ZKTeco C3 Manuel utilisateur

ZK Access Quick Start Guide





Install C3 using TCP/IPmode of communication

C3 controller supports the connection from panel to server over RS485 data line and also via

nodes on TCP/IP Ethernet networks. This greatly increases the flexibility of installation options.

Note: Make sure the devices are in the same LAN network with server or directly connect to the

server using the TCP/IP communication.

TCP/IP Connection Cable Mode

There are two ways to connect to C3 controller.

○

1Network cable directly connects Management host and the device, without a hub.

○

2In a large office a hub/switch is needed to connect more than 2 devices.

The configuration is as follows:



TCP/IP Communication

How to add a device into ZKAccess software?

ZKAccess provides two ways to add a device.

○

1When the IP address of the device is already known, you can quickly add it by entering

the IP address as follow:

Click [Add] on the [Device-Device] interface.

ZK Access Quick Start Guide





As the interface appears, write the [Device Name], then give the [IP address] of the device. The

[IP Port No.] is defaulted to 4370 by the system. Please set the password if needed.

Note: Select the type of the device. If it is a Four-Door-One-Way Access Control Panel there will

appear an extra option-[Switch to Two-door Two-way]. Select as appropriate according to

the actual device.

Select the [Area] the device belongs to. If you do not want to clear the data (Information in Time

zones, Access Levels, etc.) in the device when adding, remove the check beside the [Clear Data in

the Device when adding] option. Click [OK] to add the device.

○

2Click [SearchAccess Control Panels] option on the [Device-Device] interface.

Click [Search], after searching, the usable device will show in the results list. Modify the IP

address to available IP, and then add the device.





ZK Access Quick Start Guide





Using fast search tool to modify the IPaddress of a device

ZK provides a fast search tool for searching devices and modifying the IP addresses. This allows

devices to be added directly without modifying the system, which is inconvenient and time

consuming.

The tool and the operation of searching and modifying are as follows:

Click [Search Panel] on the [Setting] dropdown menu.

After a few seconds results for the usable devices will appear.

Click to select the device and [Modify IPAddress] on the [Setting] dropdown menu to modify the

IP address of the devices.

Table des matières

Autres manuels ZKTeco Contrôleurs d'accès IP

ZKTeco

ZKTeco F18 Manuel utilisateur

ZKTeco

ZKTeco Green Label ProCapture-T Manuel utilisateur

ZKTeco

ZKTeco BioServer 2 Manuel utilisateur

ZKTeco

ZKTeco SpeedFace-V3L Manuel utilisateur

ZKTeco

ZKTeco SF1005-V+ Manuel utilisateur

ZKTeco

ZKTeco ProFace X Series Manuel utilisateur

ZKTeco

ZKTeco ProCapture-WP Manuel utilisateur

ZKTeco

ZKTeco ProFace X Manuel utilisateur

ZKTeco

ZKTeco Atlas Bio Series Manuel utilisateur

ZKTeco

ZKTeco ProMA Series Manuel utilisateur

ZKTeco

ZKTeco ProFace X SL Manuel utilisateur

ZKTeco

ZKTeco TF1600 ZKTeco Manuel utilisateur

ZKTeco

ZKTeco F6 Manuel utilisateur

ZKTeco

ZKTeco ProMA Series Manuel utilisateur

ZKTeco

ZKTeco C5S120 Mode d’emploi

ZKTeco

ZKTeco inBIO 480 Mode d’emploi

ZKTeco

ZKTeco SpeedFace M1 Manuel utilisateur

ZKTeco

ZKTeco PA10 Manuel utilisateur

ZKTeco

ZKTeco F18 Manuel utilisateur

ZKTeco

ZKTeco SA32-E Manuel utilisateur

ZKTeco

ZKTeco SilkID F21-ID Manuel utilisateur

ZKTeco

ZKTeco Horus Manuel utilisateur

ZKTeco

ZKTeco BioPro SA50 Manuel utilisateur

ZKTeco

ZKTeco ZPad Plus Manuel utilisateur

Manuels Contrôleurs d'accès IP populaires d'autres marques

Jantar

Jantar REX A-1-9 Manuel utilisateur

2N

2N Access Unit Feuille d'instructions

Kedacom

Kedacom KSCA120 Series Manuel utilisateur

H3C

H3C WX2880X Manuel utilisateur

G4S

G4S S870-EX Mode d’emploi

PRASTEL

PRASTEL M2000PE Manuel utilisateur

Allegion

Allegion interflex IF-281 Cylinder Manuel utilisateur

TECOM

TECOM TS1067E Manuel utilisateur

Fermax

Fermax Memokey 100C Guide de l'utilisateur

Fermax

Fermax CITYLINE MEMOKEY Mode d’emploi

Software House

Software House iSTAR Pro 2U RM Mode d’emploi

AKCP

AKCP SP+ Manuel utilisateur

Bpt

Bpt HNA/102 Manuel utilisateur

Civintec

Civintec CV9601T-T-1F Manuel utilisateur

BioMax

BioMax N-X90W Manuel utilisateur

FingerTec

FingerTec s-Kadex Manuel utilisateur

H3C

H3C WX5002ACCESSCONTROLLER Manuel utilisateur

C Prox Ltd

C Prox Ltd DPN-2 Manuel utilisateur