Viessmann Vitorond 200 Series Mode d'emploi
Service instructions
for contractors
VIESMANN
Vitorond 200
Type VD2, 320 to 1080 kW
Oil/gas boiler
VITOROND 200
5692517 GB 9/2018 Please keep safe.
2
Please follow these safety instructions closely to
prevent accidents and material losses.
Safety instructions explained
Danger
This symbol warns against the risk of injury.
!Please note
This symbol warns against the risk of material
losses and environmental pollution.
Note
Details identified by the word "Note" contain additional
information.
Target group
These instructions are exclusively intended for quali-
fied contractors.
■Work on gas installations may only be carried out by
a registered gas fitter.
■Work on electrical equipment may only be carried
out by a qualified electrician.
■The system must be commissioned by the system
installer or a qualified person authorised by the
installer.
Regulations to be observed
■National installation regulations
■Statutory regulations for the prevention of accidents
■Statutory regulations for environmental protection
■Codes of practice of the relevant trade associations
■All current safety regulations as defined by DIN, EN,
DVGW, TRGI, TRF, VDE and all locally applicable
standards
aÖNORM, EN, ÖVGW G K directives,
ÖVGW-TRF and ÖVE
cSEV, SUVA, SVGW, SVTI, SWKI, VKF and
EKAS guideline 1942: LPG, part 2
Safety instructions for working on the system
Working on the system
■Where gas is used as the fuel, close the main gas
shut-off valve and safeguard it against unintentional
reopening.
■Isolate the system from the power supply, e.g. by
removing the separate fuse or by means of a mains
isolator, and check that it is no longer live.
■Safeguard the system against reconnection.
■Wear suitable personal protective equipment when
carrying out any work.
Danger
Hot surfaces and fluids can lead to burns or
scalding.
■Before maintenance and service work, switch
OFF the appliance and let it cool down.
■Never touch hot surfaces on the boiler, burner,
flue system or pipework.
!Please note
Electronic assemblies can be damaged by elec-
trostatic discharge.
Prior to commencing work, touch earthed
objects such as heating or water pipes to dis-
charge static loads.
Repair work
!Please note
Repairing components that fulfil a safety func-
tion can compromise the safe operation of the
system.
Replace faulty components only with genuine
Viessmann spare parts.
Safety instructions
Safety instructions
5692517
3
Auxiliary components, spare and wearing parts
!Please note
Spare and wearing parts that have not been tes-
ted together with the system can compromise its
function. Installing non-authorised components
and making non-approved modifications or con-
versions can compromise safety and may inva-
lidate our warranty.
For replacements, use only original spare parts
supplied or approved by Viessmann.
Safety instructions for operating the system
If you smell gas
Danger
Escaping gas can lead to explosions which may
result in serious injury.
■Do not smoke. Prevent naked flames and
sparks. Never switch lights or electrical appli-
ances on or off.
■Close the gas shut-off valve.
■Open windows and doors.
■Evacuate any people from the danger zone.
■Notify your gas or electricity supply utility from
outside the building.
■Have the power supply to the building shut off
from a safe place (outside the building).
If you smell flue gas
Danger
Flue gas can lead to life threatening poisoning.
■Shut down the heating system.
■Ventilate the installation site.
■Close doors to living spaces to prevent flue
gases from spreading.
What to do if water escapes from the appliance
Danger
If water escapes from the appliance there is a
risk of electrocution.
Switch OFF the heating system at the external
isolator (e.g. fuse box, domestic distribution
board).
Danger
If water escapes from the appliance there is a
risk of scalding.
Never touch hot heating water.
Condensate
Danger
Contact with condensate can be harmful to
health.
Never let condensate touch your skin or eyes
and do not swallow it.
Flue systems and combustion air
Ensure that flue systems are clear and cannot be
sealed, for instance due to accumulation of conden-
sate or other external causes.
Avoid continuous condensate disposal with a wind pro-
tector.
Ensure an adequate supply of combustion air.
Inform system users that subsequent modifications to
the building characteristics are not permissible (e.g.
cable/pipework routing, cladding or partitions).
Danger
Leaking or blocked flue systems, or an inade-
quate supply of combustion air can cause life
threatening poisoning from carbon monoxide in
the flue gas.
Ensure the flue system is in good working order.
Vents for supplying combustion air must be non-
sealable.
Extractors
Operating appliances that exhaust air to the outside
(extractor hoods, extractors, air conditioning units, etc.)
can create negative pressure. If the boiler is operated
at the same time, this can lead to a reverse flow of flue
gas.
Danger
The simultaneous operation of the boiler and
appliances that exhausts air to the outside can
result in life threatening poisoning due to a
reverse flow of flue gas.
Fit an interlock circuit or take suitable steps to
ensure an adequate supply of combustion air.
Safety instructions
Safety instructions (cont.)
