TSI Instruments 3075 Manuel utilisateur

Model 3075/3076

Constant Output Atomizer

Instruction Manual

P/N 1933076, Revision H

October 2002

Particle Instruments

Product Overview 1

Model 3075/3076

Constant Out

Unpacking the

Atomizer

Atomizer Setting Up the

Atomizer

Instruction Manual Operating the

Atomizer

Applications

Atomizer

Maintenance and

Service

Appendixes

Manual History

The following is a manual history of the Model 3075/3076 Constant

Output Atomizer Instruction Manual (Part Number 1933076).

Revision Date

First Version

B March 1989

C June 1993

D January 1994

E September 1994

F May 1996

August 1998

G July 2000

H October 2002

Revision C of this manual reformats the manual, modifies the setup

instructions, and adds the Safety section.

In revision D, TSI’s customer service number was changed.

In revision E, revisions were made throughout the manual.

In revision F, TSI’s “Limitation of Warranty and Liability” on page iii

was updated.

In August 1998, TSI’s area code was changed from 612 to 651.

In revision G, TSI’s Limitation of Warranty and Liability was

updated.

In revision H, TSI’s phone numbers and address were updated.

iii

Part Number 1933076 / Revision H / October 2002

Address TSI Incorporated / 500 Cardigan Road / St. Paul, MN 55126 / USA

Fax No. (651) 490-3824

E-mail Address [email protected]

Limitation of Warranty

and Liability

(effective July 2000)

Seller warrants the goods sold hereunder, under normal use and service as

described in the operator's manual, shall be free from defects in workmanship and

material for (12) months, or the length of time specified in the operator's manual,

from the date of shipment to the customer. This warranty period is inclusive of any

statutory warranty. This limited warranty is subject to the following exclusions:

a. Hot-wire or hot-film sensors used with research anemometers, and certain other

components when indicated in specifications, are warranted for 90 days from

the date of shipment.

b. Parts repaired or replaced as a result of repair services are warranted to be free

from defects in workmanship and material, under normal use, for 90 days from

the date of shipment.

c. Seller does not provide any warranty on finished goods manufactured by others

or on any fuses, batteries or other consumable materials. Only the original

manufacturer's warranty applies.

d. Unless specifically authorized in a separate writing by Seller, Seller makes no

warranty with respect to, and shall have no liability in connection with, goods

which are incorporated into other products or equipment, or which are modified

by any person other than Seller.

The foregoing is IN LIEU OF all other warranties and is subject to the LIMITATIONS

stated herein. NO OTHER EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR

PARTICULAR PURPOSE OR MERCHANTABILITY IS MADE.

TO THE EXTENT PERMITTED BY LAW, THE EXCLUSIVE REMEDY OF THE USER

OR BUYER, AND THE LIMIT OF SELLER'S LIABILITY FOR ANY AND ALL LOSSES,

INJURIES, OR DAMAGES CONCERNING THE GOODS (INCLUDING CLAIMS BASED

ON CONTRACT, NEGLIGENCE, TORT, STRICT LIABILITY OR OTHERWISE) SHALL

BE THE RETURN OF GOODS TO SELLER AND THE REFUND OF THE PURCHASE

PRICE, OR, AT THE OPTION OF SELLER, THE REPAIR OR REPLACEMENT OF THE

GOODS. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY SPECIAL,

CONSEQUENTIAL OR INCIDENTAL DAMAGES. SELLER SHALL NOT BE

RESPONSIBLE FOR INSTALLATION, DISMANTLING OR REINSTALLATION COSTS

OR CHARGES. No Action, regardless of form, may be brought against Seller more

than 12 months after a cause of action has accrued. The goods returned under

warranty to Seller's factory shall be at Buyer's risk of loss, and will be returned, if at

all, at Seller's risk of loss.

Service Policy Knowing that inoperative or defective instruments are as detrimental to TSI as they

are to our customers, our service policy is designed to give prompt attention to any

problems. If any malfunction is discovered, please contact your nearest sales office

or representative, or call TSI’s Customer Service department at 1-800-874-2811

(USA) or (651) 490-2811.

iv Model 3075/3076 Constant Output Atomizer

Safety

This section gives instructions to promote safe and proper handling

of the Model 3075/3076 Constant Output Atomizer.

The Model 3075/3076 Constant Output Atomizer is designed to

release aerosol to a system that is at atmospheric pressure.

Therefore, the pressure at the outlet of the Atomizer should be

maintained close to atmospheric pressure (below 10 psig).

The atomizer is equipped with a pressure relief valve that actuates

whenever the pressure in the bottle exceeds 10 psig. The valve will

reseal when pressure in the bottle is reduced below 10 psig.

However:

 Do not operate the Atomizer with an outlet pressure exceeding

10 psig in a closed system. Operating the Atomizer above this

pressure may result in damage to the plastic-coated glass

bottle, which can shatter and cause serious personal injury.

 Experiments have shown the plastic-coated glass bottle may

explode at pressures exceeding 80 psig. Before applying

compressed air to the Atomizer, check your system to ensure no

blockage of the Atomizer can occur at the Atomizer outlet.

 The plastic-coated glass bottle may weaken or develop cracks

from shock, excessive use, or chemical attack, resulting in

fractures at pressures well below 80 psig. Before attaching the

bottle to your system, check the bottle to ensure there is no

structural weakness. If you suspect your bottle is damaged,

contact TSI Incorporated for replacement information.

Note: Refer to Chapter 6 of this manual for instructions on

contacting technical personnel at TSI.

WARNING

Do not operate the Atomizer with an outlet pressure exceeding 10 psig in a

closed system. Operating the Atomizer with an outlet pressure greater than

10 psig may result in damage to the plastic-coated glass bottle, which can shatter

and cause serious personal injury. The atomizer is equipped with a pressure

relief safety valve that releases pressures above 10 psig from within the bottle.

Never block the outlet of this valve or remove the valve from the bottle cap.

vi Model 3075/3076 Constant Output Atomizer

Contents

vii

Manual History .......................................................................... ii

Safety ..........................................................................................v

About This Manual.....................................................................xi

Purpose................................................................................. xi

Organization ......................................................................... xi

Related Product Literature ................................................... xii

Reusing and Recycling ......................................................... xii

Getting Help.........................................................................xiii

Submitting Comments .........................................................xiv

Chapters

1 Product Overview ............................................................. 1-1

Introduction ........................................................................ 1-1

How the Atomizer Works ..................................................... 1-2

2 Unpacking the Atomizer .................................................. 2-1

Unpacking List.................................................................... 2-1

Unpacking Instructions....................................................... 2-2

3 Setting Up the Atomizer .................................................. 3-1

Meeting Clean Air Requirements ......................................... 3-1

Selecting and Preparing the Solution................................... 3-2

Setting Up the Model 3076 Atomizer ................................... 3-2

Before You Begin ........................................................... 3-2

Setting Up in the Recirculation Mode............................. 3-2

Modifying the Model 3076 for use in Nonrecirculation

Mode .......................................................................... 3-4

Setting Up the Model 3075 Atomizer ................................... 3-5

Before You Begin ........................................................... 3-5

Setting Up in the Nonrecirculation Mode ....................... 3-6

Modifying the Model 3075 for use in the Recirculation

Mode .......................................................................... 3-8

4 Operating the Atomizer ................................................... 4-1

Operating in the Recirculating Mode ................................... 4-1

Operating in the Nonrecirculating Mode .............................. 4-2

Drying the Aerosol............................................................... 4-3

Neutralizing the Aerosol ...................................................... 4-4

viii Model 3075/3076 Constant Output Atomizer

5 Atomizer Applications ..................................................... 5-1

Generating Solid Particles ................................................... 5-1

Generating Oil Aerosol ........................................................ 5-6

Dispersing Polystyrene Latex Particles ................................ 5-6

Dispersing Solid Particles.................................................... 5-6

6 Atomizer Maintenance and Service ................................. 6-1

Maintaining the Atomizer .................................................... 6-1

Servicing the Atomizer......................................................... 6-3

Technical Contacts ........................................................ 6-3

Returning the Atomizer for Service ................................ 6-3

Appendixes

A Specifications .................................................................... A-1

B Technical Paper .................................................................B-1

C Bibliography........................................................................C-1

Figures

1-1 Model 3076 Constant Output Atomizer.............................. 1-1

1-2 Model 3075/3076 Schematic............................................. 1-3

3-1 Model 3076 Atomizer in the Recirculation Mode ................ 3-3

3-2 Model 3076 Atomizer Modified for the

Nonrecirculation Mode..................................................... 3-5

3-3 Model 3075 Atomizer in the Nonrecirculation Mode ........... 3-7

4-1 Model 3062 Diffusion Dryer .............................................. 4-4

5-1 Particle Diameter Mean, Mode and Standard Deviation vs.

Salt Concentration .......................................................... 5-1

5-2 Size Distribution of Sodium Chloride Aerosols Generated

by the Atomizer ............................................................... 5-2

5-3 Typical Number Distribution of a Sodium Chloride

Aerosol Atomized from 0.001 gram/cm3Solution ............ 5-3

5-4 Typical Surface Area Distribution of a Sodium Chloride

Aerosol Atomized from 0.001 gram/cm3Solution ............ 5-4

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels TSI Instruments cigarette électronique

TSI Instruments

TSI Instruments 3076 Manuel utilisateur

Manuels cigarette électronique populaires d'autres marques

STEAMAX

STEAMAX TFV8 X-BABY Manuel utilisateur

iQOS

iQOS 3 MULTI Manuel utilisateur

Vaporesso

Vaporesso LUXE XR MAX Manuel utilisateur

ZAZO

ZAZO PRO Mini 2 Manuel utilisateur

Aquafog

Aquafog Turbo XE Manuel

Electronic Cigarettes Australia Pty Ltd

Electronic Cigarettes Australia Pty Ltd AUSSIE BLUE ENDURANCE Manuel utilisateur

UWELL

UWELL Whirl T1 Manuel utilisateur

VooPoo

VooPoo VMATE Manuel utilisateur

Yogs-Pfeifen

Yogs-Pfeifen E-PIPE nex KLASSIK Manuel utilisateur

Vaporesso

Vaporesso GTX ONE Manuel utilisateur

VooPoo

VooPoo DRAG 2 Manuel utilisateur

Innova

Innova 3.0 Manuel utilisateur

Aquafog

Aquafog XE CRSM Manuel utilisateur

hi-Fun

hi-Fun hi-Cigarette Manuel utilisateur

Neptronic

Neptronic SKH Series Manuel utilisateur

Vaporesso

Vaporesso LUXE Q2 SE Manuel utilisateur

iQOS

iQOS 3 DUO Manuel utilisateur

STEAMAX

STEAMAX REULEAUX RX300 Manuel utilisateur