ZKTeco LPRS2000 Manuel utilisateur

Installation Guide

Version: 1.0

Date: March,2018

LPRS2000 Hybrid Recognition Integrated Machine

1. Installation Tools

Inner hexagon spanner, ground drill (the latter is not delivered with the product).

2. Safety Precautions

Carefully read this installation guide before installing and using the product. After the

installation is complete, strictly check the terminal connection according to the wiring

terminal diagram.

3. Overview

Reader

Chassis

Camera

Fill light

l Installation on a straight lane with booth

A straight lane is an ideal installation environment for capturing high-quality pictures

when vehicles move to the recognition area.

1)The integrated machine and the barrier gate can be installed on the same side of

the lane but the integrated machine must be installed in front of the barrier gate

with the gap of no less than 30cm so as to avoid mutual interference.

2)Recommended distance between the recognition area and the integrated

machine is 4~4.5m.

l Installation in an underground garage

When installing the integrated machine in an underground garage, follow the

principle below:

1)Entrance: Install the integrated machine on the horizontal road above the ramp of

the underground garage.

2)Exit: Install the integrated machine on the horizontal road below the ramp of the

underground garage.

l Installation on a curve lane

When the device is installed on a curve lane, the integrated machine shall be installed

on the external side of the curve.

l Installation on a broad lane

1)If a lane is too broad, you can divide the lane into two lanes or use barriers such as

cone buckets or road piles to mark out a non-motor vehicle lane so that the motor

vehicle lane becomes narrow and the vehicle movement direction is straight.

2)If a lane is too board but cannot be divided into two lanes or no non-motor vehicle

lane can be marked out, you can install two integrated machine, that is, install one

on each side of the lane.

3)If a lane is very short, install the integrated machine on the side which the vehicle

heads lean. When vehicles move from both directions, install one machine in each

direction to capture license plate pictures.

4. Installation Location

It is important for the integrated machine to quickly and accurately output license

plate recognition results and capture high-quality license plate pictures. Adjust the

angle and distance of the camera and the reader to ensure that complete and clear

license plate pictures are captured.

5. Installation Procedure

Step 1:Place the mounting sticker to the place where device needs to be installed and

drill.

Step 2:Insert the cover into the column 2; lay the cables from the hole of column 2 and

then screw it.

Step 3:Insert the column 1 into the column 2 and tighten it in by hand screws, as

shown in ﬁgure 1.

Note: Do not put your ﬁngers into the holes in the column 2 when installing!

Column 1

Cover

Hand screw

Column 2

Fill light

Chassis

Reader

Column 1

Camera

Column 2

Step 4:Place the sponge mats on column 1, then ﬁx the reader holder and the reader

support with a collet and M6 screws as shown in ﬁgure 3, 4.

Note: Recommended installation height is 2 m.

Figure 1 Figure 2

Step 5:Place the sponge mats on column 1, then lock the chassis holder and chassis

support with a collet and M6 screws as shown in ﬁgure 2.

Step 6:Place the sponge mats on column 1, fasten the cardan joint and install the

camera as shown in ﬁgure 5, 6.

Note: Recommended installation height is 1.2 m.

M6 screws

Reader holder

Sponge mats

Reader holder

Reader Reader support Column 1 Collet

M6 screws

Figure 4

Figure 3

Camera

Cardan joint

Fi g u r e 5

Camera control panel

GND

OUT

RST

AUDIO

GND

+12V

NO2

NO1

COM1

NC1

COM2

NC2

AUX2

GND

AUX1

OPEN

GND

485A2

485B2

485B1

485A1

WD1IN

WDOIN

GND

WD1

WD0

GND

6. Cable Connection Description

Wiring terminal diagram

Step 7: Place the sponge mats on column 2, then install the ﬁll light. Adjust the angle

as shown in ﬁgure 7.

M6 screws

Collet

Column 1 Camera support

Cardan joint

Camera

Figure 6

Chassis

Barrier

gate

Reader

Figure 7

ZKParking

L N

Air Switch

Dan ger Ele ctric S hock

Autres manuels pour LPRS2000

Table des matières

Autres manuels ZKTeco Terminal tactile

ZKTeco

ZKTeco ZKBio710 Series Manuel utilisateur

ZKTeco

ZKTeco F Series Manuel utilisateur

ZKTeco

ZKTeco FA2000 Manuel utilisateur

ZKTeco

ZKTeco ProFace X Manuel utilisateur

ZKTeco

ZKTeco MB10-VL Manuel utilisateur

ZKTeco

ZKTeco D3 Series Manuel utilisateur

ZKTeco

ZKTeco RevFace15 Manuel utilisateur

ZKTeco

ZKTeco VT07-C22L Manuel utilisateur

ZKTeco

ZKTeco iClock 885 Manuel utilisateur

ZKTeco

ZKTeco IN710 Manuel utilisateur

ZKTeco

ZKTeco uFace Plus Series Manuel utilisateur

ZKTeco

ZKTeco LockerPad-7B Manuel utilisateur

ZKTeco

ZKTeco ma 300 Manuel utilisateur

ZKTeco

ZKTeco G2 Manuel utilisateur

ZKTeco

ZKTeco FaceKiosk-H13 Manuel utilisateur

ZKTeco

ZKTeco S922 Series Manuel utilisateur

ZKTeco

ZKTeco LFace10 Manuel utilisateur

ZKTeco

ZKTeco G4 Manuel utilisateur

ZKTeco

ZKTeco ZKAIO4000W Manuel utilisateur

ZKTeco

ZKTeco MB20-VL Manuel utilisateur

ZKTeco

ZKTeco U1000F Manuel utilisateur

ZKTeco

ZKTeco F305 Manuel utilisateur

ZKTeco

ZKTeco FaceKiosk-H10A Manuel utilisateur

ZKTeco

ZKTeco ZKBio810 Series Manuel utilisateur

Manuels Terminal tactile populaires d'autres marques

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manuel utilisateur

Ingenico

Ingenico AXIUM EX4000 Manuel utilisateur

Heisei Electronics

Heisei Electronics Q-POS 815 Manuel utilisateur

Amano

Amano MTX-15 Manuel utilisateur

FLOWBIRD

FLOWBIRD CWT Compact Touch Manuel utilisateur

Demco

Demco SP7 Manuel utilisateur

Lathem

Lathem PC600 Series Manuel utilisateur

Partner

Partner MF-2352 Manuel utilisateur

NCR

NCR RealPOS 7460-2 Manuel

Simrad

Simrad MS50 Instructions de montage

Unitech

Unitech MR350 MKII Guide de démarrage rapide

Jungheinrich

Jungheinrich WMT 210 Manuel utilisateur

Motorola

Motorola MTP850 Manuel utilisateur

YASKAWA

YASKAWA 62H-MDC0 Manuel utilisateur

MVG industries

MVG industries NeptuLink Manuel utilisateur

Price Industries Limited

Price Industries Limited FDC Manuel d'instructions

Honeywell

Honeywell TemaKey Manuel utilisateur

EBN

EBN BPC65-B-A16G Manuel utilisateur