Ultimaker 2 Extended Manuel utilisateur

Manual for the Ultimaker 2+

and Ultimaker Extended 2+

3D printers

Makers Lab

Ver. 01NL okt19

MAKERS LAB

Benno Premselahuis

Rhijnspoorplein 1

1091

GC Amsterdam

Contents

Begin 3D printing ..........................................................................................................3

Removing and introducing material...............................................................................4

Introducing material ......................................................................................................9

Preparing build plate...................................................................................................12

Preparing 3D print in Cura 4.2.1 .................................................................................13

Begin printing..............................................................................................................17

3D print ready .............................................................................................................18

Ver. 01NL okt19

MAKERS LAB

Benno Premselahuis

Rhijnspoorplein 1

1091

GC Amsterdam

Begin 3D printing

The manual is based on Cura version 4.2.1.

There is already material

in the printer and I will be

printing with this material.

Continue on page 12.

There is no material in the

printer. Continue on

page 9.

There is already material

in the printer, but I will not

be printing with this

material. Continue on

page 4.

There is already material

in the printer and I want to

remove it. Continue on

page 4.

Ver. 01NL okt19

MAKERS LAB

Benno Premselahuis

Rhijnspoorplein 1

1091

GC Amsterdam

Removing and introducing material

Switch on the printer with the switch

on the back to the left.

Twist the knob on front and select

MATERIAL.

Press the button.

Select CHANGE and press the

button.

The printing head will be heated up

to prepare for removing the

material.

The material will then be retracted

through the Bowden tube.

Ver. 01NL okt19

MAKERS LAB

Benno Premselahuis

Rhijnspoorplein 1

1091

GC Amsterdam

Remove the material from the

feeder.

Be certain that you also remove the

thin strands of residual material

from the Bowden tube which are

attached to the material.

Press the spool holder inside and

remove the spool from the spool

holder.

Do you only want to remove the

material?

In that case, switch off the printer

with the switch on the back to the

left.

Ver. 01NL okt19

MAKERS LAB

Benno Premselahuis

Rhijnspoorplein 1

1091

GC Amsterdam

Place another spool on the spool

holder. The material should run off

the spool on the bottom, on the

feeder side.

Snip off the end, making a level cut.

Select READY and press the

button.

Select PLA and press the button.

Ver. 01NL okt19

MAKERS LAB

Benno Premselahuis

Rhijnspoorplein 1

1091

GC Amsterdam

The printer head will heat up.

Wait until the menu ‘Insert new

material from the…..’ appears.

Now insert material into the bottom

of the feeder until the feeder grasps

the material. If necessary, you can

press up the switch on the side.

Select READY and press the

button.

The material will be led through the

Bowden tube.

Ver. 01NL okt19

MAKERS LAB

Benno Premselahuis

Rhijnspoorplein 1

1091

GC Amsterdam

Wait until the material leaving the

nozzle is the same colour as the

material that was introduced.

Select READY and press the

button.

Select ‘Return’ and press it twice.

You have now returned to the Start

menu.

Ver. 01NL okt19

MAKERS LAB

Benno Premselahuis

Rhijnspoorplein 1

1091

GC Amsterdam

Introducing material

Switch on the printer with the switch

on the back to the left.

Place a spool on the spool holder.

The material should run off the

spool on the bottom, on the feeder

side.

Snip off the end, making a level cut.

Select MAINTENANCE and press

the button.

Select ADVANCED and press the

button.

Select ‘Insert material’ and press

the button.

Ver. 01NL okt19

MAKERS LAB

Benno Premselahuis

Rhijnspoorplein 1

1091

GC Amsterdam

The printer head will heat up.

Wait until the menu ‘Insert new

material from the…..’ appears.

Now insert material into the bottom

of the feeder until the feeder grasps

the material. If necessary, you can

press up the switch on the side.

Select READY and press the

button.

The material will be led through the

Bowden tube.

Autres manuels pour 2 Extended

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Ultimaker Imprimante 3D

Ultimaker

Ultimaker 3 Extended Guide de configuration

Ultimaker

Ultimaker UM2 Manuel utilisateur

Ultimaker

Ultimaker 2 Go Manuel utilisateur

Ultimaker

Ultimaker S5 Material Station Manuel utilisateur

Ultimaker

Ultimaker S3 Guide d'installation

Ultimaker

Ultimaker 2 Extended Manuel utilisateur

Ultimaker

Ultimaker 2 Extended Manuel utilisateur

Ultimaker

Ultimaker PVA Removal Station Manuel utilisateur

Ultimaker

Ultimaker S5 Material Station Manuel utilisateur

Ultimaker

Ultimaker 3 Extended Guide de configuration

Ultimaker

Ultimaker 2 Extended Manuel utilisateur

Ultimaker

Ultimaker S5 Material Station Manuel utilisateur

Ultimaker

Ultimaker 2 Extended Manuel utilisateur

Ultimaker

Ultimaker 3 Extended Manuel utilisateur

Ultimaker

Ultimaker 2 Extended Manuel utilisateur

Ultimaker

Ultimaker S5 Material Station Manuel utilisateur

Ultimaker

Ultimaker 2 Extended Manuel utilisateur

Ultimaker

Ultimaker 2 Extended Manuel utilisateur

Ultimaker

Ultimaker ORIGINAL+ Manuel utilisateur

Ultimaker

Ultimaker 2 Extended Manuel d'utilisation et d'entretien

Ultimaker

Ultimaker S3 Manuel utilisateur

Ultimaker

Ultimaker ORIGINAL+ Manuel utilisateur

Ultimaker

Ultimaker 3 Extended Manuel utilisateur

Ultimaker

Ultimaker Heated Bed Upgrade Kit Manuel utilisateur

Manuels Imprimante 3D populaires d'autres marques

EcubMaker

EcubMaker TOYDIY Manuel utilisateur

AnyCubic

AnyCubic Kossel Plus Manuel utilisateur

ReDeTec

ReDeTec ProtoCycler Manuel utilisateur

Kywoo3D

Kywoo3D Tycoon IDEX Manuel utilisateur

CraftBot

CraftBot PLUS PRO Manuel utilisateur

3DGence

3DGence INDUSTRY F340 Manuel utilisateur

HP Jet Fusion 4200 Mode d'emploi

Rokit

Rokit AEP Series Manuel utilisateur

AnkerMake

AnkerMake M5 Manuel utilisateur

DIYElectronics

DIYElectronics PRUSA I3 Instructions de montage

Ackuretta

Ackuretta FreeShape 120 Manuel utilisateur

LONGER

LONGER LK5Pro Manuel utilisateur

Stratasys

Stratasys J850 Manuel utilisateur

MakerBot

MakerBot Replicator Manuel utilisateur

Stratasys

Stratasys FDM Vantage Series Manuel utilisateur

ZYYX

ZYYX Pro II Manuel utilisateur

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guide de l'utilisateur

LONGER

LONGER LK4 Pro Manuel utilisateur