Vertiv Liebert APS Manuel utilisateur

590-1563-501A/SL-55016_REV1_3-17

LIEBERT® APS™

MODULE REPLACEMENT

Quick Installation Guide

These instructions apply to the

replacement or addition of the

following modules:

• Power module

• Battery module

• Charger module

• System control module

• System monitoring module

BATTERY, POWER, AND

CHARGER MODULE

REMOVAL

WARNING

Risk of heavy unit

falling over. Can cause equipment

damage, injury or death. Read all of the

instructions before attempting to move,

lift, remove packaging, or prepare the

unit for installation. The UPS represents

a tipping hazard.

Do not remove more than one module

at a time. Failure to do so may cause

unit to tip over and cause serious injury.

To locate a faulty module, remove the

bezel cover and look for an illuminated

yellow “fault” LED, which indicates a

faulty module.

If the removed bezel(s) have air filters,

replace them at this time.

NOTE

: If your system does not contain

a redundant module, place the UPS into

manual bypass mode before removing

modules to prevent accidental loss of

power to the connected equipment.

1. Removing the

module‑securing bracket

Use a Phillips-head screwdriver to

remove the fastener (if installed).

2. Releasing the lock lever

Pull out the lock lever slightly and

lift up, then wait a few seconds

before continuing.

3. Removing the module

from the cabinet bay

Slide the module out about

two-thirds of the way until it is

stopped by the safety catch.

Lift the module slightly and, while

supporting the module, slide it

completely out.

590-1563-501A/SL-55016_REV1_3-17

LIEBERT® APS™ MODULE REPLACEMENT

Quick Installation Guide

BATTERY, POWER, AND

CHARGER MODULE

INSTALLATION

4. Inserting a module

into a cabinet bay

Lift the module to the appropriate

bay, resting the end of the module

on the bay shelf.

NOTE

: Do not rest the module on

any plastic bezels. It could damage

the bezel.

NOTE

: Two battery modules must

be installed in the same row to

complete the battery string.

Slowly push the module in until

about one-third of the module is in

the bay.

Lift the module up, then continue

pushing until about 5 cm (2 in.) of

the module remains outside the bay,

then push it firmly and smoothly to

ensure that it is fully inserted.

5. Engaging the lock lever

Pull out the lock lever slightly

and press the lever down into the

bracket.

NOTE

: If the lever does not press

down smoothly, remove and reinstall

the module.

6. Attaching the

module‑securing bracket

Use a #2 Phillips-head screwdriver

to install the module-securing

bracket.

7. Replace the plastic bezel(s).

590-1563-501A/SL-55016_REV1_3-17

LIEBERT® APS™ MODULE REPLACEMENT

Quick Installation Guide

SYSTEM CONTROL OR

SYSTEM MONITORING

MODULE REMOVAL

CAUTION

When both a control

and monitoring module need replaced,

do not remove them at the same time.

If both are removed, the UPS shuts

down and power is removed from

the connected equipment unless

the system includes an external

maintenance-bypass system, and the

UPS is operating in maintenance-

bypass mode.

1. Remove the display bezel

and the LCD display.

Lay the display module on top

of the UPS.

2. Freeing the module

Use a Phillips-head screwdriver

to remove the screws from the

2 securing holes.

3. Releasing the lock lever

Pull out the lock lever slightly

and pull to the left, then wait a few

seconds before continuing.

4. Removing the module

Being sure to support the module,

slide it completely out of its control

bay.

NOTE

: These modules do not have

a safety catch because they are

lightweight.

SYSTEM CONTROL OR

SYSTEM MONITORING

MODULE INSTALLATION

5. Inserting a module

into a control bay

Push the module in until about 1

cm (1/2 in.) of the module remains

outside the bay, then push it firmly

and smoothly to ensure that it is

fully inserted.

6. Engaging the lock lever

Pull out the lock lever slightly and

press the lever to the right into

the bracket.

7. Re‑attaching the module

to the cabinet

Use a #2 Phillips-head screwdriver

to resecure the module.

8. Replace the LCD display

and the display bezel.

VertivCo.com |Vertiv Headquarters, 1050 Dearborn Drive, Columbus, OH, 43085, USA

registered trademarks of their respective owners. While every precaution has been taken to ensure accuracy and completeness herein, Vertiv Co. assumes no responsibility, and disclaims all

liability, for damages resulting from use of this information or for any errors or omissions. Specications are subject to change without notice.

590-1563-501A/SL-55016_REV1_3-17

Autres manuels Vertiv UPS

Vertiv

Vertiv Liebert EXM Manuel utilisateur

Vertiv

Vertiv Liebert EXM Manuel utilisateur

Vertiv

Vertiv Liebert GXT RT Series Manuel utilisateur

Vertiv

Vertiv Liebert NXL Manuel utilisateur

Vertiv

Vertiv Liebert EXM2 Manuel utilisateur

Vertiv

Vertiv Liebert EXL Manuel utilisateur

Vertiv

Vertiv Liebert GXT RT+ Manuel utilisateur

Vertiv

Vertiv Liebert NXL 500kVA Manuel utilisateur

Vertiv

Vertiv PSA4-1000MT120 Instructions d'installation et d'entretien

Vertiv

Vertiv Liebert NX 225 kVA Manuel utilisateur

Vertiv

Vertiv Liebert EXS Manuel utilisateur

Vertiv

Vertiv Liebert GXT5 Instructions d'installation et d'entretien

Vertiv

Vertiv Liebert GXT5 Instructions d'installation et d'entretien

Vertiv

Vertiv Liebert EXL Manuel utilisateur

Vertiv

Vertiv Liebert ITA2 Manuel utilisateur

Vertiv

Vertiv Liebert APM Plus Manuel utilisateur

Vertiv

Vertiv Liebert PSA5 Manuel utilisateur

Vertiv

Vertiv Liebert EXS Instructions d'installation et d'entretien

Vertiv

Vertiv Liebert EXM TXC Manuel utilisateur

Vertiv

Vertiv Liebert PST4-660MT120 Instructions d'installation et d'entretien

Vertiv

Vertiv Liebert APM Plus Manuel utilisateur

Vertiv

Vertiv Liebert GXT5 Manuel utilisateur

Vertiv

Vertiv Liebert NXC 0060kTJ1AFN02000 Manuel utilisateur

Vertiv

Vertiv Liebert NX Manuel utilisateur

Manuels UPS populaires d'autres marques

Pylontech

Pylontech Victron & Pylontech US5000 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur

Mecer

Mecer ME-1000-WTU Manuel utilisateur

Mustek

Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation

Emerson

Emerson Liebert NXL series Manuel utilisateur

MAKELSAN

MAKELSAN BOXER SERIES Manuel utilisateur

Block

Block PC-0524-400-0 Manuel utilisateur

CyberPower

CyberPower CP585LCD Manuel utilisateur

Eaton

Eaton 3S Instructions de montage

CyberPower

CyberPower Office Tower Series UPS 1000 Manuel utilisateur

CyberPower

CyberPower BM100 Manuel utilisateur

Best Power

Best Power 610 Manuel utilisateur

Best Power

Best Power Unity/I UT3K Manuel utilisateur

Mustek

Mustek PowerMust 400 Offline Manuel utilisateur

Xantrex

Xantrex Trace 512 UR-UPS Manuel utilisateur

Forza

Forza SL-1501UL Manuel utilisateur

LEGRAND

LEGRAND keor 310081 Manuel utilisateur

ABB

ABB Conceptpower DPA 500 Manuel utilisateur