ZyXEL Communications PLA450 Series Manuel utilisateur

PLA450 Series

Homeplug AV to WLAN AP/Bridge

Quick Start Guide

Version 3.60

1/2008

Edition 3

DEFAULT LOGIN

IP Address http://192.168.1.2

Password 1234

CONTENTS

ENGLISH 2

DEUTSCH 18

ESPAÑOL 36

FRANÇAIS 52

ITALIANO 70

SVENSKA 88

ENGLISH

The PLA450 connects your HomePlug AV powerline network (which uses your electrical

wiring) to your wired LAN (which uses Ethernet cables). It also adds wireless connectivity.

Use the following sections in this guide to set up a wireless and HomePlug AV powerline

network.

Section 1 :Initial Hardware Connections

Section 2 :Accessing the Web Configurator

Section 3 :Connect Wirelessly to the PLA450

Section 4 :Set Up a HomePlug AV Powerline Network

Section 5 :Set Your PLA450’s IP Address

Section 6 :Connect to the Internet

See the User’s Guide on the included CD for details on all of the PLA450’s features. If a

screen does not pop-up when you insert the included CD, use Windows Explorer (My

Computer) to go to the CD-ROM (commonly drive D) and browse for the User’s Guide.

"Your PLA450 is only compatible with HomePlug AV products with the latest

firmware. You can upgrade your other ZyXEL HomePlug AV products by

downloading the latest firmware from the ZyXEL website (www.zyxel.com).

Internet

ENGLISH

1 Initial Hardware Connections

1Screw the antenna clockwise onto the antenna connector. Make sure it is securely

attached. Point the antenna up (perpendicular to the ground).

2Use the yellow (Ethernet) cable to connect the PLA450’s LAN port to the Ethernet port

on your computer.

3Use the included power cord to connect the POWER socket to an appropriate power

source. This is also your powerline connection.

1.1 Look at the LEDs (lights)

•Power ( ): Blinks until the device is ready.

•HomePlug ( ): Turns on when connected to other HomePlug AV device(s).

•LAN ( ): Turns on if the LAN connection to your computer is OK.

•WLAN ( ): Turns on if the wireless LAN feature is on.

ENGLISH

VIf the power ( ) or LAN ( ) lights do not turn on, check your connections.

2 Accessing the Web Configurator

Access the PLA450’s web configurator to enter or change settings on the PLA450.

2.1 Give Your Computer a Static IP Address

Follow these instructions for Windows XP. If you do not have Windows XP, see the

appendix in the User’s Guide on setting your IP address.

1Click the network icon (usually in the bottom right of your

computer screen).

2Click Properties.

ENGLISH

3Select Internet Protocol (TCP/IP) (A). Then click Properties (B).

"Make a note of your original settings in (C) in the following screen if you will

return the computer to its original hardware connections after configuring

the PLA450.

4Type 192.168.1.x as the IP address, where xis a number between 3 and 254. Avoid IP

addresses taken by other devices on your network, such as 192.168.1.2, which is the

PLA450’s default IP address. Type 255.255.255.0 as the Subnet mask. Click OK.

2.2 Log Into the Web Configurator

The PLA450’s web configurator lets you enter and change settings.

ENGLISH

1Launch an Internet browser (such as Internet Explorer). Enter “http://192.168.1.2” and

click Go (or press [ENTER]).

VIf the login screen does not display, make sure your computer is using a

static IP address between 192.168.1.3 and 192.168.1.254, as shown in

section 2.1. If that doesn’t work, check your web browser’s pop-up settings

(see the User’s Guide for more information).

2The default password (1234) is entered for you. Click Login.

3Change the password in the next screen and click Apply.

4Click Go to Basic setup.

3 Connect Wirelessly to the PLA450

You can use either Wi-Fi Protected Setup (WPS) or the web configurator to set up your

wireless connection and network.

ENGLISH

If your wireless devices display the WPS logo, as shown below, use WPS to set up your

wireless network. Go to Section 3.1 to set up your wireless network.

