YSI Pro30 Manuel utilisateur

Pro30

Quick Start Guide

Item #606083

This pocket guide serves as a quick reference in calibrating and operating the Pro30

conductivity and temperature instrument. It is not intended to replace the information

found in the User Manual.

Calibration

The Pro30’s temperature sensor cannot be calibrated nor should calibration be

required. If the temperature sensor is not reading accurately, contact YSI or your local

representative

The Pro30’s conductivity sensor can be calibrated in conductivity, speciﬁc conductance

or salinity measurement mode. Calibrating any option will automatically calibrate the

others. YSI recommends calibrating in speciﬁc conductance for both ease and accuracy.

The following steps outline the speciﬁc conductance calibration.

1. Fill a clean container (ie plastic cup or glass beaker) with fresh, traceable

conductivity calibration solution and place the sensor into the solution. The

solution must cover the holes of the conductivity sensor that are closest to the

cable. Ensure the entire conductivity sensor is submerged in the solution or the

instrument will read approximately half the expected value.

2. Gently agitate the probe to remove any air bubbles from the conductivity

sensor.

3. Press and hold the Cal key for a few seconds. Highlight Sp. Conductance and

press Enter.

4. Highlight the units you wish to calibrate, either uS/cm or mS/cm, and press

Enter. 1 mS = 1,000 uS.

5. Next, use the up or down arrow key to enter the conductivity value of the

solution as it is labeled for 25°C. (Speciﬁc conductance is temperature

compensated conductivity and the instrument uses the default reference

temperature of 25° when calibrating speciﬁc conductance.) Depressing either

the up or down arrow key for 5 seconds will move the changing digit one place

to the left. The Pro30 will remember the calibration value and display it the next

time a calibration is performed.

6. Press Enter to conﬁrm the calibration value.

7. Wait for the readings to stabilize and then press Enter to complete the

calibration. Or, press Cal to cancel the calibration and return to the Run screen.

Viewing and Deleting Saved Data

To view saved data, highlight Data and press Enter. Use the up or down arrow key to

scroll through the saved data points. Press Enter to access the functions on the bottom

of the display. From there, you can highlight Erase and press Enter to delete data. Or,

highlight ESC and press Enter to return to the Run screen.

8. ‘Calibration Successful’ will display for a few seconds to indicate a successful

calibration and then the instrument will return to the Run screen.

If the calibration is unsuccessful, an error message will display on the screen. Press

the Cal key to exit the calibration error message and return to the Run screen. See

the Troubleshooting Guide in the Users Manual for information on how to correct the

problem. Possible solutions may include cleaning the conductivity sensor, ensuring the

correct value of the calibration standard is entered, ensuring the sensor is completely

submerged in the solution and/or using a new solution.

Taking Measurements

1. Ensure the conductivity sensor is completely submerged in the sample. The two

holes near the cable should be covered by the sample for accurate conductivity

readings.

2. Highlight Save and press Enter to store the reading. The instrument will conﬁrm

that the reading was successfully saved.

Visit YSI.com/Pro30 to ﬁnd the

User Manual, specs, and accessories.

Item# 606083 Dwg# 606083

November 2019 Rev B

1725 Brannum Lane

Yellow Springs, OH 45387

(800) 765-4974, (937) 767-7241

[email protected]

Contact Information

Autres manuels pour Pro30

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels YSI Instrument de mesure

YSI

YSI Pro10 Manuel utilisateur

YSI

YSI Pro2030 Manuel utilisateur

YSI

YSI 2900 series Manuel utilisateur

YSI

YSI Professional Plus Manuel d'utilisation et d'entretien

YSI

YSI EcoSense ORP15A Manuel utilisateur

YSI

YSI 900 Manuel utilisateur

YSI

YSI MultiLab 4010-1W Manuel utilisateur

YSI

YSI EcoSense pH1000A Manuel utilisateur

YSI

YSI MultiLab 4010-3W Manuel utilisateur

YSI

YSI 550A Manuel utilisateur

YSI

YSI MultiLab 4010-2W Manuel utilisateur

YSI

YSI WE KNOW ProOBOD Manuel utilisateur

YSI

YSI EcoSense pH100A Manuel utilisateur

YSI

YSI 650 MDS Manuel utilisateur

YSI

YSI YSI 556 MPS Instruction manuelle

YSI

YSI 3100 Manuel utilisateur

YSI

YSI ProDIGITAL Manuel utilisateur

YSI

YSI 550A Manuel utilisateur

YSI

YSI Professional Plus Manuel utilisateur

YSI

YSI 63 Manuel utilisateur

YSI

YSI 2700D Manuel utilisateur

YSI

YSI EcoSense DO200A Manuel utilisateur

YSI

YSI IDS WA Manuel utilisateur

YSI

YSI 58 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur