VEVOR 3 IN 1/305 Manuel utilisateur
Technical Support and E-Warranty Certificate www.vevor.com/support
THE SHEAR / BRAKE / ROLL
OPERATION MANUAL
MODEL:3 IN 1/305
We continue to be committed to provide you tools with competitive price.
"Save Half", "Half Price" or any other similar expressions used by us only represents an
estimate of savings you might benefit from buying certain tools with us compared to the major
top brands and doses not necessarily mean to cover all categories of tools offered by us. You
are kindly reminded to verify carefully when you are placing an order with us if you are
actually saving half in comparison with the top major brands.
- 1 -
MODEL:3 IN 1/305
Have product questions? Need technical support? Please feel free to
contact us:
Technical Support and E-Warranty Certificate
www.vevor.com/support
NEED HELP? CONTACT US!
This is the original instruction, please read all manual instructions
carefully before operating. VEVOR reserves a clear interpretation of our
user manual. The appearance of the product shall be subject to the
product you received. Please forgive us that we won't inform you again if
there are any technology or software updates on our product.
THE SHEAR / BRAKE /
ROLL
- 2 -
Warning-To reduce the risk of injury, user must read
instructions manual carefully.
SPECIFICATIONS
Model.............................................................................................3 in 1/305
Effective Width...............................................305mm (12 inches) Maximum
Shearing Thickness….........................................................1mm (20 gauge)
Bending Thickness……......................................................1mm (20 gauge)
BendingAngle...............90° Rolling thickness……...........…1mm (20 gauge)
Roll Diameter……....................................................….45mm (1-1/2 inches)
Standard accessories
UNPACKING
The SHEAR / BRAKE / ROLL 3-IN-1/12 is shipped from the manufacturer
in a carefully packed carton box. Thoroughly inspect the product upon
opening the package. After unpacking the unit, carefully inspect for any
damage that may have occurred during transit.If damage has occurred,
shipping damage claims must be filed with the carrier and are the
responsibility of the user. Check for completeness. Immediately report
missing parts to dealer.
1
Roller adjustment bolt
2
2
Fixed knob bolt
2
3
Rocker assembly
1
4
Guide rod assembly
2
5
Baffle
2
- 3 -
Warning
The warnings, cautions and instructions discussed in this instructions
or situations that could occur. It must be understood by the operator
that common sense and caution are factors that cannot be built into
this product, but must be supplied by the operator.
SAVE THESE INSTRUCTIONS
Thank you for purchasing 12-inch Shear/Brake/Roll machine. Before
attempting to operate your new tool please read these instructions
thoroughly. You will need these instructions for the safety warnings,
precautions, assembly, operation, maintenance procedures, parts list and
diagrams. Keep your invoice number with these instructions. Write the
invoice number on the inside of front cover. Keep the instructions and
invoice in a safe, dry place for future reference.
SAFETY RULES
1. Know your machine. Read this manual carefully. Learn the machine’s
applications and limitations, as well as specific potential hazards peculiar
to it.
2. Keep work area clean and well lit. Cluttered or dark work areas invite
accidents.
3. Keep Children away. All children should be kept away from the work
area. Never let a child handle a tool without strict adult supervision.
4. Do not operate this tool if under the influence of alcohol or drugs. Read
warning labels on prescriptions to determine if your judgment or reflexes
are impaired while taking drugs. If there is any doubt, do not attempt to
operate.
5. Use safety equipment. Eye protection should always be worn when
operating this machine. Use ANSI approved safety glasses. Everyday
eyeglasses only have impact resistant lenses. They are NOT safety
glasses. Dust masks, non-skid safety shoes, hard hat, or hearing
- 4 -
protection should be used in appropriate conditions.
6. Wear proper apparel. Loose clothing, gloves, neckties, rings, bracelets,
or other jewelry may present a potential hazard when operating this
machine. Please keep all apparel clear of the machine.
7. Don’t overreach. Keep proper footing and balance always when
operating this product.
8. Check for damage. Check your tool regularly. If part of the tool is
damaged it should be carefully inspected to make sure that it can perform
its’ intended function correctly. If in doubt, the part should be repaired.
Refer all servicing to a qualified technician. Consult your dealer for advice.
9. Maintain tools with care. Keep tools sharp and clean. Properly
maintained tools, with sharp cutting edges, are less likely to bind and are
easier to control.
10. When you move, install, clean or adjust the machine, keep away from
the shears.
11. Put down the protective cover when you don’t use the sliding roll of the
machine.
12. Keep your hands away from the die when you are working on it.
- 5 -
SET-UP AND ASSEMBLY
Floor Diagrams
Figure 1 – hole centers for Shear, Brake and Roll
Assembly
Tools required for setup and assembly:5, 6mm hex keys (“Allen
wrenches”)16mm open end wrench.
1. Take out machine and spare parts from box.
2. Carefully clean all rust protected surfaces with a mild solvent or
kerosene and a soft rag. Do not use lacquer thinner, paint thinner, or
gasoline, as these may damage painted surfaces.
3. Coat all machined surfaces with a very light film of oil to inhibit rust.
4. Carefully move machine to a workbench or stand. Machine location
must allow free access on all sides.
5. Bolt machine to stand or workbench. The stand or workbench must be
bolted to the floor. (NOTE: An optional stand is available for this machine;
see Section 8. Contact KAKA distributor to order.)
- 6 -
6. Remove one handle (A, Figure 2) from each operating handle assembly,
using 6mm hex key.
Figure 2
7. Loosen lock bolt (C, Figure 2).
8. Slide bar (B) into hub and tighten lock bolt (C) to secure.
9. Re-install handle (A).
10. Install both guide rods into either the upper or lower set of threaded
holes(Figures 3 & 4) and tighten the setting by rotating hex nut against the
cast base of the machine with 16mm wrench.
11. Install guide plate as shown in Figures3 or 4. Secure it to rods using the
T-handles.
Figure 3 (Brake position) Figure 4 (Shear position)
NOTE: For brake operation, install guide rods into upper set of holes
(Figure 3); for shear operation, install them in lower set of holes (Figure 4).
- 7 -
PRESS BRAKE SET-UP
Do not bend material larger than 12” 20-gauge mild steel.
Failure to comply may cause serious injury and/or damage to the
machine.
To set up for bending:
1. Place a strip of wood (F, Figure 5) on bottom die, the full length of die.
2. Close brake until the wood contact supper dies(E).
3. Loosen screws (D) using 5mm hex key.
Figure 5
4. Select upper dies (E) for desired job and remove the others by sliding
them out the left end.（Included die set sizes1”x1, 2”x2, 3”x1, 4”x1）
5. Move operating handle until the wood pushes up the dies so that they
seat uniformly in upper beam.
6. Securely re-tighten all screws (Figure3), then release and remove wood
strip.
7. If making repeated bends or using along workpiece, position guide rods
and plate for brake operation, as shown in Figure 3.
8. Scribe a line on workpiece for bend location. (Be sure to accommodate
bend allowance based on thickness of material. This can be done either
- 8 -
through trial and error, or by consulting a machinist’s handbook.)
9. Rest workpiece on v-block (lower die)so that the scribed line is aligned
with the tips of upper die(s).
10. Hold workpiece steady and use operating handle to make bend.
To adjust brake beam (G, Figure 6) for90° bends at bottom of stroke:
1. Slightly loosen locking screws (H)using 6mm hex key.
2. Turn brake beam adjusting screws (G)with 16mm wrench, until test
bend reflects 90° bend at both ends of brake.
3. Re-tighten screws (H).
Figure 6
For special repetitive bends, the brake beam may be adjusted to over-bend
the desired angle since the metal will have some degree of “spring back”.
Shear set-up
Do not shear material larger than 12” 20 gauge mild steel.
Failure to comply may cause serious injury and/or damage to the
machine.
1. Install guide rods and plate in shear position (Figure 4) and adjust to
desired length of workpiece cut.
2. Place workpiece against guide block at right edge of table (K, Figure 7).
Table des matières
Autres manuels VEVOR Outils
VEVOR
VEVOR XRSS2305 Manuel utilisateur
VEVOR
VEVOR JT-1632 Manuel utilisateur
VEVOR
VEVOR CB07 Manuel utilisateur
VEVOR
VEVOR JK601 Manuel utilisateur
VEVOR
VEVOR HKB1040A Manuel utilisateur
VEVOR
VEVOR XF-E004A-2 Manuel utilisateur
VEVOR
VEVOR 5609 Manuel utilisateur
VEVOR
VEVOR 19985-SN Manuel utilisateur
VEVOR
VEVOR CT-612 Manuel utilisateur
VEVOR
VEVOR SW-WP003 Manuel utilisateur
VEVOR
VEVOR KT1106A Manuel utilisateur
VEVOR
VEVOR JH-0840 Manuel utilisateur
VEVOR
VEVOR FTC5220 Manuel utilisateur
VEVOR
VEVOR JY-SS2L Manuel utilisateur
VEVOR
VEVOR KT1103A Manuel utilisateur
VEVOR
VEVOR XRSS2304 Manuel utilisateur
VEVOR
VEVOR WK3552E-5 Manuel utilisateur
VEVOR
VEVOR LD-868 Manuel utilisateur
VEVOR
VEVOR KH2000B Manuel utilisateur
VEVOR
VEVOR 9526 Manuel utilisateur
