WeBoost DRIVE X FLEET Manuel utilisateur

PROFESSIONAL VEHICLE CELL

SIGNAL BOOSTER KIT

DRIVE X FLEET

A WILSON ELECTRONICS BRAND

NEED HELP? support.weboost.com

Use our weBoost App to guide you through the installation.

See inside page for more details.

1-866-294-1660

Installation Guide

Download the weBoost App

Use our app to guide you through setting up a weBoost cell phone

signal booster in your home, business, or vehicle. Boost every

network, including 5G, right away.

Download the weBoost App

Videos to guide you

through installation

Antenna positioning guide

for optimal performance

Before and after cell

signal readings

______

Index

Package Contents 1

STEP 1: Drill Cable Entry Hole To Your Vehicle 2

STEP 2: Mount NMO Outside Antenna 5

STEP 3: Mount In-Vehicle Antenna 6

STEP 4: Wire The Power Supply 7

STEP 5: Connect Coax Cables To Booster 8

STEP 6: Connect Power Supply To Booster 9

Light Patterns 10

Troubleshooting 11

Safety Guidelines 13

Speciﬁcations 14

Warranty 15

1PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT DRIVE X FLEET

________

Package

Contents

Drive X

Booster

& Bracket

Outside NMO

Antenna +

Connector

Mounting Cable

In-Vehicle

Antenna Power

Supply

Optional Antenna

Extension Cable Protective Tape

For Installation O-Ring Lubricant

Packet

DRIVE X FLEET PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT 2

______

Step 1: Drill Cable Entry Hole

To Your Vehicle

Identify a location for NMO outside antenna on the

top of your vehicle that is:

 Near the center of the roof

 At least 12 inches away from any other antennas

 At least 12 inches away from any windows

(for best performance install on top of vehicle)

Do a ‘soft install’ before drilling the hole for the

cable entry.

Set up the system by routing the cable through

an open door or window, completing the setup

instructions, verifying the system works as desired,

and then drilling the hole.

12 in. away from windows

(including sunroofs)

Good NMO Outside

Antenna Placement

3PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT DRIVE X FLEET

Place the protective tape on the

vehicle in the desired location.

Using a 3/4” hole saw, drill a

hole in the center of the

protective tape.

______

(STEP 1 cont.)

After completing the ‘soft install’ and identifying NMO

outside antenna location:

protective tape

vehicle surface

protective tape

3/4” bit

DRIVE X FLEET PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT 4

apply silicone grease

After hole has been drilled, insert NMO Mounting Cable

through (SMA connector end ﬁrst) and remove collar.

Position threads of the cable mount above vehicle surface.

Apply included silicone grease to the o-ring on the collar

then screw the collar to the base mount. Ensure the mount is

centered in the hole and tighten with wrench.

screw collar

to base mount

For a professional installation, we recommend routing the cable

under the headliner and down through the side trim panel to

the desired booster location on the ﬂoor of the vehicle.

side trim panel

headliner

remove

collar

insert through hole

______

(STEP 1 cont.)

5PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT DRIVE X FLEET

Before attaching the antenna, apply a thin layer of silicone

grease to the threads, only, to the NMO mount and to the

o-ring on the antenna. Screw the antenna onto the NMO

mount and hand tighten into place.

hand tighten and make sure

gasket is touching vehicle

surface

screw on

NMO Antenna

______

Step 2: Mount NMO

Outside Antenna

apply silicone grease

NOTE: DO NOT apply silicone grease to the antenna pin contact surface.

DRIVE X FLEET PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT 6

The location should be at least 18 inches but no more than

36 inches from where the cell phone device will be used.

Adhesive and Velcro® mounting options are included.

In-Vehicle Antenna

Identify a place to mount the in-vehicle antenna, either on

the side of the seat or on the dash and mount.

______

Step 3: Mount In-Vehicle

Antenna

clean surface of dash before attaching

adhesive strip

dash option

seat option

In-Vehicle

Antenna

7PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT DRIVE X FLEET

Before connecting the power supply, disconnect the vehicle battery

leads to avoid any electrical shocks during installation.

Locate a place where cables are already running through the ﬁrewall

(rear wall of engine bay) to the inside of the cabin.

Locate the same ﬁrewall hole from inside of the vehicle cabin.

Route the power cables of the power supply from the inside of the

vehicle cabin out through ﬁrewall hole.

Note: The cables must be routed inside to outside since the power

supply brick won’t ﬁt through the ﬁrewall holes. The power supply

brick should remain inside the vehicle cabin.

Connect the positive lead of the power supply (lead with red tape)

to the disconnected positive (+) lead of the battery (not the positive

terminal on the battery itself).

Connect the negative lead of the power supply (lead without tape)

to the disconnected negative (-) lead of the battery (not the negative

terminal on the battery itself).

Connect the positive (+) lead back to the vehicle battery.

Connect the negative (-) lead back to the vehicle battery.

Use steps below as a draft/template of the general install of

the power supply.

______

Step 4: Wire The Power

Supply

NOTE: Having the power supply directly connected to the battery may

drain the battery’s life. Please review the vehicle’s owner’s manual for more

information. Adding a “fuse tap” may be another solution. A “fuse tap” is an

electrical part that functions as a power splitter and is meant to be installed

in the car’s fuse box, making the amp shut o when the vehicle’s ignition

switch is turned o.

Table des matières

Autres manuels weBoost Extenseur

weBoost

weBoost DRIVE REACH OTR FLEET Manuel utilisateur

weBoost

weBoost Basic Home Manuel utilisateur

weBoost

weBoost Home 4G Manuel utilisateur

weBoost

weBoost Drive 4G-S Manuel utilisateur

weBoost

weBoost drive 3G-M Manuel utilisateur

weBoost

weBoost DRIVE 4G-X RV Manuel utilisateur

weBoost

weBoost Home MultiRoom 650144 Manuel utilisateur

weBoost

weBoost Drive AM100-Pro Manuel utilisateur

weBoost

weBoost DRIVE 4G-X FLEET Manuel utilisateur

weBoost

weBoost Drive AS100 Manuel utilisateur

weBoost

weBoost Home Complete 460045 Manuel utilisateur

weBoost

weBoost Drive 4G-M Manuel utilisateur

weBoost

weBoost DRIVE 4G-X FLEET Manuel utilisateur

weBoost

weBoost 470001 Manuel utilisateur

weBoost

weBoost DRIVE SLEEK U470035 Manuel utilisateur

weBoost

weBoost Drive Reach RV Manuel utilisateur

weBoost

weBoost smartech III 472005 Manuel utilisateur

weBoost

weBoost DRIVE 4G-X FLEET Manuel utilisateur

weBoost

weBoost eqo Manuel utilisateur

weBoost

weBoost Drive 3G-Flex 470013 Manuel utilisateur

weBoost

weBoost 460059 Manuel utilisateur

weBoost

weBoost DRIVE 4G-X OTR Manuel utilisateur

weBoost

weBoost Destination RV Manuel utilisateur

weBoost

weBoost Drive 4G-M Manuel utilisateur

Manuels Extenseur populaires d'autres marques

SY HDBT-60T Manuel utilisateur

Appsys ProAudio

Appsys ProAudio ADX-16 Manuel utilisateur

Atlona

Atlona RS232 Manuel utilisateur

IDK

IDK OPF-TH1000-A Manuel utilisateur

Enable-IT

Enable-IT 824WP Manuel utilisateur

Worx

Worx Landroid RadioLink WA0864 Fiche technique

TP-Link

TP-Link TL-WA730RE Manuel utilisateur

Camplex

Camplex CMX-HDMI-SFPL Manuel utilisateur

SC&T

SC&T HE03-4K Manuel utilisateur

Marmitek

Marmitek MegaView70 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Foxun

Foxun SX-GES24 Manuel utilisateur

MuxLab

MuxLab 500771 Manuel utilisateur

foxunhd

foxunhd SX-AEX01 Manuel utilisateur

TERK Technologies

TERK Technologies LFIRX2 Manuel utilisateur

Devolo

Devolo Audio Extender Manuel

Edimax

Edimax EW-7438RPn V2 Manuel utilisateur

Shinybow USA

Shinybow USA SB-6335T5 Manuel utilisateur

weBoost DRIVE X FLEET Manuel utilisateur

Manuels Extenseur populaires d'autres marques