Ubiquiti UniFi UAP--AC--HD Manuel utilisateur
802.11ac Wave 2
Enterprise Wi-Fi Access Point
Model: UAP-AC-HD
Introduction
Thank you for purchasing the Ubiquiti Networks®
UniFi®802.11ac Wave 2 Enterprise Wi-Fi Access Point.
This Quick Start Guide is designed to guide you through
installation and includes warranty terms.
IMPORTANT: The UAP-AC-HD requires the UniFi Controller
v5.3 or newer, available at: downloads.ubnt.com/unifi
Package Contents
UniFi AP AC HD Mounting Bracket Ceiling Backing Plate
Flat Head Screws
(Qty. 4)
Keps Nuts
(Qty. 4)
Screws
(Qty. 4)
Screw Anchors
(Qty. 4)
802.11ACWave 2
AccessPoint
Model:UAP-AC-HD
Gigabit PoE* (48V, 0.5A)
with Mount Bracket
Power Cord* Quick Start
Guide
* Included only in the single-pack of the UAP-AC-HD
TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet
cable and earth grounding must be used as conditions of product warranty. TOUGHCable™
is designed for outdoor installations. It is the customer’s responsibility to follow local country
regulations, including operation within legal frequency channels, output power, and Dynamic
Frequency Selection (DFS) requirements.
Installation Requirements
• Phillips screwdriver
• Drill and drill bit (6 mm for wall-mounting or 3 mm for
ceiling-mounting)
• Optional: Drywall or keyhole saw (to cut 18 mm hole for
Ethernet cable feed)
• Cat5/6 UTP cable for indoor installations
Outdoor Installation Requirements
IMPORTANT: The UAP-AC-HD may be installed outdoors
under an eave or other protected location. Do not
install the UniFi AP in an open environment.
• Mounting location should be at least 60 cm (2 ft) from the
edge of the eave or ceiling.
• Cable feed opening must be directed away from the open
environment.
• Cable feed must be pointed downwards when wall-mounted.
• Shielded Category 5 (or above) cabling should be used
for all outdoor wired Ethernet connections and should be
grounded through the AC ground of the PoE.
We recommend that you protect your networks from
harmful outdoor environments and destructive ESD events
with industrial-grade, shielded Ethernet cable from Ubiquiti
Networks. For more details, visit
www.ubnt.com/toughcable
System Requirements
• Linux, MacOSX, or Microsoft Windows 7/8/10
• Java Runtime Environment 1.6 (1.8 or newer recommended)
• Web Browser: Google Chrome (Other browsers may have
limited functionality.)
• UniFi Controller software v5.3 or newer (available at:
downloads.ubnt.com/unifi)
Network Topology Requirements
• A DHCP-enabled network (for the AP to obtain an IP address
as well as for the wireless clients after deployment)
• A UniFi Cloud Key or management station running the UniFi
Controller v5.3 (or newer) software, located either on-site
and connected to the same Layer 2 network, or off-site in the
cloud or NOC
US-16-150W
USG-PRO-4
(DHCP Server)
Internet
UAP-AC-HD
UAP-AC-M-PRO
UAP-AC-PRO
LAN
WAN
UniFi Hybrid
Cloud Install
Remote Access to
UniFi Controller
Sample Network Diagram
All UniFi devices support off-site management controllers.
For setup details, see the User Guide on the website:
documentation.ubnt.com/unifi
Hardware Overview
LED
LED Color Status
White Factory default, waiting to be integrated.
Flashing White Initializing.
Alternating
White/Blue
Device is busy; do not touch or unplug it.
This usually indicates that a process such
as a firmware upgrade is taking place.
Blue
Indicates the device has been successfully
integrated into a network and is working
properly.
Quickly
Flashing Blue
This is used to locate an AP.
When you click Locate in the UniFi
Controller software, the AP will flash. It
will also display the location of the AP on
the map.
Steady Blue
with occasional
flashing
Indicates the device is in an isolated state
(all WLANs are brought down until an
uplink is found).
Ports
Main
Port
Secondary
Port
Security
Slot
Reset
Button
USB 3C
Port
Reset The Reset button serves two functions for the UniFi AP:
• Restart Press and release the Reset button quickly.
• Restore to Factory Default Settings Press and hold the
Reset button for more than five seconds.
USB 3C The USB 3C port is reserved for future use.
Secondary The Secondary port is a Gigabit Ethernet port used
for bridging.
Main The Main port is a Gigabit Ethernet port used to
connect the power and should be connected to the LAN and
DHCPserver.
IMPORTANT: The UAP-AC-HD cannot be powered by the
US-8 or US-8-60W; however, it can be powered by other
UniFi PoE Switches that provide 802.3at PoE+power.
Note: If you need to remove the UniFi AP from the
Mounting Bracket, insert a straightened paper clip in the
Security Slot to release the Lock Tab and turn the UniFi
AP counterclockwise.
Upgrade from UAP-AC-PRO
The UAP-AC-HD uses the same mounting hardware as the
UAP-AC-PRO, so you only need to remove the UAP-AC-PRO
and replace it with the UAP-AC-HD.
To begin the upgrade, perform the following steps:
1. Insert a straightened paper clip into the UAP-AC-PRO
Security Slot to disengage the lock. Then turn the
UAP-AC-PRO counterclockwise and lift it off of the
mounting bracket.
Security Slot
UAP-AC-PRO (wall mount installation)
2. Unplug the Ethernet cable from the Main port.
3. Go to step 4 of the Wall Mount section or step 5 of the
Ceiling Mount section.
Hardware Installation
The UniFi AP can be mounted on the wall or ceiling. Perform
the steps for the appropriate installation:
Wall Mount
1. Position the Mounting Bracket at the desired location on
the wall with the Arrow pointing up.
2. Mark the four mounting holes, and use a 6 mm drill bit to
drill the holes. If your Ethernet cable feeds through the
wall, cut or drill a circle approximately 18 mm in diameter.
Then feed the CAT5/6 cable through the hole.
Arrow
Optional 18 mm Hole for
Ethernet Cable Feed through the Wall
3. Insert the Screw Anchors into the holes. Secure the
Mounting Bracket to the wall by inserting the Screws into
the anchors.
4. Remove the rubber port cover from the UniFi AP.
5. If the Ethernet cable is fed through the wall, skip to step6.
If the Ethernet cable runs along the mounting surface,
remove the cable feed plug.
6. Feed the Ethernet cable through the port cover.
Note: The feed hole will stretch to accommodate the
RJ45 connector, and then seal around the cable.
7. Connect the Ethernet cable to the Main port and replace
the port cover.
Autres manuels pour UniFi UAP--AC--HD
1
Table des matières
Autres manuels Ubiquiti Point d'accès sans fil
Ubiquiti
Ubiquiti PBE-M5-620 Manuel utilisateur
Ubiquiti
Ubiquiti NanoStation M Manuel utilisateur
Ubiquiti
Ubiquiti UniFi Manuel utilisateur
Ubiquiti
Ubiquiti UniFi nanoHD AP Manuel utilisateur
Ubiquiti
Ubiquiti AirOS B2 Manuel utilisateur
Ubiquiti
Ubiquiti NBE--2AC--13 Manuel utilisateur
Ubiquiti
Ubiquiti UniFi UAP-IW-HD Manuel utilisateur
Ubiquiti
Ubiquiti UAP-Outdoor-5 Manuel utilisateur
Ubiquiti
Ubiquiti UniFi AP AC Lite Manuel utilisateur
Ubiquiti
Ubiquiti airFiber AF-11 Manuel utilisateur
Ubiquiti
Ubiquiti NanoStationM Series Manuel utilisateur
Ubiquiti
Ubiquiti PowerBeam AC GENZ Manuel utilisateur
Ubiquiti
Ubiquiti RP-5AC-Gen2 Manuel utilisateur
Ubiquiti
Ubiquiti UAP-IW Manuel utilisateur
Ubiquiti
Ubiquiti UniFi AP AC Lite Manuel utilisateur
Ubiquiti
Ubiquiti NanoBeam ac NBE-5AC-16 Manuel utilisateur
Ubiquiti
Ubiquiti NanoStation NSM2 Manuel utilisateur
Ubiquiti
Ubiquiti NanoStation loco Manuel utilisateur
Ubiquiti
Ubiquiti Bullet AC-IP67 Manuel utilisateur
Ubiquiti
Ubiquiti UniFi UAP-AC-LR-5-EU Manuel utilisateur
Manuels Point d'accès sans fil populaires d'autres marques
D-Link
D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur
Cisco
Cisco Aironet 1550 Series Manuel utilisateur
Aruba
Aruba IAP-335 Manuel utilisateur
Advantek Networks
Advantek Networks AWN-AP-54MR Manuel utilisateur
IP-COM
IP-COM AP355 Manuel utilisateur
Buffalo
Buffalo AirStation WLA-L11G Manuel utilisateur
