Velleman WC30CT Manuel utilisateur

WC30CT VELLEMAN

WC30CT – DCF Wall Clock

1. Safety

• Do not open the housing and do not expose the device to rain, water, dust, water, extreme temperatures or direct sunlight.

• Only use the device in open air.

• Do not use the device in close proximity to heat sources e.g. radiators.

• Avoid intense vibrations and other mechanical loads.

• Wait 2 hours before activating the device when it is introduced into a new temperature environment (e.g. after transport).

2. Batteries

• Consult a physician immediately if a battery is swallowed.

• Never try to reactivate empty batteries and never open or burn batteries.

• Use only batteries of the same brand and replace all batteries at once.

• The batteries may drain excessively if these instructions are not respected.

• Do not short batteries and do not include them in the domestic waste.

• Dispose of your empty batteries in the legally required fashion. Only throw away completely empty batteries.

• Replace the batteries as follows : open the battery compartment (2), remove the old batteries, insert the new ones and close

the battery compartment. Mind the polarity indications when installing the batteries.

3. General

The WC30CT can be used as a free-standing device and can be hung from the wall. Position the device near a window to

ensure correct reception of the DCF signal. Steel doors and concrete walls can impede signal reception, as can electric

appliances. Do not position the device in close proximity to TV’s, stereos, etc.

This device can either display the time and date through reception of the DCF signal or the user can enter the time and date

manually.

Deploy the two supports (3) to use the WC30CT as a free-standing clock.

Wall mounting : drive a round-headed screw into the wall and let it protrude ± 3 to 4mm. Be careful not to damage any water or

gas pipes. Hang the device from the screw.

4. Setting the Correct Date and Time

Using the DCF Signal

The device will tryto receive theDCF signal as soon as thebatteries areinstalled orthe WAVE button is pressed. It may take the

device up to 7 minutes to locatethe signal. Note that the buttons at the back of the device will not work during this time. As soonas

reception of the DCF signal is clear, the message “WAVE OK” and the symbol are displayed (the symbol nolonger

flashes).

The user doesn’t need to set the clock, the calendar or the day of the week.

WC30CT VELLEMAN

Manual Time Setting

Hold the MODE button for 3 seconds to make the digits for the year, month, date and day of the week flash. Set the year, month &

datewith the YEAR, MONTH & DATE buttons. The day of the week changes automatically when the date is adjusted.

Remember that the digits change fasterwhen a button is held.

Press MODE to make the digits for the clock flash. Set the hours, minutes and seconds with the HOUR, MIN & SEC buttons

respectively.

Press MODE again to make the digits for the display language flash. Select the display language with the COUNTRY button :

English, Dutch, French or German (EN

ENEN

EN, DU

DUDU

DU, FR

FRFR

FR or GE

GEGE

GE).

Important Remark : the manual time setting will be overridden if a DCF signal is received.

5. Selecting the Displayed Data

Select the displayed data with the MODE button at the back of the device. Press it to toggle between alarm time display and

normal clock display.

6. Setting the Alarm Time

Press MODE inthe normal display mode to display the current alarm time. Enter the hours and minutes with the HOUR and MIN

buttons. Press the ALM button repeatedly to select the alarm mode :

• symbol is displayed: the alarm will go off for oneminute once every24 hours. Press anarbitrary button to stopthe alarm.

• and are displayed : press an arbitrary button to stop the alarm temporarily. The alarm is reactivated some time later.

Press MODE againtoreturnto thenormal displaymode.

7. Temperature Readout

Press the °C/°F-button to select a temperature readout in °C or °F when the device is in the normal display mode.

8. Selecting 12hr- or 24hr-mode

Press the "12/24"-button when the device is in the normal display mode to display the time either in 12hr- or 24hr-mode.

9. Reset Button

Press the small yellow button at the back with a sharp object to reset the device.

10. Maintenance and Safety Instructions

Use a soft cloth moistened with mild detergent to clean the device. Do not use abrasives or solvents on the device. Do not drop the

device on a hard surface. Do not use it outdoors and shield it from direct sunlight.

11. Replacing Batteries

Insert two newAA-batterieswhen the screen becomes illegible.

12. Maintenance

Wipe the device with a clean cloth and some mild detergent.

13. Warranty

The warranty conditions are mentioned on the included warranty card.

Autres manuels Velleman Horloge

Velleman

Velleman WT8732 Manuel utilisateur

Velleman

Velleman WC1857 Manuel utilisateur

Velleman

Velleman WC30D4 Manuel utilisateur

Velleman

Velleman WT33 Manuel utilisateur

Velleman

Velleman K8009 Manuel utilisateur

Velleman

Velleman wc4171 Manuel utilisateur

Velleman

Velleman WC103 Manuel utilisateur

Velleman

Velleman WCM2 Manuel utilisateur

Velleman

Velleman WT82 Manuel utilisateur

Velleman

Velleman Perel WC118 Manuel utilisateur

Velleman

Velleman WC25 Manuel utilisateur

Velleman

Velleman WC3320 Manuel utilisateur

Velleman

Velleman WT11EL Manuel utilisateur

Velleman

Velleman WC35 Manuel utilisateur

Velleman

Velleman WC120 Manuel utilisateur

Velleman

Velleman ED8A800 Manuel utilisateur

Velleman

Velleman WT302N Manuel utilisateur

Velleman

Velleman WT8097 Manuel utilisateur

Velleman

Velleman WST8089 Manuel utilisateur

Velleman

Velleman WT302 Manuel utilisateur

Velleman

Velleman WC25G Manuel utilisateur

Velleman

Velleman WC235RL Manuel utilisateur

Velleman

Velleman ED8A101 Manuel utilisateur

Velleman

Velleman WC8708 Manuel utilisateur

Manuels Horloge populaires d'autres marques

Silicon Laboratories

Silicon Laboratories SI5324 Manuel utilisateur

Heathkit

Heathkit GC-1005 Manuel utilisateur

Oregon Scientific

Oregon Scientific PRYSMA RMR221P Manuel utilisateur

Andrew O'Malley

Andrew O'Malley DOTKLOK Manuel utilisateur

ALGE-Timing

ALGE-Timing ASC3 Manuel utilisateur

Bodet

Bodet Profil 960 Manuel utilisateur

Nixie Clock

Nixie Clock Divergence Meter Manuel utilisateur

La Crosse Technology

La Crosse Technology WS-8256-AL Manuel utilisateur

Mini Gadgets

Mini Gadgets MCPro Manuel utilisateur

Casio

Casio TMR-200 Manuel utilisateur

Progetti

Progetti ILTEMPOSTRINGE Manuel

BVItech

BVItech BV-101 Manuel utilisateur

Progetti

Progetti KALIMERO Manuel

La Crosse Technology

La Crosse Technology WT-3141b Manuel

La Crosse Technology

La Crosse Technology W86531 Manuel utilisateur

Sharp

Sharp SPC900 Manuel utilisateur

La Crosse Technology

La Crosse Technology 404-50447 Manuel utilisateur

Datexx

Datexx DF0063 Manuel utilisateur