Wali GSDM001-P Manuel utilisateur

Autres manuels Wali Support et étagère

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur

[email protected]

75x75/100x100 35"

MAX

2-12kg

(4.4-26.

4lbs)

RATED

GSDM001-P

INSTALLATION MANUAL

Single Monitor Desk Mount

2

A (x1)

VESA Plate

B (x1)

Pole

C (x1) D (x1)

E (x1) F (x1) G (x1)

Bolt

H (x1)

I (x1) J (x1) K (x1)

Spring Washer

L (x1)

M6X16 Bolt

M (x3)

M6X12 Bolt

N (x3)

M6X10 Bolt

O (x2)

M5X12 Bolt

M-B (x4)

D5 Washer

M-C (x4)

P (x4)

Wire Clip

Q (x1)

4mm Allen Key

R (x1)

6mm Allen Key

S (x1)

Wrench

T (x1)

Base

C-Clamp

Cover

Grommet Base Plate Nut

Anti-skid Pad

M4X12 Bolt

M-A (x4)

Support Plate

Supplied Parts List

3

Arm

C-clamp Brace

R

N

E

R

P

4

Step 2

Fit clamp: 0.4”-3.3”

Grommet: 0.4”-3.3“

Step 1

Option A

D

D

Clamp Installation

1. Connect Pole and Base from the bottom using M6X16 Bolt and tighten with 4mm Allen Key .

D

E

C

C

M

R

2. Connect Base and C-clamp Brace using M6x12 Bolt and tighten with 4mm Allen Key . Tear off the

protective paper to attach Anti-Skid Pad to the bottom designated position of Base as image shown.

DENR

PD

R

M

M

D

RO

or

G

O

5

4. Rotate the hand knob clockwise to fasten for stability. Attach the Cover to the C-Clamp.

G

FO

R

3. Select the preferred height firstly and connect C-Clamp to C-Clamp Brace using M6x10 Bolt and tighten

with 4mm Allen Key

.E

2’’-3.3’’

0.4’’-2.2’’

R

Hand Knob

F

F

F

F

EE

Option B

Grommet Base Installation

I

H

N

R

P

0.4’’-3.3’’

0.4’’-3.3’’

ø 10mm

(ø ")3/8

D

N

R

If the existing grommet hole comes with a plastic

protector, remove it to ensure a flat surface before

installing the desk mount.

P

D

2. Tear off the protective paper to attach Anti-Skid Pad to the

bottom designated position of Base as image shown.

1.Guide Grommet Base Plate through Bolt

and connect them to Base from the bottom

using M6x12 Bolt and tighten with 4mm Allen

Key . I

IH

D

6

3a.Existing Grommet Hole Installation 3b.Self-drilled Grommet Hole Installation

Mark the position of the hole on your mounting surface. Drill

a 3/8"(10mm) diameter hole at the marked position through

the mounting surface.

D

S

Q

A

Step 3

T

K

L

J

Put the Arm and Wire Clip through the Pole , adjust the preferred height and tighten using 6mm Allen Key .

AQCS

H

J

L

K

K

4. Insert the assembled pole through the desk hole, guide the Support Plate , Washer and Nut through the

Bolt , rotate the Nut clockwise to fasten for stability.

7

A

Select M4x12 Bolt or M5x12 Bolt

according

to your TV/Monitor,connect VESA Plate together

with D5 Washer

into the mounting holes on the

back of TV/Monitor, tighten with screwdriver.

(Screwdriver needed but not included)

M-A M-B

B

M-C

BM-A

M-B

M-C

M-C

8

Step 4

Step 5

Step 4.1

M4 M5

Only one screw size fits your Monitor

Hand thread screws into the

threaded inserts on the back

of your Monitor to determine

which screw (M4or M5) to

use.

Step 4.2

Select Monitor Screws

Step 4.1

Step 4.2

Pull the buckle and put the assembled TV/Monitor onto the Arm and ensure stability.

S

9

Step 6

To properly balance the arm with monitors mounted, adjust the spring tension with 6mm Allen Key .

First, position and firmly hold the arm horizontally as

shown. Ask for assistance should you require it. If the arm drops, turn the adjustment screw

counter-clockwise until it stays in a horizontal

position.

To avoid damage to monitors or mount,

always keep the arm in a horizontal

position while making adjustments.

Again, ask for assistance if required.

If the arm rises, turn the adjustment screw

clockwise until it stays in a horizontal

position.

DO NOT over tighten the screws.

10

Step 7

Guide the cable through the cable slot.