Ultimaker 3 Extended Mode d’emploi

Ultimaker Support

›

3D Printers

›

Ultimaker 3

›

Maintenance

Check for play on the axles of the

Ultimaker 3

January 28, 2020 10:31

The four X and Y axles are locked in place by the pulleys. However, it is possible that one

or more of the pulleys can become slightly loose over time, which could affect their

alignment. If this is the case, there could be play on the X and/or Y axles which can cause

issues with print quality.

It is recommended to check for play on the axles at least once every three months.

Start with the right X axle. Place the print head in the back-left corner of the printer to

keep it out of the way. Hold the frame of the Ultimaker 3 with one hand, and firmly hold

the right X axle with the other. Attempt to move the axle forwards and backwards; do

not be afraid to apply too much force.

Ultimaker

Ask our community of experts

Go to our community











Check for play on the axles of the Ultimaker 3 – ... https://support.ultimaker.com/hc/en-us/articles/...

1 of 3 12/15/20, 1:54 PM

Comments

0 comments

Article is closed for comments.

Articles in this section

Repeat this for the other axles. Make sure to move the print head to the opposite side

each time.

The axles should not move at all. If one of the axles does move, you can observe a

ticking noise of the pulleys hitting the frame. In this case it is recommended to

calibrate

the print head

Was this article helpful?





0 out of 8 found this helpful



Update the Ultimaker 3 firmware



Ultimaker 3 firmware release notes



Replace the build plate clamps of the Ultimaker 3



Replace the radial fans of the Ultimaker 3



Replace the axial fan of the Ultimaker 3



Replace the tube coupling collet of the Ultimaker 3



Replace the clamp clip of the Ultimaker 3



Replace the Bowden tubes on the Ultimaker 3



Clean the feeders on the Ultimaker 3



Lubricate the lead screw of the Z motor on the Ultimaker 3

Check for play on the axles of the Ultimaker 3 – ... https://support.ultimaker.com/hc/en-us/articles/...

2 of 3 12/15/20, 1:54 PM

Recently viewed articles



Lubricate the Ultimaker 3 axles



Cleaning the Ultimaker 3



Ultimaker 3 maintenance schedule

Check for play on the axles of the Ultimaker 3 – ... https://support.ultimaker.com/hc/en-us/articles/...

3 of 3 12/15/20, 1:54 PM

Autres manuels pour 3 Extended

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Ultimaker Imprimante 3D

Ultimaker

Ultimaker 2 Extended Manuel utilisateur

Ultimaker

Ultimaker 3 Extended Guide de configuration

Ultimaker

Ultimaker 3 Extended Manuel utilisateur

Ultimaker

Ultimaker S5 Material Station Manuel utilisateur

Ultimaker

Ultimaker 2 Extended Manuel d'utilisation et d'entretien

Ultimaker

Ultimaker S5 Material Station Manuel utilisateur

Ultimaker

Ultimaker 2 Extended Manuel utilisateur

Ultimaker

Ultimaker EXTRUSION UPGRADE Manuel utilisateur

Ultimaker

Ultimaker 2+ Connect Manuel d'utilisation et d'entretien

Ultimaker

Ultimaker 2 Extended Manuel utilisateur

Ultimaker

Ultimaker 3 Extended Manuel utilisateur

Ultimaker

Ultimaker 2 Extended Manuel utilisateur

Ultimaker

Ultimaker 2 Extended Manuel utilisateur

Ultimaker

Ultimaker EXTRUSION UPGRADE Manuel utilisateur

Ultimaker

Ultimaker 3 Extended Manuel utilisateur

Ultimaker

Ultimaker 3 Extended Guide de configuration

Ultimaker

Ultimaker S3 Manuel utilisateur

Ultimaker

Ultimaker Ultimaker S5 Pro Bundle Manuel utilisateur

Ultimaker

Ultimaker S5 Material Station Manuel utilisateur

Ultimaker

Ultimaker S5 Material Station Manuel utilisateur

Ultimaker

Ultimaker S5 Material Station Manuel utilisateur

Ultimaker

Ultimaker 3 Extended Mode d’emploi

Ultimaker

Ultimaker 3 Extended Instructions de fonctionnement

Ultimaker

Ultimaker Original Manuel utilisateur

Manuels Imprimante 3D populaires d'autres marques

EcubMaker

EcubMaker TOYDIY Manuel utilisateur

AnyCubic

AnyCubic Kossel Plus Manuel utilisateur

ReDeTec

ReDeTec ProtoCycler Manuel utilisateur

Kywoo3D

Kywoo3D Tycoon IDEX Manuel utilisateur

CraftBot

CraftBot PLUS PRO Manuel utilisateur

3DGence

3DGence INDUSTRY F340 Manuel utilisateur

HP Jet Fusion 4200 Mode d'emploi

Rokit

Rokit AEP Series Manuel utilisateur

AnkerMake

AnkerMake M5 Manuel utilisateur

DIYElectronics

DIYElectronics PRUSA I3 Instructions de montage

Ackuretta

Ackuretta FreeShape 120 Manuel utilisateur

LONGER

LONGER LK5Pro Manuel utilisateur

Stratasys

Stratasys J850 Manuel utilisateur

MakerBot

MakerBot Replicator Manuel utilisateur

Stratasys

Stratasys FDM Vantage Series Manuel utilisateur

ZYYX

ZYYX Pro II Manuel utilisateur

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guide de l'utilisateur

LONGER

LONGER LK4 Pro Manuel utilisateur