ZyXEL Communications FMT3211 Manuel utilisateur

www.zyxel.com

FMT3211

UMTS Small Cell CPE

Edition 1, 05/2013

User’s Guide

Safety Warnings

GENERAL: Please read this Getting Started Guide carefully before using FMT3211. The

FMT3211’s purpose is to provide improved mobile signal

coverage

inside a building.

Do not use this device for any other purpose, as doing so may be dangerous.

PLACEMENT: The FMT3211 and all its components (including cables and power adaptor)

should be placed in a dry, indoor area, at elevated heights such as on top of shelves,

cabinets, etc. It should be kept away from any wet or damp environments; such as

kitchens, bathrooms, laundry rooms or any other areas with exposure to moisture, sprays,

drips, or running water. For the safety of stored data, it should not be placed near

magnetic devices such as audio or video tapes, diskettes or credit cards. While in service,

the antenna should not be next to any another antenna or transmitting device.

MEDICAL DEVICES: The FMT3211 contains a radio transmitter similar to other residential

radio transmitters. Medical devices such as pacemakers and hearing aids may be affected,

unless precautions are taken, when using this device. Please contact your General

Practitioner for additional safety guidelines.

COMPLIANCE WITH APPLICABLE EXPOSURE LIMITS:The FMT3211 has a radio emission level well

below regulatory limits for public exposure to radiofrequency emissions. It thus complies

with the European Recommendation 1999/519/EC of 12 July 1999.

The European standard EN 50385 specifies the conditions for compliance with regulatory

limits for public exposure; in particular in the limiting case where the user would be located

at less than 20 cm of the unit in operation, the Specific Absorption Rate (SAR) must be

less than 2 W / kg.

The FMT3211 has a Specific Absorption Rate (SAR) of 0.088 W /Kg, is compliant with EN

50385 even when it is in this maximum power and in the immediate vicinity of the human

body.

EMERGENCY: The FMT3211 does not operate during instances of power loss. To make

emergency calls, please use a mobile or land line phones

POWER SUPPLY: Ensure that the voltage specified corresponds to the power socket to

which you connect it. In case of power loss (and therefore loss of service), all mobile

calls, including emergency calls, will be redirected automatically to the default mobile

(carrier) network. If you have no mobile network coverage and need to make an

emergency call, please use a land line. In case of a thunderstorm, please disconnect

the device to avoid damaging

it. For safety reasons, only service technician’s skills

can open the device.

CE MARKING: The CE marking of the FMT3211 certifies that this product meets the basic

requirements of the European Parliament and Council directive

1999/5/

CE on

telecommunications terminal equipment regarding; safety and health of users and

electromagnetic i n t er f e re n c e. For the declaration of compliance, please consult:

http://ec.europa.eu/enterprise/sect

ors/rtte/documents/

DISPOSAL &RECYCLING: To facilitate disposal and/or recycling, please respect the sorting

rules of your country or region for this kind of device. European regulations require the

disposal of this device at sales points or at designated collection points such as drop-off

centers,

etc.

Contents

Welcome...................................................................4

Unpacking Your FMT3211......................................5

Overview of the FMT3211.......................................6

FMT3211 Back Panel...............................................7

Quick Setup..............................................................8

Final Checks & Making Your First Call................12

Frequently Asked Questions (FAQ).......................14

Troubleshooting .....................................................16

Legal Information...................................................18

Welcome

The FMT3211 provides enhanced mobile voice and data service within

the building. It delivers high quality voice calls and faster, more reliable

mobile data service.

The FMT3211 connects to your broadband Internet service to deliver

extended indoor mobile network coverage. The in-building mobile

phone connectivity, signal quality, and data bandwidth will greatly

improve, especially if the building is in a remote area or out of adequate

mobile phone tower range.

Inside this packaging you will find: the FMT3211, an Ethernet cable, a

stand and an AC power adaptor. The FMT3211 has a zero touch set-up

process. Just install as detailed in this guide and it connects to your

mobile phone automatically whenever your phone is within range.

Before you begin you need to make sure you have the following:

• High Speed Internet service and an available Ethernet LAN port on

your router.

• An available power socket or electrical outlet.

Unpacking Your FMT3211

User’s Guide (this

document) FMT3211 AC Power Adaptor

Stand Wall Mounting Kit:

Cheese Screws (2)

Wall Anchors (2)

Ethernet Cable

Overview of the FMT3211

Status Indicators

Status indicators only become visible when the FMT3211 is powered

and the appropriate feature is operational. See the Troubleshooting

section on page 16 for the detailed indicator behaviors.

Power - Power status of the FMT3211.

Red: the FMT3211 is powered on

Red Flashing: a configuration problem has been detected; see

Troubleshooting section

Internet - Status of the IP link and network.

White: connected to the network

White Flashing: connection in progress

Small Cell Service - Availability of the small cell services.

White: the FMT3211 is ready for use

Orange: service failure; see Troubleshooting section

Small Cell Use - Status of the system (calls or internet

connections in progress).

White: one or more active users

White Flashing: maximum number of eight concurrent users

reached

FMT3211 Back Panel

The Ethernet port status

indicator LEDs will turn

off after 60 seconds to avoid

light pollution.

LAN2 Port

(connect to 3rd party device,

such as a computer if required)

LAN1 Port

(connect to high speed internet)

Reset / switch off Button: Press one time to reset the product.

Press 10 seconds and release to switch off the product.

Power

Quick Setup

Installing the FMT3211 is simple and can be completed within 5 to 20

minutes. The following instructions will guide you through the Quick

Setup process.

1. Find a central location in your building or office to install the device.

The FMT3211 emits a radio signal similar to a Wi-Fi router. The quality of

the coverage you will experience depends on where the device is

located and it should be placed:

• In a central area of your building.

• As high as possible; on top of tall furniture, shelves, cabinets, etc.

To improve coverage the following should be avoided:

Installing near other radio transmitters

Installing near metallic devices such as radiators

Installing near a window

2. Device placement:

The FMT3211 should be placed free standing on a flat sturdy surface.

First, power up your DSL router. Connect the Ethernet cable to an

available Ethernet port on your DSL/Cable router.

Then connect the other end of the Ethernet cable to the FMT3211 LAN1

port. Connect the power adaptor cable into the jack named Power, and

then plug the power adaptor to an AC socket.

After a few seconds the Power status indicator lights up, and the

Ethernet port status indicators on both the FMT3211 and the DSL/Cable

router should light up green (flash green). After 60 seconds the Ethernet

port status indicator light on the FMT3211 will automatically shutdown.

For free standing installation, place the FMT3211 in the stand as shown.

3. Broadband Connectivity:

After approximately two minutes, the FMT3211 Internet status

indicator will begin to pulse.

4. Automatic Software Update:

After the device establishes a broadband connection to your Internet

Service Provider (ISP), the FMT3211 automatically updates its software.

This process takes about 15 minutes and the Internet status

indicator pulses during this period.

After the device retrieves its software update package, it reboots

automatically.

During reboot, the Power status indicator is on.

5. Auto-configuration:

Table des matières

Autres manuels ZyXEL Communications Matériel réseau

ZyXEL Communications

ZyXEL Communications RS-1612 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications NSA-220 Plus Manuel utilisateur

ZyXEL Communications

ZyXEL Communications PLX-111 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZYWALL OTPV2 - Manuel utilisateur

ZyXEL Communications

ZyXEL Communications NSA-220 Plus Manuel utilisateur

ZyXEL Communications

ZyXEL Communications IES-708 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications NSA325 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications POE-12 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications NSA-220 Plus Manuel utilisateur

ZyXEL Communications

ZyXEL Communications FMG3010-R20A Manuel utilisateur

ZyXEL Communications

ZyXEL Communications NSA-220 Series Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZyWall Manuel utilisateur

ZyXEL Communications

ZyXEL Communications FMG Series Manuel utilisateur

ZyXEL Communications

ZyXEL Communications VPN Series Manuel utilisateur

ZyXEL Communications

ZyXEL Communications Network Storage Appliance NSA-220 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications VES1724-56 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications FTU2000 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications WAP6405 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications POE-12 Guide de référence

ZyXEL Communications

ZyXEL Communications ZyAIR B-320 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications PoE12 Series Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZYAIR Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZyWALL SSL 10 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications NSA-220 Plus Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur