ACME DAZZLED COLORLED-430 Manuel utilisateur

DAZZLED COLOR

LED-430

User Manual

Professional Entertainment Technology

TABLE OF CONTENTS

1. Safety Instruction

2. Technical Specification

3. Installation

4. How to Control the Unit

5. DMX 512 Configuration

6. DMX 512 Connection

7. Fixture Cleaning

1. Safety Instruction

WARNING

♦Please keep this User Manual for future consultation. If you sell the unit to another user,

be sure that they also receive this instruction booklet.

♦Unpack and check carefully there is no transportation damage before using the unit.

♦Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

♦It’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

♦The unit is for indoor use only and use only in a dry location.

♦The unit must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces. Be sure that no ventilation slots are blocked.

♦Disconnect mains power before fuse replacement or servicing.

♦Replace fuse only with the same type.

♦Make sure there are not flammable materials close to the unit while operating as it is fire

hazard.

♦In the event of serious operating problem, stop using the unit immediately. Never try to

repair the unit by yourself. Repair carried out by unskilled people can lead to damage or

malfunction. Please contact the nearest authorized technical assistance center and

always use the same type spare parts.

♦Do not touch any wire during operation as high voltage might be causing electric shock.

Please read the instruction carefully which including important

information about the installation, operation and maintenance.

For power supply, do not connect in series much more than 86 units, use

another mains supply for next 86 units.

2. Technical Specification

yIt can be operated by DMX512 control or can be used as an individual unit without

controller.

yIt can be linked together as many as required in master/slave mode, and perform the

great built-in programmed lighting shows triggered by music.

yPlease use a 3 pin XLR cable/plug when connecting them together.

yFan cooled.

y4Channels:

Channel 1 = Red

Channel 2 = Green

Channel 3 = Blue

Channel 4 = Dimmer/Strobe

yVoltage: AC 100V-240V 50/60Hz

yPower: 7 W

yLight Source: 1×3W RGB LED

yDimension: 222x300x124mm

yWeight: 1.3 kg

3. Installation

You can install the unit on the truss or ceiling, Use clamps to fix the unit to truss. Always

ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always

ensure that the structure to which you are attaching the unit is secure and is able to support

a weight of 10 kg for each unit.

4. How To Control The Unit

Three ways to operation:

A. Master/Slave operation

B. Easy controller CA-8

C. Universal DMX controller

A. Master/Slave operation

The unit can be linked together in daisy chain as many as you need in master/slave mode to

perform the great built-in pre-programmed lighting shows triggered by music.

In Master/Slave mode, refer to the DMX settings below:

Master unit: DIP switch #10 = ON

Slave units: All DIP switches OFF

2-light show:

Turn on the DIP switch #10 for the first unit and DIP switches #1 and #3 for the other, then

you can enjoy different lighting shows of the two units.

B. Easy Controller (by CA-8)

The easy remote control is used only in master/slave mode. By connecting to the 1/4”

microphone jack of the first unit (its DMX input plug is not used), you will find that the remote

control all the first unit will control all the other units for Stand by, Function and Mode. Built-in

lighting shows triggered by Easy Controller:

Stand by Blackout the unit

Function

1. Synchronous Strobe

2. Four light Strobe

3. Sound Strobe Chase

Mode Strobe (LED OFF) Latch (LED ON)

C. Universal DMX controller

When using a universal DMX controller to control the chain of units, you have to set DMX

address by Dip switches from 1 to 9 to make sure all the units will receive its DMX signal.

Please refer to the following diagram to know how to address your DMX 512 system in the

binary code.

DMX 512 Address Chart:

Dip-switches#1#2#3#4#5#6#7#8#9 #10

Value 1 2 4 8 16 32 64 128 256 4-light show

•Examples:

Channel 1：dip / on: #1 (=1)

Channel 5：dip / on: #1, #3 (1+4=5)

Channel 9：dip / on: #1, #4 (1+8=9)

Channel 13：dip / on: #1, #3, #4 (1+4+8=13)

5. DMX 512 Configuration

6. DMX 512 Connection

The DMX 512 is widely used in intelligent lightings and with a maximum of 512 channels.

1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin

adapter-cable.

2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120

ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin

XLR-plug and plug it in the DMX-output of the last unit.

3. Connect the unit together in a ‘daisy chain’ by XLR plug from the output of the

unit to the input of the next unit. The cable can not be branched or split to a ‘Y’

cable. DMX 512 is a very high-speed signal. Inadequate or damaged cables,

solder joints or corroded connectors can easily distort the signal and shut down

the system.

4. The DMX output and input connectors are pass-through to maintain the DMX

circuit, when power is connected to the unit.

5. Each lighting unit needs to have an address set to receive the data sent by the

controller. The address number is between 0-511 (usually 0 & 1 are equal to 1).

6. The end of the DMX 512 system should be terminated to reduce signal errors.

7. 3 pin XLR connectors are more popular than 5 pin XLR.

3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

7. Fixture Cleaning

The cleaning of internal and external optical lenses and/or mirrors must be carried out

periodically to optimize light output. Cleaning frequency depends on the environment in

which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater

accumulation of dirt on the unit’s optics.

yClean with soft cloth using normal glass cleaning fluid.

yAlways dry the parts carefully.

yClean the external optics at least every 20 days. Clean the internal optics at least every

30/60 days.

10B

EC - Declaration of Conformity

We declare that our products (lighting equipments) comply with the following

specification and bears CE mark in accordance with the provision of the

Electromagnetic Compatibility (EMC) Directive 89/336/EEC.

EN55014-2: 1997 A1: 2001, EN61000-4-2: 1995; EN61000-4-3: 2002;

EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6: 1996,

EN61000-4-11: 1994.

Harmonized Standard

EN60598-1: 2000+ALL: 2000+A12: 2002

Safety of household and similar electrical appliances

Part 1: General requirements

11B

Innovation, Quality, Performance

Table des matières

Autres manuels ACME Équipement d'éclairage

ACME

ACME PEXEL 100 Manuel utilisateur

ACME

ACME Andromeda Manuel utilisateur

ACME

ACME Theatre Spot 150 Manuel utilisateur

ACME

ACME Oxygen Manuel utilisateur

ACME

ACME V-BOX Manuel utilisateur

ACME

ACME GLAMOUR 700Z RGBY Manuel utilisateur

ACME

ACME LED-HC101 II Manuel utilisateur

ACME

ACME Spider FC Manuel utilisateur

ACME

ACME Energy Spot PRO Manuel utilisateur

ACME

ACME IM-250 SP Manuel utilisateur

ACME

ACME Pageant CM-200Z Manuel utilisateur

ACME

ACME Spartan Hybrid Manuel utilisateur

ACME

ACME SABER HYBRID PRO Manuel utilisateur

ACME

ACME iSolution Manuel utilisateur

ACME

ACME CHIRON Manuel utilisateur

ACME

ACME MP-12FC Manuel utilisateur

ACME

ACME LED-SC252 Manuel utilisateur

ACME

ACME TV LIGHT PANEL 2000 Manuel utilisateur

ACME

ACME STORM Manuel utilisateur

ACME

ACME LED-MS600 PE Manuel utilisateur

ACME

ACME LED-0408 Manuel utilisateur

ACME

ACME ENERGY HYBRID X-400 BSW Manuel utilisateur

ACME

ACME Stag Par MP-200 Manuel utilisateur

ACME

ACME DIABOLO 500 Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur