AJAX MotionProtect Jeweller Manuel utilisateur

MotionProtect Jeweller User Manual

Updated July 30, 2022

MotionProtect Jeweller is a wireless indoor motion detector. It can operate for

up to 5 years from a built-in battery, and monitors the area within a 12-meter

radius. MotionProtect ignores animals, while recognizing a human from the rst

step.

MotionProtect operates within the Ajax security system, connected to the

via the protected protocol. The communication range is up to 1700

meters in the line of sight. In addition, the detector can be used as a part of

third-party security central units via the or integration

modules.

The detector is set up via the for iOS, Android, macOS and Windows.

The system noties users of all events through push notications, SMS and

calls (if activated).

Functional Elements

hub

Jeweller

uartBridge ocBridge Plus

Ajax app

Buy MotionProtect Jeweller

Operating Principle

1. LED indicator.

2. Motion detector lens.

3. SmartBracket mounting panel. To remove the panel, slide it down.

4. Perforated part of the mounting panel. Necessary to trigger a tamper in

case of any attempt to detach the detector from the surface. Do not break it

off.

5. . Triggers when an attempt is made to detach the detector

from the surface or remove it from the mounting panel.

Tamper button

6. Device switch.

7. Detector QR code. Is used to connect the device to the Ajax security system.

00:00

00:12

MotionProtect Jeweller is a wireless motion detector. The detector can identify

intrusions by detecting moving objects with temperatures close to the human

body using IR sensors.

When an armed detector identies motion, it instantly sends an alarm to the

hub, activating the sirens connected to the system, triggering scenarios, and

notifying users and the security company. All MotionProtect alarms and events

are recorded in the event feed of the Ajax apps.

Users know where motion is detected. The notications contain the name of the

hub (protected facility), the name of the device, and the virtual room to which

the detector is assigned.

The detector doesn’t arm instantly. The time it takes to switch to armed mode depends

on exit delays (specied in the detector settings) and the hub–detector polling interval

(Jeweller or Jeweller/Fibra settings, the default value is 36 seconds). In the rst case,

the delay is set by an administrator or a PRO-user with administrator rights. In the

second case, the delay occurs because the hub takes one ping interval to notify the

detector about the transition to armed mode.

Pet immunity

When properly installed and congured, MotionProtect does not react to

animals up to 50 centimetres tall and weighing up to 20 kilograms.

How Ajax noties users of alerts

More about Ajax motion detectors

The detector must be installed at 2.4 meters without obstruction to its view. For

example, in a corner where the view will not be blocked by a closet or other

furniture on which a pet can climb.

It is also important to set the proper sensitivity in the :

When indoor motion detectors are installed below the recommended height,

animals move in the hypersensitive zone. The detector can raise the alarm if a

shepherd walks on its hind legs or even a tiny spaniel plays on a chair. The

detector will also raise the alarm if the animal can jump to the level of

MotionProtect or move near it.

Temperature compensation

The detector perceives people and other objects as heat spots. The device

monitors these heat spots and, if they move, detects an alarm. MotionProtect

reacts to the movement of heat spots whose temperature is close to the human

body.

detector settings

High — the detector does not react to cats (up to 25 cm tall).

Medium — it does not react to small dogs (up to 35 cm tall).

Low — it does not react to animals up to 50 cm tall.

Why detectors react to animals and how to avoid this

How to install MotionProtect correctly

When the ambient temperature is about the temperature of the human body, the

correct operation of the detector is not guaranteed unless temperature

compensation is applied. It is used in all Ajax motion detectors. MotionProtect

recognizes motion across the entire operating temperature range with

temperature compensation.

Sending events to the monitoring station

The Ajax security system can transmit alarms to the monitoring

app as well as the central monitoring station (CMS) in the formats of the Sur-

Gard protocol (Contact ID), SIA (DC-09), ADMECO 685, and other proprietary

protocols. A complete list of supported protocols is .

MotionProtect can transmit the following events:

When an alarm is received, the security company monitoring station operator

knows what happened and precisely where to send a fast response team on the

site. The addressability of Ajax devices allows sending events to the PRO

Desktop or the CMS the type of the device, its name, security group, and virtual

room. Note that the list of transmitted parameters may differ depending on the

kind of CMS and the selected protocol for communication with the monitoring

station.

The device ID and the loop (zone) number can be found in .

Learn more

PRO Desktop

available by the link

Which CMSs can the Ajax security system be connected to

1. Motion alarm.

2. Tamper alarm / restoration.

3. Loss / restoration of connection with the hub or radio signal range extender.

4. Temporary deactivation / activation of the detector.

5. Unsuccessful attempt to arm the security system (when

is enabled).

System Integrity

Check

device states in the Ajax app

Connecting to the security system

Before adding a device

Connecting to the hub

1. Install an .Ajax app

2. if you don’t have one. Add a compatible hub to the app,

make the necessary settings, and create at least one virtual room.

Create an account

3. Ensure that the hub is switched on and has Internet access via Ethernet, Wi-

Fi and/or mobile network. You can check the connection state in the Ajax

app or by looking at the hub LED indicator. It should light up white or green.

4. Ensure that the hub is disarmed and does not start updates by checking its

status in the Ajax app.

1. Open the Ajax app. If you have access to multiple hubs or using the PRO

app, select the hub where you want to add the detector.

2. Go to the Devices tab and click Add Device.

3. Name the detector, scan or type in the QR code (placed on the detector and

the package box), and select a room and a group (if is

enabled).

Group mode

4. Press Add.

5. Switch on the device.

If the connection fails, turn the detector off and try again in 5 seconds. Note that

if the maximum number of devices has already been added to the hub

( ), you will be notied when you try to add a new

one.

To connect MotionProtect to the hub, the detector must be located at the same

facility as the system (within the hub radio signal range). For the detector to

work via the radio signal range extender, you need rst add the detector and

range extender to the hub, then connect it to the range extender.

The detector connected to the hub will appear in the list of hub devices in the

Ajax app. Updating the statuses of devices in the list depends on the Jeweller or

Jeweller/Fibra settings; the default value is 36 seconds.

The hub and the device operating at different radio frequencies are incompatible. The

radio-frequency range of the device may vary by region. We recommend purchasing and

using Ajax devices in the same region. You can check the range of operating radio

frequencies with the

MotionProtect works with one hub. When connected to a new hub, the detector

stops sending events to the old one. When added to a new hub, the detector is

not removed from the device list of the old hub. This must be done through the

Ajax app.

Connecting to third party security systems

To connect the detector to a third party security central unit with the

or integration module, follow the recommendations in the

manuals of these devices.

depending on the hub model

technical support service

uartBridge

ocBridge Plus

Malfunctions

When a malfunction is detected (for example, there is no connection via

Jeweller), the Ajax app displays a malfunction counter on the device icon. All

malfunctions are shown in the detector states. Fields with malfunctions will be

highlighted in red.

A malfunction is displayed if:

Icons

The icons display some of the MotionProtect states. You can view them in the

Ajax app in the Devices tab.To access them:

Icon Meaning

Jeweller signal strength. Displays the signal strength between the detector and

hub or range extender. The recommended value is 2 or 3 bars.

The detector battery charge level.

The detector is operating via a .

The detector operates in the Always active mode.

The detector temperature is out of acceptable limits: below –10°C and

above +40°C.

The detector enclosure is open (tamper is triggered).

No connection with the hub or radio signal range extender via Jeweller.

The detector battery is low.

1. Sign in to the .Ajax app

2. Select the hub if you have several of them or using a PRO app.

3. Go to the Devices tab.

Learn more

radio signal range extender

Entry delay is enabled.

Exit delay is enabled.

MotionProtect will arm in Night mode.

MotionProtect has detected motion. The icon is displayed when the detector is

armed

MotionProtect is temporarily disabled.

MotionProtect has been deactivated due to exceeding the preset number of

alarms.

MotionProtect has tamper triggering events temporarily deactivated.

States

The states include information about the device and its operating parameters.

The states of MotionProtect can be found in the Ajax app:

Parameter Value

Learn more

1. Go to the Devices tab.

2. Select MotionProtect from the list.

Temperature Detector temperature. It is measured on the

processor and changes gradually.

The acceptable measurement error between the

value in the app and the ambient temperature is

2°C.

The value is updated as soon as the detector

identies a temperature change of at least 1°C.

Jeweller Signal Strength

Signal strength between the detector and hub or

range extender on the Jeweller channel. The

recommended value is 2 or 3 bars.

Jeweller is a protocol for transmitting

MotionProtect events and alarms.

Battery Charge

Battery level of the device. Displayed as a

percentage.

When the batteries are low, the Ajax apps and

the security company will receive appropriate

notications.

After sending a low battery notication, the

detector can work for up to 2 months.

Lid

The status of the detector tamper that responds

to detachment or opening of the device

enclosure:

Delay When Entering, sec Delay time when entering: from 5 to 120

seconds.

How the battery charge is displayed

Battery life calculator

Open — the detector was removed from the

SmartBracket, or detector integrity was

compromised. Check the device.

Closed — the detector is installed on the

SmartBracket mounting panel. The integrity

of the device enclosure and the mounting

panel is not compromised—normal state.

Learn more

Table des matières

Autres manuels AJAX Capteur de sécurité

AJAX

AJAX GlassProtect Manuel utilisateur

AJAX

AJAX DoorProtect Plus Manuel utilisateur

AJAX

AJAX vhfBridge Manuel utilisateur

AJAX

AJAX ReX Manuel utilisateur

AJAX

AJAX FireProtect 2 Jeweller Manuel utilisateur

AJAX

AJAX CombiProtect Manuel utilisateur

AJAX

AJAX DoorProtect Manuel utilisateur

AJAX

AJAX FireProtect Manuel utilisateur

AJAX

AJAX FireProtect 2 Jeweller Manuel utilisateur

AJAX

AJAX FireProtect Manuel utilisateur

AJAX

AJAX DualCurtain Outdoor Manuel utilisateur

AJAX

AJAX FireProtect Manuel utilisateur

AJAX

AJAX GlassProtect Manuel utilisateur

AJAX

AJAX DoorProtect Plus Manuel utilisateur

AJAX

AJAX FireProtect 2 Jeweller Manuel utilisateur

AJAX

AJAX LeaksProtect Manuel utilisateur

AJAX

AJAX MotionCam PhOD Jeweller Manuel utilisateur

AJAX

AJAX GlassProtect Manuel utilisateur

AJAX

AJAX FireProtect Manuel utilisateur

AJAX

AJAX Fire Protect Manuel utilisateur

AJAX

AJAX MotionProtect Plus Fibra Manuel utilisateur

AJAX

AJAX MotionProtect Manuel utilisateur

AJAX

AJAX HomeSiren Manuel utilisateur

AJAX

AJAX CombiProtect Manuel utilisateur

Manuels Capteur de sécurité populaires d'autres marques

THORLABS

THORLABS PDA10JT Manuel utilisateur

Waeco

Waeco UV-DETECT Manuel utilisateur

Intermatic

Intermatic IOS-DSIMF Manuel utilisateur

urmet domus

urmet domus 1083 Manuel utilisateur

Siemens

Siemens AZL66 Series Manuel utilisateur

BTI

BTI Profiline Multi Finder Manuel utilisateur

Challenger

Challenger SL01 Manuel utilisateur

DMP Electronics

DMP Electronics 1122INT Manuel utilisateur

Rielta

Rielta Ladoga MK-RK Manuel utilisateur

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuel utilisateur

Bosch

Bosch DS835 Manuel utilisateur

DBI SALA

DBI SALA EZ Stop Manuel de l'opérateur

Lamptime

Lamptime ST05C Manuel utilisateur

Ubiquiti

Ubiquiti MFI-MSC Manuel utilisateur

Subsite

Subsite 910R Instructions d'installation

Satel

Satel OPAL Pro Manuel utilisateur

Aleph

Aleph XC-1XTEU Manuel utilisateur

Pima

Pima LARIS QUAD Manuel utilisateur