Unitronics V230 Manuel utilisateur

Headquarters

Unitronics (1989) (R"G) Ltd.

Unitronics Building, Airport City

P.O.B. 300, Ben Gurion Airport, Israel 70100

Tel: + 972 (3) 977 8888 Fax: + 972 (3) 977 8877

Unitronics

Replacing a Battery: V230/260/280/290

Tech Support Document 4/06

Before you can replace a battery in a controller comprising a Snap-in I/O module, you must

remove it before you can open the controller. Note that replacement batteries, 3V CR2450; may

be ordered from Unitronics.

Note that in order to avoid losing data, you replace the battery when the controller is running.

The instructions below feature the V230 for representational purposes, and are relevant for the

following Vision models: V230/260/280/290.

Removing a Snap-in I/O Module

xTurn off the power before removing or installing I/O modules.

1. Locate the four buttons on the sides of the controller, two on either side.

2. Press the buttons and hold them down to open the locking mechanism.

3. Gently rock the module from side to side, easing the module from the controller.

www.klinkmann.com

Replacing a Battery: V230/260/280/290 Tech Support Document 4/06

2 Unitronics

Replacing the Battery

xBefore opening the controller, touch a grounded object to discharge any electrostatic

charge.

xAvoid directly touching PCB boards.

To preserve data, replace the battery when the controller is running. If you have

disconnected the power to remove a Snap-in I/O module, reconnect the power supply cable

and power-up the controller before opening it.

Removing the rear panel of controller:

1. Locate the 4 slots on the sides of the

controller.

2 Open the controller by inserting a

stylus or a flat-bladed screwdriver

into the slots located on the side of

the controller, then carefully prying

off the rear panel.

www.klinkmann.com

5 / 2011

4/06 Replacing a Battery: V230/260/280/290 Tech Support Document

Unitronics 3

3. Remove the battery by holding it as shown

in the accompanying figure, and gently

sliding it out from under the clip.

4. Slide the new battery sideways under the

clip as shown. The clip must hold the

battery securely.

Note that the side of the battery bearing

text (+) must face up.

5. Close the controller by snapping the

plastic cover back in its place.

www.klinkmann.com

5 / 2011

Replacing a Battery: V230/260/280/290 Tech Support Document 4/06

Re-installing a Snap-in I/O Module

1. Line the circular guidelines on the controller up with the guidelines on the Snap-in I/O Module as

shown below.

2 Apply even pressure on all 4 corners until you hear a distinct ‘click’. The module is now installed.

Check that all sides and corners are correctly aligned.

The information in this document reflects products at the date of printing. Unitronics reserves the right, subject to all applicable laws, at any time, at its sole discretion, and without

notice, to discontinue or change the features, designs, materials and other specifications of its products, and to either permanently or temporarily withdraw any of the forgoing from the

market.

All information in this document is provided "as is" without warranty of any kind, either expressed or implied, including but not limited to any implied warranties of merchantability,

fitness for a particular purpose, or non-infringement. Unitronics assumes no responsibility for errors or omissions in the information presented in this document. In no event shall

Unitronics be liable for any special, incidental, indirect or consequential damages of any kind, or any damages whatsoever arising out of or in connection with the use or performance

of this information.

The tradenames, trademarks, logos and service marks presented in this document, including their design, are the property of Unitronics (1989) (R"G) Ltd. or other third parties and you

are not permitted to use them without the prior written consent of Unitronics or such third party as may own them

Unitronics_Manuals_V2xxx_Instal_Battery_en_0511.pdf

Samara

tel. +7 846 273 95 85

[email protected]

Yekaterinburg

tel. +7 343 376 5393

yekat[email protected]

St. Petersburg

tel. +7 812 327 3752

[email protected]

Moscow

tel. +7 495 641 1616

[email protected]

Helsinki

tel. +358 9 540 4940

automation@klinkmann.ﬁ

Vilnius

tel. +370 5 215 1646

[email protected]

Riga

tel. +371 6738 1617

[email protected]

Мinsk

tel. +375 17 200 0876

[email protected]

Tallinn

tel. +372 668 4500

[email protected]

Кiev

tel. +38 044 495 33 40

[email protected].ua

www.klinkmann.com

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Unitronics Contrôleurs

Unitronics

Unitronics Vision V350-35-T2 Manuel utilisateur

Unitronics

Unitronics V120-22-R34 Manuel utilisateur

Unitronics

Unitronics Vision 230 Manuel utilisateur

Unitronics

Unitronics UniStream USC-B3-R20 Manuel utilisateur

Unitronics

Unitronics Vision120 Manuel utilisateur

Unitronics

Unitronics M91-19-R1 Manuel utilisateur

Unitronics

Unitronics Samba OPLC Series Manuel utilisateur

Unitronics

Unitronics Vision OPLC V570-57-C30B Manuel utilisateur

Unitronics

Unitronics Vision V130-T2 Manuel utilisateur

Unitronics

Unitronics Vision OPLC V130-J-B1 Manuel utilisateur

Unitronics

Unitronics Jazz JZ20-J-UN20 Manuel utilisateur

Unitronics

Unitronics UniStream Built-in Series Manuel utilisateur

Unitronics

Unitronics Samba OPLC SM43-J-R20 Manuel utilisateur

Unitronics

Unitronics UniStream USC-B5-B1 Manuel utilisateur

Unitronics

Unitronics V130-33-TR6 Manuel utilisateur

Unitronics

Unitronics Vision OPLC V560-T25B Manuel utilisateur

Unitronics

Unitronics VisionV120-22-UN2 Manuel utilisateur

Unitronics

Unitronics Samba OPLC SM43-J-R20 Manuel utilisateur

Unitronics

Unitronics MJ20-MEM1 Manuel utilisateur

Unitronics

Unitronics Vision V130-33-R34 Manuel utilisateur

Unitronics

Unitronics Vision OPLC V130 Manuel utilisateur

Unitronics

Unitronics Vision OPLC V1040-T20B Manuel utilisateur

Unitronics

Unitronics Vision OPLC V350-35-TR20 Manuel utilisateur

Unitronics

Unitronics Vision OPLC V1040-T20B Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur