YSI EcoSense DO200A Manuel utilisateur

USER MANUAL

English, Français, Español, Português

EcoSense®DO200A

EcoSense®DO200M

Dissolved oxygen & temperature

instruments

User Manual

DOCUMENT #606035REF

WARRANTY

The EcoSense® DO200A/DO200M Instrument is warranted for one year

from date of purchase by the end user against defects in materials and

workmanship. DO200A/DO200M probes and cables are warranted for

one year from date of purchase by the end user against defects in material

and workmanship. Within the warranty period, YSI will repair or replace, at

its sole discretion, free of charge, any product that YSI determines to be

covered by this warranty.

To exercise this warranty, write or call your local YSI representative, or

contact YSI Customer Service in Yellow Springs, Ohio. Send the product

and proof of purchase, transportation prepaid, to the Authorized Service

Center selected by YSI. Repair or replacement will be made and the

product returned, transportation prepaid. Repaired or replaced products

are warranted for the balance of the original warranty period, or at least 90

days from date of repair or replacement.

Limitation of Warranty

This Warranty does not apply to any YSI product damage or failure caused

by: (i) failure to install, operate or use the product in accordance with

YSI’s written instructions; (ii) abuse or misuse of the product; (iii) failure

to maintain the product in accordance with YSI’s written instructions or

standard industry procedure; (iv) any improper repairs to the product; (v)

use by you of defective or improper components or parts in servicing or

repairing the product; or (vi) modification of the product in any way not

expressly authorized by YSI.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR

IMPLIED,INCLUDINGANYWARRANTYOFMERCHANTABILITYORFITNESS

FOR A PARTICULAR PURPOSE. YSI’s LIABILITY UNDER THIS WARRANTY

IS LIMITED TO REPAIR OR REPLACEMENT OF THE PRODUCT, AND THIS

SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY FOR ANY DEFECTIVE

PRODUCT COVERED BY THIS WARRANTY. IN NO EVENT SHALL YSI BE

LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL

DAMAGES RESULTING FROM ANY DEFECTIVE PRODUCT COVERED BY

THIS WARRANTY

Contact Information

YSI

1725 Brannum Lane

Yellow Springs OH, 45387, USA

Tel: 800-897-4151 • 937-767-7241; Fax: 937-767-1058

E-mail: [email protected]

Web: ysi.com

606035REF-B-YSI-DO200A-DO200M-User-Manual-English.indd 2 12/7/2017 9:45:08 AM

CONTENTS

Safety Information ...............................................................................1

The Instrument Case..............................................................1

The Probe................................................................................1

Package Contents................................................................................2

Unpacking............................................................................................2

Installation............................................................................................3

Probe Preparation .................................................................3

Battery Installation .................................................................3

Intended Use and General Overview................................................4

Display Description.............................................................................5

Operational Keys Description ............................................................6

Operational Procedures......................................................................7

Measurement Modes - % or mg/L........................................7

Calibration ..............................................................................8

Temperature.....................................................................8

Dissolved Oxygen ...........................................................8

Saving, Viewing and Deleting Data......................................9

Downloading Data to a Computer - DO200M Only ........10

Recal Timer - DO200M Only...............................................10

Date/Time Settings - DO200M Only..................................10

Sensor Storage.....................................................................11

Short-term Storage ......................................................11

Long-term Storage ........................................................11

Troubleshooting ................................................................................11

Error Messages on Display .................................................11

Opening the Data File with Excel®.....................................12

606035REF-B-YSI-DO200A-DO200M-User-Manual-English.indd 3 12/7/2017 9:45:08 AM

Maintenance .....................................................................................13

Dissolved Oxygen Sensor ...................................................13

Temperature Sensor ............................................................14

Accessories / Part Numbers .............................................................14

Technical Support..............................................................................15

Specifications.....................................................................................15

606035REF-B-YSI-DO200A-DO200M-User-Manual-English.indd 4 12/7/2017 9:45:08 AM

SAFETY INFORMATION

Please follow the guidelines below, and read this manual in its entirety to

ensure safe operation of the unit.

Avoiding Damage to the Instrument - Precautions

The Instrument Case

Though the instrument is housed in a water-proof IP67 case, DO NOT use

it underwater. The cable connector is not waterproof unless the cap is

installed. In case of submersion without the cap connected, follow these

steps immediately:

1. Remove the battery and reinstall the battery cover.

2. Dry the connector if necessary, and replace the DO probe. Rinse unit

carefully with distilled water. After rinsing and drying, inspect and

clean connectors to remove all contaminants that may affect probe

connections.

3. Wait for unit and all connections to dry before reinstalling the battery

and resuming operation.

4. If the unit does not function correctly after step 3, contact YSI for

possible repair or replacement.

The Probe

1. Membranes last longer if properly installed and regularly maintained.

Erratic readings can result from damaged or fouled membranes or

from large bubbles in the electrolyte reservoir. If unstable readings

or membrane damage occurs, replace both the membrane cap

and Oxygen Probe solution (also known as “O2 Probe Electrolyte”,

potassium chloride, or KCl solution). The average replacement

interval is 4 to 8 weeks, although they may last longer if kept clean.

Harsh environments, such as wastewater, may require membrane

replacement every 2 to 4 weeks. Unstable readings may occur if

membrane cap is coated with oxygen consuming or oxygen evolving

organisms such as bacteria or algae.

2. Chlorine, sulfur dioxide, nitric oxide and nitrous oxide can affect

readings by behaving like oxygen at the probe.

3. Avoid substances that may damage probe materials such as

concentrated acid, caustics and strong solvents. Probe materials

include Stainless steel, epoxy and ABS Plastic.

4. Keep the probe’s gold cathode clean and textured (when properly

maintained it has a matte finish). If it is tarnished (from contact with

606035REF-B-YSI-DO200A-DO200M-User-Manual-English.indd 1 12/7/2017 9:45:08 AM

certain gases), or plated with silver (from extended use with a loose

or wrinkled membrane), then clean it, following the instructions in the

Maintenance section.

5. To prevent the membrane and electrolyte from drying out, store the

field probe in the calibration bottle with the moistened sponge. If

using the self-stirring 200-BOD probe for the lab, store it in a clean

BOD bottle with 1 inch of water to keep the probe in a saturated air

environment.

PACKAGE CONTENTS

Item # Contents

606077 DO200A meter, manual, and 9V battery

606071 DO200A meter, manual, 9V battery, transport case,

polarographic probe with 1 meter cable, 6 screw-on cap

membranes and electrolyte solution

606072 DO200A meter, manual, 9V battery, transport case,

polarographic probe with 4 meter cable, 6 screw-on cap

membranes and electrolyte solution

606040 DO200A meter, manual, 9V battery, transport case,

polarographic probe with 10 meter cable, 6 screw-on cap

membranes and electrolyte solution

601027 DO200M meter, manual, USB cable, and 9V battery

601028 DO200M meter, manual, USB cable, 9V battery, transport

case, polarographic probe with 1 meter cable, 6 screw-on

cap membranes and electrolyte solution

601029 DO200M meter, manual, USB cable, 9V battery, transport

case, polarographic probe with 4 meter cable, 6 screw-on

cap membranes and electrolyte solution

601030 DO200M meter, manual, USB cable, 9V battery, transport

case, polarographic probe with 10 meter cable, 6 screw-on

cap membranes and electrolyte solution

UNPACKING

Carefully unpack the unit and accessories, and inspect for shipping

damages. Compare received parts with materials listed in the Package

Contents section. Notify YSI immediately of any damage or missing parts.

Save all packing materials until satisfactory operation is confirmed.

606035REF-B-YSI-DO200A-DO200M-User-Manual-English.indd 2 12/7/2017 9:45:08 AM

INSTALLATION

Probe Preparation

The DO probe ships with a dry, protective membrane. To install a new

membrane cap on the probe:

1. Unscrew probe membrane cap and discard.

2. Fill a new cap with Oxygen Probe Solution. Prepare according to

directions on the solution bottle.

3. Thread filled membrane cap onto sensor. The sensor can be placed

in a 100% water-saturated air environment (see Dissolved Oxygen

Calibration section).

4. Allow sufficient warm-up time for initial use (10-15 min). During this

time an “ovEr” message may appear on the display. This is normal.

After the warm up is complete the message will disappear.

Battery Installation

An initial display of “BAT” on the LCD indicates approximately one hour of

battery life for unit operation within specifications. Replace battery when

“BAT” appears on the LCD.

To replace battery, remove the two battery

cover screws and the battery cover and o-ring

(Figure 1). Replace the 9V battery. Replace

the battery cover and o-ring (be sure to align

the o-ring correctly to prevent a bad seal) and

fasten the two battery cover screws for the

splash-resistant feature.

Battery Disposal

This instrument is powered by a 9 volt battery, which the user must remove

and dispose of when the batteries no longer power the instrument.

Disposal requirements vary by country and region, and users are expected

to understand and follow the battery disposal requirements for their

specific locale.

Figure 1

606035REF-B-YSI-DO200A-DO200M-User-Manual-English.indd 3 12/7/2017 9:45:08 AM

INTENDED USE AND GENERAL

OVERVIEW

The YSI DO200A and YSI DO200M are precise water quality instruments

that measure dissolved oxygen (DO) in addition to temperature. A built-

in microprocessor stores, calculates, and compensates for all parameters

related to DO determinations including DO electrode temperature

characteristics.

The DO200A and DO200M have a waterproof IP67 case when the

connector cap is installed. The keys are highly reliable with tactile and

audio feedback. These instruments use one 9V battery. Recalibration is

not required when power is restored.

The front of the instrument has a large LCD that displays temperature and

either DO % or DO mg/L (ppm). The instrument also displays user prompts

and mode indicators. The unit prompts the user through calibration and

measurement procedures.

The model DO200A/DO200M field and lab probes use a polarographic

electrode with convenient screw-on cap membranes. Field probes feature

a built-in temperature probe for automatic temperature compensation, as

well as a stainless steel body for added weight. The self stirring 200-BOD

lab probe (item # 609200) is also available.

Key differences between the YSI DO200A and DO200M include:

• DO200A can store 50 data sets, while the DO200M can store 250 data

sets.

• A real-time clock is included on the DO200M for date/time stamp of

saved data.

• The DO200M features a waterproof USB port with cover that will allow

customers to download stored measurement data to a PC.

• A recal prompt on the DO200M allows users to select a recalibration

interval.

606035REF-B-YSI-DO200A-DO200M-User-Manual-English.indd 4 12/7/2017 9:45:08 AM

DISPLAY DESCRIPTION

Number Description

1Low battery indicator

2Recal Timer indicator (DO200M only)

3Main display for dissolved oxygen values

4USB/PC connection indicator (DO200M only)

5Calibration mode indicator

6Data set number

7Temperature display

8Dissolved oxygen units (% or mg/L)

9mbar: Displays during calibration to prompt

user for true barometric pressure.

10 Save, Full, Recall, Each, All, Delete:

Instrument’s data storage indicators.

11 Date/Time display (DO200M only)

12 SAL ppt: Displays during calibration when

user is prompted for the approximate salinity

(in ppt) of the sample to be tested.

Figure 2

606035REF-B-YSI-DO200A-DO200M-User-Manual-English.indd 5 12/7/2017 9:45:09 AM

OPERATIONAL KEYS DESCRIPTION

Number Key Description

YSI EcoSense Handheld Overlay

12/19/2016

DO200M

colors:

Black background

PMS 7482 C power symbol

PMS 130 C logo

Reverse white all other imagery

DO200M

INPUT

EcoSense®

Mode

CAL

Recal

Timer

Date

Time

Power key. Turns the unit on or off.

2, 6

YSI EcoSense Handheld Overlay

12/19/2016

DO200M

colors:

Black background

PMS 7482 C power symbol

PMS 130 C logo

Reverse white all other imagery

DO200M

INPUT

EcoSense®

Mode

CAL

Recal

Timer

Date

Time

Up and down arrow keys. Used to

scroll through saved data in Recall

mode, select the data deletion

option in Delete mode, and adjust

input values for barometric pressure

and salinity during calibration. On

the DO200M, these keys adjust

recal time and select/adjust date

time format and information.

YSI EcoSense Handheld Overlay

12/19/2016

DO200M

colors:

Black background

PMS 7482 C power symbol

PMS 130 C logo

Reverse white all other imagery

DO200M

INPUT

EcoSense®

Mode

CAL

Recal

Timer

Date

Time

Calibration key. Press to enter

the calibration mode.

YSI EcoSense Handheld Overlay

12/19/2016

DO200M

colors:

Black background

PMS 7482 C power symbol

PMS 130 C logo

Reverse white all other imagery

DO200M

INPUT

EcoSense®

Mode

CAL

Recal

Timer

Date

Time

Recal Timer key (DO200M

only). Press to enter the Recal

Timer input display.

Figure 3

YSI EcoSense Handheld Overlay

12/19/2016

DO200M

colors:

Black background

PMS 7482 C power symbol

PMS 130 C logo

Reverse white all other imagery

DO200M

INPUT

EcoSense®

Mode

CAL

Recal

Timer

Date

Time

606035REF-B-YSI-DO200A-DO200M-User-Manual-English.indd 6 12/7/2017 9:45:09 AM

Autres manuels pour EcoSense DO200A

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels YSI Instrument de mesure

YSI

YSI Pro10 Manuel utilisateur

YSI

YSI Professional Plus Manuel d'utilisation et d'entretien

YSI

YSI 2730 Manuel utilisateur

YSI

YSI 5000 Manuel utilisateur

YSI

YSI EXO Manuel utilisateur

YSI

YSI 550 DO Manuel utilisateur

YSI

YSI SonTek RiverSurveyor Guide de l'utilisateur

YSI

YSI 900 Manuel utilisateur

YSI

YSI 2900 series Manuel utilisateur

YSI

YSI WaterLog Series Manuel utilisateur

YSI

YSI MultiLab 4010P-1W Manuel utilisateur

YSI

YSI Professional Plus Manuel utilisateur

YSI

YSI YSI 556 MPS Manuel utilisateur

YSI

YSI EcoSense pH1000A Manuel utilisateur

YSI

YSI ProDIGITAL Manuel utilisateur

YSI

YSI 2700 SELECT Manuel utilisateur

YSI

YSI Pro30 Manuel utilisateur

YSI

YSI 1500 Sport Manuel utilisateur

YSI

YSI 85 Manuel utilisateur

YSI

YSI 2700D Manuel utilisateur

YSI

YSI 550A Manuel utilisateur

YSI

YSI MultiLab 4010-1W Manuel utilisateur

YSI

YSI EcoSense DO200A Manuel utilisateur

YSI

YSI EcoSense ORP15A Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur