Fire Alarmcommand for this button in the KeyPad/KeyPad Plus settings.

If smoke and/or temperature levels do not restore to normal values, in 10 minutes,

the FireProtect/FireProtect Plus turns on the siren again.

Connecting the Detector to the Ajax Security System

Connecting to the hub

Before starting connection:

Only users with administrator rights can add the device to the hub

Pairing the detector with hub:

1. Following the hub user guide, install the . Create the account, add the

hub, and create at least one room.

Ajax app

2. Switch on the hub and check the internet connection (via Ethernet cable and/or

GSM network).

3. Make sure that the hub is disarmed and does not update by checking its status

in the Ajax app.

1. Select Add Device in the Ajax app.

2. Name the device, scan or type the QR Code (located on the detector body and

packaging), and select the location room.

To make sure that the detector is on, press the on/off button — the logo will light up

red for a second.

For detection and pairing to occur, the detector should be located within the

coverage area of the wireless network of the hub (at a single protected object). The

connection request is transmitted for a short time: at the moment of switching on

the device.

If pairing with the hub fails, the detector operates autonomously; switch off the

3. Tap Add — the countdown will start.

4. Switch on the device.

Connecting to Third Party Security Systems

To connect the detector to a third party security central unit using the

or integration module, follow the recommendations

in the manual of the respective device.

The smoke detector always operates in the active mode. When connecting

FireProtect to third party security systems, it is appropriate to place it in a

permanently active protection zone.

States

Parameter State

Temperature Temperature of the device. Measures on the

device processor and changes gradually

Jeweller Signal Strength Signal strength between the hub and the detector

Connection Connection status between the hub and the

device

Battery Charge

Battery level of the device. Two states available:

Ajax

uartBridge Ajax ocBridge Plus

1. Devices

2. FireProtect | FireProtect Plus

• ОК

• Battery discharged

How battery charge is displayed in

Ajax apps

Temperature Threshold Exceeded The state of temperature threshold exceeded

alarm

Rapid Temperature Rise The state of rapid temperature increase alarm

High CO Level (FireProtect Plus only) The state of dangerous CO level alarm

Backup Battery Charge Backup battery level of the device

Smoke sensor The state of the smoke detector

Smoke Sensor Dust Level The dust level in the smoke chamber

Temporary Deactivation

Shows the status of the device: active, completely

disabled by the user, or only noti�cations about

triggering of the device tamper button are

disabled

Firmware Detector �rmware version

Device ID Device identi�er

Settings

Setting Value

First �eld Device name, can be edited

Room Selecting the virtual room to which the device is

assigned

Dangerous CO Level Alarm (FireProtect Plus only)If active, the detector alerts of exceeding the

limits of carbon monoxide concentration

1. Devices

2. FireProtect | FireProtect Plus

3. Settings

Alert with a siren if temperature threshold

exceeded

If active, added to the systemare

activated in case if temperature threshold

exceeded

Alert with a siren if rapid temperature rise

detected

If active, added to the systemare

activated in case if rapid temperature rise

detected

Alert with a siren if CO detected (FireProtect Plus

only)

If active, added to the systemare

activated in case if CO concentration is

dangerous

Jeweller Signal Strength Test Switches the device to the signal strength test

mode

FireProtect Self Test Starts FireProtect selftest

Temporary Deactivation

Allows the user to disconnect the device without

removing it from the system.

Two options are available:

Note that a disabled device does not trigger an

interconnected alarm of �re detectors. But if

smoke is detected, the built-in siren will sound

User Guide Opens the detector User Guide

sirens

• Entirely— the device will not execute system

commands or participate in automation

scenarios, and the system will ignore device

alarms and other noti�cations

• Lid only— the system will ignore only

noti�cations about the triggering of the device

tamper button

Learn more about temporary

deactivation of devices

the Jeweller settings.

To enable Interconnected Alarms:

1. Open the Devices tab in the

2. Select a hub

3. Go to its Settings by pressing

4. Select the Service item

5. Go to the Fire detectors settings menu and activate the Interconnected

FireProtect Alarms option

Interconnected alarms are supported by FireProtect and FireProtect Plus detectors with

�rmware versions 3.42 and later. Please note that when you turn on the interconnected

alarms, you cannot set the hub–detector ping interval (Jeweller settings) of more than 48

seconds.

6. If necessary, set the Delay of Interconnected Alarms from 0 to 5 minutes (in

1-minute increments). The option allows you to postpone the interconnected alarm

for a specied period of time.

When this option is inactive, the interconnected alarm is sent to all �re detectors within a

minute.

The function works as follows:

1. One of the FireProtect/FireProtect Plus detectors detects an alarm.

2. Delay of Interconnected Alarms starts.

3. The built-in siren of the re detector informs the alarm. Users receive

Ajax app

Autres manuels pour FireProtect

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels AJAX Capteur de sécurité

AJAX

AJAX DoorProtect Manuel utilisateur

AJAX

AJAX FireProtect 2 Jeweller Manuel utilisateur

AJAX

AJAX FireProtect 2 Heat/CO Jeweller Manuel utilisateur

AJAX

AJAX LeaksProtect Manuel utilisateur

AJAX

AJAX HomeSiren Manuel utilisateur

AJAX

AJAX MotionCam Manuel utilisateur

AJAX

AJAX LeaksProtect Manuel utilisateur

AJAX

AJAX DoorProtect Plus Manuel utilisateur

AJAX

AJAX LeaksProtect Manuel utilisateur

AJAX

AJAX FireProtect 2 Jeweller Manuel utilisateur

AJAX

AJAX GlassProtect Manuel utilisateur

AJAX

AJAX MotionCam Fibra Manuel utilisateur

AJAX

AJAX MotionProtect Manuel utilisateur

AJAX

AJAX LifeQuality Jeweller Manuel utilisateur

AJAX

AJAX GlassProtect Manuel utilisateur

AJAX

AJAX GlassProtect Manuel utilisateur

AJAX

AJAX FireProtect Manuel utilisateur

AJAX

AJAX DoorProtect Manuel utilisateur

AJAX

AJAX MotionProtect Fibra Manuel utilisateur

AJAX

AJAX GlassProtect Fibra Manuel utilisateur

AJAX

AJAX FireProtect 2 (Heat) Jeweller Manuel utilisateur

AJAX

AJAX LeaksProtect Manuel utilisateur

AJAX

AJAX GlassProtect Manuel utilisateur

AJAX

AJAX MotionProtect Manuel utilisateur

Manuels Capteur de sécurité populaires d'autres marques

THORLABS

THORLABS PDA10JT Manuel utilisateur

Waeco

Waeco UV-DETECT Manuel utilisateur

Intermatic

Intermatic IOS-DSIMF Manuel utilisateur

urmet domus

urmet domus 1083 Manuel utilisateur

Siemens

Siemens AZL66 Series Manuel utilisateur

BTI

BTI Profiline Multi Finder Manuel utilisateur

Challenger

Challenger SL01 Manuel utilisateur

DMP Electronics

DMP Electronics 1122INT Manuel utilisateur

Rielta

Rielta Ladoga MK-RK Manuel utilisateur

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuel utilisateur

Bosch

Bosch DS835 Manuel utilisateur

DBI SALA

DBI SALA EZ Stop Manuel de l'opérateur

Lamptime

Lamptime ST05C Manuel utilisateur

Ubiquiti

Ubiquiti MFI-MSC Manuel utilisateur

Subsite

Subsite 910R Instructions d'installation

Satel

Satel OPAL Pro Manuel utilisateur

Aleph

Aleph XC-1XTEU Manuel utilisateur

Pima

Pima LARIS QUAD Manuel utilisateur