Zortrax Z-PLA Pro Instructions de montage

Tips for Printing with Z-PLA Pro

SOURCE:

https://support.zortrax.com/z-pla-pro-tips/

Table Of Content

Hotend Requirements 3

Extruder Upper Fan Operation 4

Platform Calibration Requirements 5

Temperature Tips 6

Leaving the Model on the Platform 7

Hotend Requirements

Use a separate hotend that will be dedicated only for printing with Z-PLA Pro. The

hotend should be new and not used with other materials during different projects.

Unload Z-PLA Pro from the hotend immediately after the printing process. Do not keep

the overheated material loaded in the extruder to avoid material degradation in the

nozzle.

Extruder Upper Fan Operation

Check if the extruder upper fan is operating properly. A faulty fan can cause Z-PLA Pro

to overheat which can have a negative influence on the printing process.

Also, use compressed air to clean the extruder upper fan and its heat sink from dust.

Platform Calibration Requirements

You should calibrate the platform before loading Z-PLA Pro into the hotend – the

extruder needs to be empty during the procedure. The nozzle becomes very hot during

the calibration and it could cause the material to overheat which can bring poor printing

results.

Temperature Tips

Remove the side covers before using Z-PLA Pro. This material is sensitive to high

temperatures so the recommended temperature in the print room is below 25° C [77°

F].

Leaving the Model on the Platform

Once the printing process has been finished, leave the model on the platform for about

30 minutes to let it cool off. This will make it easier for you to remove your print from the

platform. Also, you will be able to remove the raft and support structures from the model

more easily.

Powered by TCPDF (www.tcpdf.org)

Table des matières

Autres manuels zortrax Imprimante 3D

zortrax

zortrax M200 Manuel d'utilisation et d'entretien

zortrax

zortrax M300 Manuel d'utilisation

zortrax

zortrax DSS Manuel utilisateur

zortrax

zortrax M300 Feuille d'instructions

zortrax

zortrax M300 Plus Manuel d'utilisation

zortrax

zortrax Inkspire Manuel utilisateur

zortrax

zortrax M200 Manuel utilisateur

zortrax

zortrax Endstop Sleeve Manuel utilisateur

zortrax

zortrax M200 Plus Manuel d'utilisation et d'entretien

zortrax

zortrax M200 Manuel utilisateur

zortrax

zortrax M200 Manuel d'utilisation et d'entretien

zortrax

zortrax Inkspire Manuel utilisateur

zortrax

zortrax Inventure Feuille d'instructions

zortrax

zortrax M Series Manuel d'utilisation et d'entretien

zortrax

zortrax M200 Manuel utilisateur

zortrax

zortrax M200 Manuel

zortrax

zortrax M200 Manuel utilisateur

zortrax

zortrax Inkspire Manuel utilisateur

zortrax

zortrax M200 Plus Manuel d'utilisation et d'entretien

zortrax

zortrax M200 Manuel utilisateur

zortrax

zortrax M200 Manuel d'utilisation

zortrax

zortrax M200 Plus Manuel utilisateur

zortrax

zortrax M300 Plus Feuille d'instructions

zortrax

zortrax M200 Manuel utilisateur

Manuels Imprimante 3D populaires d'autres marques

Ultimaker

Ultimaker S5 Material Station Manuel utilisateur

EcubMaker

EcubMaker TOYDIY Manuel utilisateur

AnyCubic

AnyCubic Kossel Plus Manuel utilisateur

ReDeTec

ReDeTec ProtoCycler Manuel utilisateur

Kywoo3D

Kywoo3D Tycoon IDEX Manuel utilisateur

CraftBot

CraftBot PLUS PRO Manuel utilisateur

3DGence

3DGence INDUSTRY F340 Manuel utilisateur

HP

HP Jet Fusion 4200 Mode d'emploi

Rokit

Rokit AEP Series Manuel utilisateur

AnkerMake

AnkerMake M5 Manuel utilisateur

DIYElectronics

DIYElectronics PRUSA I3 Instructions de montage

Ackuretta

Ackuretta FreeShape 120 Manuel utilisateur

LONGER

LONGER LK5Pro Manuel utilisateur

Stratasys

Stratasys J850 Manuel utilisateur

MakerBot

MakerBot Replicator Manuel utilisateur

Stratasys

Stratasys FDM Vantage Series Manuel utilisateur

ZYYX

ZYYX Pro II Manuel utilisateur

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guide de l'utilisateur