Vaporesso TARGET 100 Manuel utilisateur
User Manual
Thank you for choosing Vaporesso product. Please read this instruction carefully before use to ensure a perfect
experience. If there is any additional requirement about this product, please consult the local agent or contact us
through our website: www.vaporesso.com
Drip Tip
Power Button
0.96" TFT Screen
“+” Button
Mode/ Conrm Button
“-” Button
Type-C USB Port
Glass Tube
Top Cap
Air-inlet Port
EXPLODED VIEW
SPECIFICATIONS
Dimensions: 140.3*28.6*35.1mm
POD Capacity: 5ml/2ml(TPD)
Coils & Suggested Wattage:
GTi 0.2Ω MESH Coil (60-75W)
GTi 0.4Ω MESH Coil (50-60W)
Battery Capacity: 1 x 18650/21700 Battery(Not Included)
Output Power: 5-100W
Charging Current: DC 5V/2A,Type-C
Battery Display : 0.96’’ TFT Screen
PACKING LIST
1 x VAPORESSO TARGET 100 MOD
1 x VAPORESSO iTANK (5ml/2ml TPD)
1 x GTi 0.2Ω MESH Coil (Pre-installed)
1 x GTi 0.4Ω MESH Coil (In-BOX)
1 x Extra Glass Tube
3 x O-ring
1 x Type-C Cable
1 x User Manual
1 x Warranty Card
FIGURES
Figure 1: Replace the coil Figure 3 User Interface
OPEN CLOSE
Figure 2: Fill e-liquid
Wattage
Output Voltage
Battery Level
Vaping Time
System Lock
Output Mode
Pu Counter
Resistance
Smart VW
1
English
ENGLISH
USE INSTRUCTIONS
1. Install the Tank
Install the tank to the battery by screwing the 510 thread. Make sure they are rmly connected.
2. Replace the Coil
- Unscrew the thread base from the tank;
- Pull out the used coil from the tank;
- Install a new coil to the tank;
- Reattach the thread base into place.
* Refer to the gure 1.
3. Fill E-liquid
- Push the top cap according to the arrow direction;
- ll e-liquid through the hole, then lock the top cap in place after lling is nished.
- Please wait 5 minutes for the e-liquid to soak into the coil completely.
* Refer to the gure 2.
4. Adjust the Airow
To adjust the airow volume, please rotate the air-inlet ring on the bottom of the tank.
5. Power On/O the Device
Power on/o: press the power button 5 times in 2s.
6. Power Adjustment
TARGET 100 Kit is using the powerful GTi coil platform, and the suggested power need to be noticed
before start vaping.
GTi MESH Coils GTi 0.2 MESH GTi 0.4 MESH
Suggested Power 60-75W 50-60W
7. Start Vaping
Press the power button to enjoy extraordinary vaping experience.
2English
8. Charge the Battery
After connecting the Type-C cable to the battery, the battery indicator and remaining charging time will be showed on
the screen.
9.Lock or unlock the device
Press the re button 3 times, then the +, - and mode buttons will be locked. In the same way, the buttons will be
unlocked and the screen will be unlocked.
10. Choose a Mode
1. Long press the mode button for main mode selection ( Pulse Mode/F(t) Mode/VWN Mode).
2. Press the mode button 3 times continuously for secondary menu setting.
*F(t): F(t) MODE (DEFAULT)
F(t) MODE is by adjusting temperature, heating speed and time, F(t) mode releases the avors of e-liquid adequately,
delivering the perfect balanced tasting experience consistently from the rst pu throughout.
*PUL: PULSE MODE
PULSE MODE is a mode to improve vaping experience through constant voltage output, delivering optimal flavor
production, throat hit, nicotine satisfaction, and perfect temperature cloud continuously.
*VWN: VARIABLE WATTAGE MODE/ SIMPLE MODE
VWN MODE is a normal mode of output wattage, you can according to the coil resistance to adjust the best wattage for
your needs. The user interface shows wattage, resistance and pu counter for your immersive vaping experience.
*DIY: DIY MODE
You can choose traditional VW (H, N, S), VV, BP (Bypass) modes in this section.
*SET: SYSTEM SET
System setting includes DEFAULT, SMART VW, PUFF, and VERSION options.
SMART VW: when this function is turned on and a TANK is installed, the system will recommend the best power.
3
English
1. Short circuit protection & Low resistance protection:
When the load resistance is less than 0.1±0.01Ω, press power button could trigger the short circuit protection or Low
resistance protection, the device will close the output, at the same time OLED display will show “SHORT ATOMIZER”.
2. No load protection:
When no load resistance is detected, press power button could trigger the no load protection, the device will close the
output, at the same time OLED display will show “CHECK ATOMIZER”.
3. High resistance protection:
When the load resistance is greater than 5±0.5Ω, press power button could trigger the high resistance protection, the
device will close the output, at the same time OLED display will show “ CHECK ATOMIZER ”.
4. Low voltage protection:
When the voltage of the battery cell is lower than 3.3±0.1V, press power button could trigger the low voltage protection,
the device will close the output, at the same time OLED display will show “LOW BATTERY”.
5. PCBA(Printed Circuit Board Assembly):
When the temperature of the PCBA(Printed Circuit Board Assembly) temperature sensor is higher than 70+5℃/-10℃,
press power button could trigger the PCBA (Printed Circuit Board Assembly) over heat protection, the device will close
the output, at the same time OLED display will show “OVER HEAT”.
6. Over discharge protection:
During the process of smoking, when the battery cell voltage is lower than 2.9±0.1 V, the device will close the
output automatically.
7. Over charge protection:
During charging, when the battery cell voltage is greater than 4.1±0.1V, OLED display will show “100%”. At the end of
charging, battery cell voltage will not exceed 4.2±0.03V.
8. Auto-shut o protection:
When POWER button is held for 10±1 seconds, the device will close the output, at the same time OLED display will show
“OVER TIME”.
9. Battery cell anti-reverse connection protection:
The inversion of battery cell will not damage the battery.
PROTECTIONS
4English
1. Please turn o the device when it is not in use.
2. Do not leave the charging device unattended.
3. Do not drop, throw or abuse your device, which may cause damage.
4. Please use a standard USB output charger with proper charging current and voltage range.
5. Keep away from the water or any ammable gas, liquid .
6. Do not expose the device to direct sunlight, dust, moisture or mechanical shock.
7. Do not expose the device to extreme temperature. (Recommended temperature range: -10~60℃ /14~140℉while using
and -10~45℃ /14~113℉while storing).
8. EEE Recycling: the product should not be treated as household waste, instead, it should be handed over to the
applicable collection point for the recycling of electrical and electronic equipment.
9. Battery Recycling: the product battery should not be treated as household waste, instead, it should be handed over
to the applicable used battery collection point for recycling.
10. Only have your device repaired by Vaporesso. Do not attempt to repair it by yourself as damage or personal injury
may occur.
WARNINGS
This rellable electronic cigarette is intended for use with compatible e-liquid, which may contain nicotine. Nicotine is
an addictive substance and it is not suitable or recommended to use in following cases:
1. This device is not suitable for:
- Persons under the legal smoking age.
- Persons experiencing heart disease, stomach or duodenal ulcers, liver or kidney problems, long-term throat disease or
dicult breathing due to bronchitis, emphysema or asthma.
- Persons with an overactive thyroid gland or experiencing phaeochromocytoma (a tumour of the adrenal gland that can
aect blood pressure).
- Persons taking certain medications like Theophylline, Ropinirole or Clozapine and etc..
CAUTIONS
5
English
2. This device is not recommended for:
- Non-smokers
- Pregnant or breastfeeding women
3. You may experience the following results if you use nicotine containing e-liquid with this product. If it happens,
please consult a healthcare professional and show them this leaet if possible:
- Feeling faint - Nausea - Dizziness - Headache - Coughing - Irritation of the mouth or throat
- Stomach discomfort - Hiccups - Nasal congestion - Vomition
- Chest palpitations/pain or an irregular heart rate
This device should not be used by persons under the legal smoking age.
Table des matières
Autres manuels Vaporesso cigarette électronique
Vaporesso
Vaporesso GTX ONE Manuel utilisateur
Vaporesso
Vaporesso Zero 2 Manuel utilisateur
Vaporesso
Vaporesso Revenger Manuel utilisateur
Vaporesso
Vaporesso Revenger X Manuel utilisateur
Vaporesso
Vaporesso TARGET PM30 Manuel utilisateur
Vaporesso
Vaporesso XROS 3 Manuel utilisateur
Vaporesso
Vaporesso XROS Nano FGSB7 Manuel utilisateur
Vaporesso
Vaporesso Target Mini Manuel utilisateur
Vaporesso
Vaporesso XIRON Manuel utilisateur
Vaporesso
Vaporesso LUXE X Manuel utilisateur
Vaporesso
Vaporesso LUXE Q2 SE Manuel utilisateur
Vaporesso
Vaporesso orca SOLO Manuel utilisateur
Vaporesso
Vaporesso LUXE XR MAX Manuel utilisateur
Vaporesso
Vaporesso COSS Manuel utilisateur
Vaporesso
Vaporesso LUXE XR MAX Manuel utilisateur
Vaporesso
Vaporesso VAPORESSO XROS Manuel utilisateur
Vaporesso
Vaporesso GEN 200 Manuel utilisateur
Vaporesso
Vaporesso LUXE S Manuel utilisateur
Vaporesso
Vaporesso Target MINI II Kit Manuel utilisateur
Vaporesso
Vaporesso Polar Manuel utilisateur
Manuels cigarette électronique populaires d'autres marques
STEAMAX
STEAMAX TFV8 X-BABY Manuel utilisateur
iQOS
iQOS 3 MULTI Manuel utilisateur
ZAZO
ZAZO PRO Mini 2 Manuel utilisateur
Aquafog
Aquafog Turbo XE Manuel
Electronic Cigarettes Australia Pty Ltd
Electronic Cigarettes Australia Pty Ltd AUSSIE BLUE ENDURANCE Manuel utilisateur
UWELL
UWELL Whirl T1 Manuel utilisateur