5692517
4
1. Information Symbols ................................................................................................. 5
Intended use .......................................................................................... 5
Product information ................................................................................ 6
2. Commissioning, inspec-
tion, maintenance
Steps - commissioning, inspection and maintenance ............................ 7
3. Parts lists Ordering parts ........................................................................................ 15
Boiler door ............................................................................................. 16
Boiler sections ....................................................................................... 18
Back of boiler ......................................................................................... 20
Flange elements .................................................................................... 22
Thermal insulation, casing ..................................................................... 24
Thermal insulation, casing ..................................................................... 26
4. Layout of panels and ther-
mal insulation
................................................................................................................ 28
5. Water quality Water quality requirements .................................................................... 32
■Prevention of damage due to scaling ................................................. 32
■Prevention of damage due to corrosion on the water side ................. 33
6. Commissioning/service
reports
Fill and top-up water table ..................................................................... 34
Maintenance/service .............................................................................. 34
7. Specification ................................................................................................................ 36
8. Final decommissioning Final decommissioning and disposal ..................................................... 38
9. Certificates EU Declaration of Conformity ................................................................ 39
Manufacturer's certificate according to the 1st BImSchV ...................... 39
10. Keyword index ................................................................................................................ 40
Index
Index
5692517
5
Symbol Meaning
Reference to other document containing
further information
1.
Step in a diagram:
The numbers correspond to the order in
which the steps are carried out.
Warning of material losses and environ-
mental pollution
Live electrical area
Pay particular attention.
■Component must audibly click into place.
or
■Acoustic signal
■Fit new component.
or
■In conjunction with a tool: Clean the sur-
face.
Dispose of component correctly.
Dispose of component at a suitable collec-
tion point. Do not dispose of component in
domestic waste.
The steps in connection with commissioning, inspec-
tion and maintenance are found in the "Commission-
ing, inspection and maintenance" section and identified
as follows:
Symbol Meaning
Steps required during commissioning
Not required during commissioning
Steps required during inspection
Not required during inspection
Steps required during maintenance
Not required during maintenance
Intended use
The appliance is only intended to be installed and
operated in sealed unvented heating systems that
comply with EN 12828, with due attention paid to the
associated installation, service and operating instruc-
tions as well as the details in the datasheet.
It is only designed for the heating up of heating water.
Commercial or industrial usage for a purpose other
than the heating up of heating water shall be deemed
inappropriate.
Intended use presupposes that a fixed installation in
conjunction with permissible components designed for
this purpose has been carried out.
Every other use will be deemed to be inappropriate.
Any resulting losses are excluded from the manufac-
turer's liability.
Any usage beyond this must be approved by the man-
ufacturer for the individual case.
Intended use also includes the adherence to mainte-
nance and inspection intervals.
Information
Symbols
5692517
Information
6
Vitorond 200, type VD2
■Fuels: Fuel oil and natural gas
■Permissible operating pressure 6 bar (0.6 MPa)
■Rated heating output 320 to 1080 kW
Information
Product information
5692517
Information
7
Commissioning steps
Inspection steps
Maintenance steps Page
• • 1. Commissioning the system............................................................................................... 8
•2. Shutting down the system
•3. Opening the boiler door and cleaning cover................................................................... 8
•4. Withdrawing and cleaning the turbulators...................................................................... 9
•5. Cleaning the heating surface, flue outlet and flue.......................................................... 10
• • 6. Checking all gaskets and packing cords on the flue gas side
•7. Checking the thermal insulation components on the boiler door................................. 10
•8. Inserting the turbulators, fitting the boiler door and cleaning cover............................ 10
• • 9. Checking all connections on the heating water side and the sensor well for leaks
• • 10. Checking the function of the safety equipment
••• 11. Checking the pressure switch function........................................................................... 11
••• 12. Checking the temperature controller setting if a building management system is
used (DCC system)............................................................................................................ 12
• • 13. Checking the expansion vessel and system pressure................................................... 12
•14. Checking the firm seating of electrical plug-in connections and cable grommets
•15. Checking the thermal insulation
• • 16. Checking the water quality................................................................................................ 12
• • 17. Cleaning the sight glass in the boiler door...................................................................... 13
•18. Checking the mixer for ease of operation and tightness............................................... 13
•19. Checking the function of the return temperature raising facility (if installed)
• • 20. Checking the installation room ventilation
• • 21. Checking the flue pipe for tightness
•22. Adjusting the burner.......................................................................................................... 13
•23. Instructing the system user.............................................................................................. 14
•24. Operating and service documents................................................................................... 14
Commissioning, inspection, maintenance
Steps - commissioning, inspection and maintenance
5692517
8
Operating and service instructions for the control
unit and the burner
01. Close the gas shut-off valve and open the boiler
door.
02. Check that the turbulators are fully inserted into
the hot gas flues (see page 10); open the boiler
door for this.
03. Check that the ventilation air aperture in the instal-
lation room is open.
04. Fill the heating system with water and vent the
system.
Permissible operating pressure: 6 bar (0.6 MPa)
!Please note
Scaling may result if the system is not oper-
ated with fully softened heating water.
Observe the instructions in chapter "Water
quality requirements".
05. Enter the amount of fill water and water hardness
into the table in the appendix on page 34.
06. Check the system pressure.
07. Check the oil level or the gas supply pressure.
08. Open the flue gas damper (if installed).
09. Check that the cleaning apertures on the flue out-
let are closed.
10. Open the shut-off valves in the oil or gas line.
11. Switch ON the mains isolator, the switch for the
heating circuit pump and the burner ON/OFF
switch in this order (observe the burner manufac-
turer's instructions).
12. The dew point range must be cleared as quickly
as possible. To do so, prevent any heat supply to
the consumers when heating the system from
cold. This also applies when restarting after main-
tenance and cleaning work.
13. Once the flow temperature has been reached,
successively switch on the heat consumers.
Switch the burner over to automatic mode.
14. Check all gaskets and plugs, and retighten if nec-
essary.
15. Check the boiler door and cleaning cover after
approx. 50 hours run and retighten all screws.
Danger
There is a risk of injury when working on pres-
surised components.
Only open the connections on the heating water
side after the boiler has been depressurised.
!Please note
Negative pressure in the boiler can cause mate-
rial damage.
Only drain the boiler with a suction pump when
the air vent valve is open.
Note
When commissioning the heating system, scaling in
the boiler can be influenced by the way the heating
system is started.
Start the boiler with a low heating output or slow heat-
ing up in stages. This results in scaling over the entire
heating surface, not predominantly on the walls with
the greatest thermal density.
For multi boiler systems, commission all boilers
simultaneously. Where only one boiler in a multi
boiler system is commissioned, the entire scaling (cal-
cium content) would be concentrated on the heating
surface of that one boiler only.
If commissioning with only one boiler cannot be avoi-
ded, the maximum fill and top-up water volume is
determined only on the heating output of the one
boiler.
No further steps are required if the heating system is
filled with fully softened heating water.
Shutting down the system
Opening the boiler door and cleaning cover
Note
On gas burners, disconnect the gas supply pipe.
Commissioning, inspection, maintenance
Commissioning the system
5692517
9
Fig. 1
Withdrawing and cleaning the turbulators
A
Fig. 2
AOnly up to 860 kW
Commissioning, inspection, maintenance
Opening the boiler door and cleaning cover (cont.)
5692517
10
C
A B
Fig. 3
1. Clean flues A and combustion chamber B with
the brushes.
Clean the spaces in between and the fins with the
narrow side of the brush.
Remove combustion residues with a vacuum
cleaner.
2. Remove combustion residues from the flue and the
flue outlet through the cleaning apertures in flue
outlet C using a vacuum cleaner.
Checking all gaskets and packing cords on the flue gas side
Checking the thermal insulation components on the boiler door
Danger
When working with high temperature insulation
materials that contain zirconium or aluminium
silicate ceramic fibres, fibre dust may
develop. This fibre dust can be harmful to
health.
Only trained personnel may adjust or replace
the insulation. Wear suitable protective clothing,
especially breathing equipment and safety gog-
gles.
Inserting the turbulators, fitting the boiler door and cleaning cover
Note
On gas burners, mount the gas supply pipe.
Danger
Escaping gas leads to a risk of explosion.
Check all gas connections for tightness.
Commissioning, inspection, maintenance
Cleaning the heating surface, flue outlet and flue
5692517
Autres manuels pour Vitorond 200 Series
1
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Viessmann Chaudière
Viessmann
Viessmann Vitoplus 300 Mode d'emploi
Viessmann
Viessmann VITOLADENS 300-W Mode d'emploi
Viessmann
Viessmann B2HA 19 Manuel utilisateur
Viessmann
Viessmann Vitocell 200 Cylinder Guide de l'utilisateur
Viessmann
Viessmann VITOCELL 100-U Manuel utilisateur
Viessmann
Viessmann VITODENS 050-W Manuel utilisateur
Viessmann
Viessmann Vitoladens 300-C Mode d'emploi
Viessmann
Viessmann Vitocell 100-E Guide rapide
Viessmann
Viessmann VITORONDENS 200-T Mode d'emploi
Viessmann
Viessmann Vitodens 222-F B2TB Guide de l'utilisateur
Viessmann
Viessmann VITOLIGNO 300-P Mode d'emploi
Viessmann
Viessmann VITODENS 333 WS3A Manuel utilisateur
Viessmann
Viessmann VITOCELL 100-B Mode d'emploi
Viessmann
Viessmann Vitoladens 300-C Mode d'emploi
Viessmann
Viessmann Vitodens 100-W B1HA Manuel d'instructions
Viessmann
Viessmann Vitodens 100-W WB1B Series Guide rapide
Viessmann
Viessmann Vitoplex 100 PV1 Mode d'emploi
Viessmann
Viessmann Vitola 200 Manuel utilisateur
Viessmann
Viessmann Vitotron 100 Series Manuel utilisateur
Viessmann
Viessmann VITOCELL 100-U Mode d'emploi
Manuels Chaudière populaires d'autres marques
Vaillant
Vaillant uniSTOR VIH SW GB 500 BES Manuel utilisateur
Radijator
Radijator BIO max 23.1 Manuel utilisateur
Brunner
Brunner BSV 20 Manuel utilisateur
Buderus
Buderus Logamax GB062-24 KDE H V2 Manuel utilisateur
Potterton
Potterton 50e Fiche technique
UTICA BOILERS
UTICA BOILERS TriFire Manuel utilisateur