If your wireless devices do not display the WPS logo, go to Section 3.2 to set up wireless

settings on your PLA450 using the web configurator.

3.1 Connect Wirelessly with WPS

Use WPS to connect WPS-enabled wireless devices to your PLA450 one at a time.

1Place a WPS-enabled device within range of the PLA450.

2Press the WPS button on both devices. It doesn’t matter which button is pressed first.

You must press the second button within two minutes of pressing the first one.

"Your PLA450 has a WPS button located on its housing, as well as a WPS

button available in the web configurator used to manage the PLA450. Other

WPS-enabled devices will have at least one WPS button.

minutes

ENGLISH

3The WPS LED ( ) on the PLA450 blinks for a few seconds, then shines steadily,

indicating your devices are connected.

4To add another WPS enabled device to your wireless network, press the WPS buttons

on your PLA450 and your next WPS-enabled device.

Congratulations! When you have finished setting up your wireless network, go to Section

4.1 to set up your powerline network.

3.2 Manually Set up a Wireless Network

If your wireless devices are not WPS-enabled, use your computer to manually set up your

wireless network.

3.2.1 Configure Your PLA450 With the Web Configurator

1Click Network > Wireless LAN in the web configurator’s navigation panel.

2The following screen appears.

•Name: Enter a descriptive name (up to 32 printable English keyboard characters) for your

wireless network.

•Security Mode: Select WPA-PSK.

ENGLISH

•Pre-Shared Key: Type a pre-shared key. Use 8 to 63 English keyboard characters (includ-

ing spaces and symbols). It is case-sensitive. Write it down to use in your wireless clients

so they can connect to the PLA450.

"Write down the name and pre-shared key to use in the wireless clients

later.

3Click Apply. Congratulations! You have configured the PLA450’s wireless settings and

are now ready to connect your other wireless devices to the PLA450.

3.2.2 Set Up a Wireless Network

You can now connect wirelessly to your PLA450 from your computer and access the

Internet. You will need the Network Name (SSID)and also the Pre-Shared Key if you set

up security in the previous section. The connection procedure is shown here using

Windows XP as an example.

ENGLISH

1Right-click the wireless adapter icon in the bottom right of your computer monitor. Click

View Available Wireless Networks.

2Select the SSID name you gave the PLA450 and click Connect (A).

3If you have set up wireless security, you are prompted to enter a password. Enter the

Pre-Shared Key you set up in the previous section and click Connect (B).

You may have to wait a few minutes while your computer connects to the wireless network.

4You should now be securely connected wirelessly to the PLA450.

Autres manuels pour PLA450 Series

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels ZyXEL Communications Matériel réseau

ZyXEL Communications

ZyXEL Communications ZyXEL ZyWALL P1 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications NXC Series Mode d’emploi

ZyXEL Communications

ZyXEL Communications Centralized Network Management Vantage CNM Manuel utilisateur

ZyXEL Communications

ZyXEL Communications Network Storage Appliance NSA-220 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications PM7516-R0 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications Internet Security Gateway ZyWALL 100 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications VMG4005-B60A Manuel utilisateur

ZyXEL Communications

ZyXEL Communications UNS2300 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications Prestige 2602R Series Manuel utilisateur

ZyXEL Communications

ZyXEL Communications PK5000Z Manuel utilisateur

ZyXEL Communications

ZyXEL Communications NSA-220 Plus Manuel utilisateur

ZyXEL Communications

ZyXEL Communications FMG3010-R20A Manuel utilisateur

ZyXEL Communications

ZyXEL Communications Prestige 971M Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZYAIR G-110 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications GS3700 Series Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZyAIR B-320 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications USG FLEX 500 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications FMT3211 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications Network Storage Appliance NSA-220 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications NSA-220 Plus Manuel utilisateur

ZyXEL Communications

ZyXEL Communications EOC350 Series Manuel utilisateur

ZyXEL Communications

ZyXEL Communications IES-1248 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications NSA-220 Series Manuel utilisateur

ZyXEL Communications

ZyXEL Communications FiberHome AN5516-06 Mode d’emploi

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur