WIKA S-10 Manuel utilisateur
Operating instructions
Betriebsanleitung
Mode d'emploi
Manual de instrucciones
EN
DE
FR
ES
Druckmessumformer, Typ S-10
Pressure transmitter, model S-10
Pressure transmitter, model S-10
Transmetteur de pression, type S-10
Transmisor de presión, modelo S-10
2WIKA operating instructions pressure transmitter, model S-10
EN
DE
FR
1604457.16 09/2017 EN/DE/FR/ES
ES
© 2002 WIKA Alexander Wiegand SE & Co. KG
All rights reserved. / Alle Rechte vorbehalten.
WIKA®is a registered trademark in various countries.
WIKA®ist eine geschützte Marke in verschiedenen Ländern.
Prior to starting any work, read the operating instructions!
Keep for later use!
Vor Beginn aller Arbeiten Betriebsanleitung lesen!
Zum späteren Gebrauch aufbewahren!
Lire le mode d‘emploi avant de commencer toute opération !
A conserver pour une utilisation ultérieure !
¡Leer el manual de instrucciones antes de comenzar cualquier trabajo!
¡Guardar el manual para una eventual consulta!
Betriebsanleitung Typ S-10 Seite 27 - 50
Operating instructions model S-10 Page 3 - 26
Mode d‘emploi type S-10 Page 51 - 74
Manual de instrucciones modelo S-10 Página 75 - 99
EN
3WIKA operating instructions pressure transmitter, model S-10
1604457.16 09/2017 EN/DE/FR/ES
Contents
Declarations of conformity can be found online at www.wika.com
Contents
1. General information 4
2. Design and function 5
3. Safety 6
4. Transport, packaging and storage 8
5. Commissioning, operation 9
6. Adjustment of zero point and span 12
7. Faults 13
8. Maintenance and cleaning 15
9. Dismounting, return and disposal 16
10. Specications 18
EN
4WIKA operating instructions pressure transmitter, model S-10
1604457.16 09/2017 EN/DE/FR/ES
1. General information
1. General information
■
The instrument described in the operating instructions has been designed and manufactured using state-of-the-
art technology. All components are subject to stringent quality and environmental criteria during production. Our
management systems are certied to ISO 9001 and ISO 14001.
■
These operating instructions contain important information on handling the instrument.Working safely requires that
all safety instructions and work instructions are observed.
■
Observe the relevant local accident prevention regulations and general safety regulations for the instrument's range
of use.
■
The operating instructions are part of the product and must be kept in the immediate vicinity of the instrument and
readily accessible to skilled personnel at any time. Pass the operating instructions onto the next operator or owner of
the instrument.
■
Skilled personnel must have carefully read and understood the operating instructions prior to beginning any work.
■
The general terms and conditions contained in the sales documentation shall apply.
■
Subject to technical modications.
■
Further information:
- Internet address: www.wika.de / www.wika.com
- Relevant data sheet: PE 81.01
- Application consultant: Tel.: +49 9372 132-8976
Fax: +49 9372 132-8008976
EN
5WIKA operating instructions pressure transmitter, model S-10
1604457.16 09/2017 EN/DE/FR/ES
2. Design and function
2. Design and function
2.1 Overview
Electrical connection (depending on version)
Case; product label
Process connection, spanner flats
Process connection, thread
2.2 Scope of delivery
■
Pressure transmitter
■
Operating instructions
Cross-check scope of delivery with delivery note.
EN
6WIKA operating instructions pressure transmitter, model S-10
1604457.16 09/2017 EN/DE/FR/ES
3. Safety
3. Safety
3.1 Explanation of symbols
WARNING!
... indicates a potentially dangerous situation that can result in serious injury or death, if not avoided.
CAUTION!
... indicates a potentially dangerous situation that can result in light injuries or damage to equipment or
the environment, if not avoided.
Information
... points out useful tips, recommendations and information for ecient and trouble-free operation.
3.2 Intended use
The pressure transmitter is used for measuring pressure.The measured pressure is output as an electrical signal.
Only use the pressure transmitter in applications that lie within its technical performance limits (e.g. max. ambient
temperature, material compatibility, ...).The pressure transmitter is suitable for applications with pollution degree 3 and
an ambient temperature of -20 ... +80 °C.
→ For performance limits, see chapter 9 “Specications”.
The instrument has been designed and built solely for the intended use described here, and may only be used
accordingly.
The manufacturer shall not be liable for claims of any type based on operation contrary to the intended use.
EN
7WIKA operating instructions pressure transmitter, model S-10
1604457.16 09/2017 EN/DE/FR/ES
3. Safety
3.3 Personnelqualication
Skilled personnel
Skilled personnel, authorised by the operator, are understood to be personnel who, based on their technical training,
knowledge of measurement and control technology and on their experience and knowledge of country-specic
regulations, current standards and directives, are capable of carrying out the work described and independently
recognising potential hazards.
3.4 Labelling, safety marks
Product label
S# Serial no., P# Model code Accuracy
Power supply Pin assignment
Output signal
Measuring range
Symbols
Before mounting and commissioning the instrument, ensure you read the operating instructions!
EN
8WIKA operating instructions pressure transmitter, model S-10
1604457.16 09/2017 EN/DE/FR/ES
4. Transport, packaging and storage
4. Transport, packaging and storage
4.1 Transport
Check the pressure transmitter for any damage that may have been caused during transportation.
Obvious damage must be reported immediately.
4.2 Packaging and storage
Do not remove packaging until just before mounting.
Keep the packaging as it will provide optimum protection during transport (e.g. change in installation site, sending for
repair).
Permissible conditions at the place of storage:
■
Storage temperature: -40 ... +100 °C
■
Humidity: 45 ... 75 % relative humidity (no condensation)
EN
9WIKA operating instructions pressure transmitter, model S-10
1604457.16 09/2017 EN/DE/FR/ES
5. Commissioning, operation
5. Commissioning, operation
5.1 Mounting the instrument
Prior to commissioning, the pressure transmitter must be subjected to a visual inspection.
■
Leaking uid is indicative of damage.
■
Only use the pressure transmitter if it is in perfect condition with respect to safety.
Requirements for mounting point
The mounting point must meet the following conditions:
■
Ambience corresponds to a max. pollution degree of 3.
■
Humidity ≤ 80 % r. h. (non-condensing).
■
Protected from weather inuences.
■
Sealing faces are clean and undamaged.
■
Sucient space for a safe electrical installation.
■
For information on tapped holes and welding sockets, see Technical information IN 00.14 at www.wika.com.
■
Permissible ambient and medium temperatures remain within the performance limits. Consider possible restrictions
on the ambient temperature range caused by mating connector used.
→ For performance limits, see chapter 9 “Specications”
Sealing variants
Parallel threads
Seal the sealing face with a flat gasket, lens-type
sealing ring or WIKA profile sealing.
per EN 837 per DIN 3852-E
Tapered threads
Wrap threads with sealing material (e.g. PTFE
tape).
NPT, R and PT
EN
10 WIKA operating instructions pressure transmitter, model S-10
1604457.16 09/2017 EN/DE/FR/ES
Mounting the instrument
The max. torque depends on the mounting point (e.g. material and shape). If you have any questions,
please contact our application consultant.
→ For contact details, see chapter 1 “General information” or the back page of the operating instructions.
1. Seal the sealing face (→ see “Sealing variants”).
2
.
At the mounting point, screw the pressure transmitter in hand-tight.
3
.
Tighten with a torque spanner using the spanner ats.
5.2 Connecting the instrument to the electric system
Requirements for voltage supply
→ For power supply, see product label
The power supply for the pressure transmitter must be made via an energy-limited electrical circuit in accordance
with section 9.4 of UL/EN/IEC 61010-1, or an LPS per UL/EN/IEC 60950-1 / CSA C22.2 no. 60950-1, or class 2 in
accordance with UL1310/UL1585 (NEC or CEC). The voltage supply must be suitable for operation above 2,000 m
should the pressure transmitter be used at this altitude.
Requirements for electrical connection
■
Cable diameter matches the cable bushing of the mating connector.
■
Cable gland and seals of the mating connector are correctly seated.
■
With cable outlets, no humidity can ingress at the cable end.
Requirement for shielding and grounding
The pressure transmitter must be shielded and grounded in accordance with the grounding concept of the plant.
Connecting the instrument
1. Assemble the mating connector or cable outlet.
→ For pin assignments, see product label
2
.
Establish the plug connection.
5. Commissioning, operation
Autres manuels pour S-10
1
Table des matières
Langues :
Autres manuels WIKA Émetteur
WIKA
WIKA AC-1 Manuel utilisateur
WIKA
WIKA LH-20 Manuel utilisateur
WIKA
WIKA CPT-2 series Guide de l'utilisateur
WIKA
WIKA T24.10 Manuel utilisateur
WIKA
WIKA GDT-20 Manuel utilisateur
WIKA
WIKA UPT-2 Series Manuel utilisateur
WIKA
WIKA C-10 Manuel utilisateur
WIKA
WIKA SA-11 Manuel utilisateur
WIKA
WIKA E-10 Manuel utilisateur
WIKA
WIKA DPT-20 Manuel utilisateur
WIKA
WIKA air2guide A2G-50 Manuel utilisateur
WIKA
WIKA lh-10 Manuel utilisateur
WIKA
WIKA A-10 Manuel utilisateur
WIKA
WIKA ls-10 Manuel utilisateur
WIKA
WIKA MH-2 Manuel utilisateur
WIKA
WIKA CPT-2x series Manuel utilisateur
WIKA
WIKA F-20 Manuel utilisateur
WIKA
WIKA IS-10 Manuel utilisateur
WIKA
WIKA E-10 Manuel utilisateur
WIKA
WIKA F-20 Manuel utilisateur
Manuels Émetteur populaires d'autres marques
Dejero
Dejero EnGo 3x Manuel utilisateur
Rosemount
Rosemount 4600 Manuel utilisateur
Speaka Professional
Speaka Professional 2342740 Manuel utilisateur
trubomat
trubomat GAB 1000 Manuel utilisateur
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manuel utilisateur
Rondish
Rondish UT-11 Manuel utilisateur
