Zte Falcon Z-917 Mode d’emploi
TCS530100.1
2.875”
4.875”
2.875”
GETTING TO KNOW YOUR
MOBILE HOTSPOT
LED
indicators
Charging & USB port
ON/OFF switch WPS key
micro-SIM card slot
Part Description
ON/OFF
switch Slide it to turn on/off the
Hotspot.
micro-SIM
card slot Install the micro-SIM card
(included).
WPS key
When the Wi-Fi function is
enabled, hold it for more than
3 seconds to activate the
WPS function.
1
LED
indicators It shows the signal strength,
battery, Wi-Fi and message.
Charging/
USB port
Charge your device.
Connect the client to your
device via USB cable.
Reset point
Insert a pin and hold it for 3 seconds to reset
your device.
2
INDICATORS
When the Hotspot is powered on, the following
icons will light up. For a description of the
icons, refer to the following table.
Indicator Status Description
Network
Red solid
Limited or no service,
no SIM card or SIM
card error, registered
to the LTE/UMTS/
HSPA network.
Green
solid
Registered to the
UMTS or HSPA
network and
connected to UMTS
or HSPA network.
Blue solid
Registered to
LTE network and
connected to LTE
network.
3
SMS
Blue solid You have unread
messages or FOTA
(new software).
Blue
blinking Your inbox is full or
FOTA upgrading.
LED light
off No unread messages
or no new messages.
Wi-Fi
Blue solid Wi-Fi is on.
Blue
blinking WPS is active.
LED light
off Wi-Fi is off.
Battery
Red solid
The battery is low.
(From 10% to dead)
Please charge the
battery.
Green
blinking The battery is being
charged.
Green
solid
The battery level is
middle or high. (From
100% to 11%)
LED light
off The battery is not
inserted.
4
SET UP YOUR MOBILE
HOTSPOT
1. Lift SIM card cover.
2. Install SIM card.
5
3. Power on.
Slide to turn on
Charge your Mobile Hotspot
You can charge your Mobile Hotspot by using
the charger included in the box or by plugging
it into your computer using the USB cable.
6
Install the battery
1. Remove the cover.
2. Install the battery.
7
CONNECT & GO
Connect your Wi-Fi device to your
Mobile Hotspot
1. Power on your Mobile Hotspot.
2. On your computer or other Wi-Fi enabled
device, search for available Wi-Fi Networks
and select the default Network Name
(SSID) for your Mobile Hotspot.
Note:
You can view the label on the device to get the
default Wi-Fi SSID and password.
3. Enter the default password and click OK.
4. Open a web browser and go to
www.T-Mobile.com/ConnectMe
Simply follow the on-screen instructions
to set up your No Annual Contract data
service.
Note: Service or use is your agreement to
T-Mobile’s Terms and Conditions. T-Mobile
requires ARBITRATION of disputes
UNLESS YOU OPT-OUT WITHIN 30 DAYS
OF ACTIVATION. See T-Mobile’s Terms and
Conditions for details at www.T-Mobile.com/
terms-conditions.
8
Table des matières
Autres manuels Zte Routeur sans fil
Zte
Zte 203Z Instructions d'installation
Zte
Zte OPTUS MF920V Manuel utilisateur
Zte
Zte MC7010 Manuel utilisateur
Zte
Zte MF63 Manuel utilisateur
Zte
Zte MF970 Manuel utilisateur
Zte
Zte MF60 Manuel utilisateur
Zte
Zte MF65 Manuel utilisateur
Zte
Zte MF93D Manuel utilisateur
Zte
Zte Tata Docomo Manuel utilisateur
Zte
Zte MF920U Manuel utilisateur
Zte
Zte Centinel MF275/9 Manuel utilisateur
Zte
Zte EuFi890 Manuel utilisateur
Zte
Zte MF65 Manuel utilisateur
Zte
Zte MF286R Manuel utilisateur
Zte
Zte MF51 Manuel utilisateur
Zte
Zte AT&T Velocity MF923 Manuel utilisateur
Zte
Zte Z6200 Instructions originales
Zte
Zte MF971L Instructions d'installation
Zte
Zte R218z Fiche technique
Zte
Zte MF93D Manuel utilisateur
