Ubiquiti GBE Manuel utilisateur

7. 2. 2020 GBE Quick Start Guide

https://dl.ui.com/qsg/GBE/GBE_EN.html 1/18

GBE Ball Joint Mount Lock Ring

Metal Strap Gigabit PoE (24V, 0.5A) with

Mounting Bracket

Power Cord

Package Contents

Installation Requirements

Clear line of sight between GigaBeam AP and station

Pole-mounting: 7 mm socket wrench or screwdriver

Wall-mounting: wall fastener (not included)

Shielded Category 5 (or above) cabling with drain wire should be used for all wired

Ethernet connections and should be grounded through the AC ground of the PoE.

We recommend that you protect your networks from harmful outdoor

environments and destructive ESD events with industrial-grade, shielded Ethernet

cable from Ubiquiti. For more details, visit ui.com/toughcable

Surge protection should be used for all outdoor installations. We recommend that

you use two Ethernet Surge Protectors, model ETH-SP-G2, one near the device

and the other at the entry point to the building. The ETH-SP-G2 will absorb power

surges and safely discharge them into the ground.

Note: For guidelines about grounding and lightning protection, follow your

local electrical regulatory codes.

GBE Quick Start Guide

7. 2. 2020 GBE Quick Start Guide

https://dl.ui.com/qsg/GBE/GBE_EN.html 2/18

Reset Button

PoE IN Port

Hardware Overview

To reset to factory defaults, press and hold the Reset button for more than 10

seconds while the device is powered on. Alternatively, the device may be reset

remotely via a Reset button located on the bottom of the Gigabit PoE Adapter.

This Gigabit Ethernet port is used to connect the power and should be connected

to the LAN and DHCP server.

GBE Quick Start Guide

7. 2. 2020 GBE Quick Start Guide

https://dl.ui.com/qsg/GBE/GBE_EN.html 3/18

60 GHz LED

5 GHz LED

LAN LED

Power/Status LED

Lights steady blue when 60 GHz link is ready.

Lights steady blue when the 5 GHz link is ready.

The LED will light steady blue when an active Ethernet connection is made to the

Ethernet port and flash when there is activity.

Flashing White Bootup in progress.

White

Ready for use, not connected to Ubiquiti® Network

Management System (UNMS™). See “UNMS

Management”.

Blue Ready for use, connected to UNMS.

Steady Blue with

Occasional Flashing

Ready for use, unable to connect to UNMS, check

connection to UNMS server.

Quickly Flashing Blue Used to locate a device in UNMS.

Alternating

Blue/White Firmware upgrade in progress.

Hardware Installation

Go to the appropriate mounting instructions: Pole Mounting or “Wall Mounting”.

Pole-Mounting

GBE Quick Start Guide

7. 2. 2020 GBE Quick Start Guide

https://dl.ui.com/qsg/GBE/GBE_EN.html 4/18

Wall Mounting

The device must be mounted directly to a wood stud or other structurally stable

surface to avoid damage to the mounting hole when you adjust the aim.

Optional Accessory

To enhance stability, you can use the NanoBeam® Wall Mount Kit, model NBE-WMK

(sold separately).

GBE Quick Start Guide

7. 2. 2020 GBE Quick Start Guide

https://dl.ui.com/qsg/GBE/GBE_EN.html 5/18

Note: Center screw included. Two optional screws (not included) provide

additional stability.

Installation Instructions

GBE Quick Start Guide

7. 2. 2020 GBE Quick Start Guide

https://dl.ui.com/qsg/GBE/GBE_EN.html 6/18

Fastener (not included)

NanoBeam Wall Mount Kit

Aiming

Visually aim the GigaBeam radios at each other.

GBE Quick Start Guide

7. 2. 2020 GBE Quick Start Guide

https://dl.ui.com/qsg/GBE/GBE_EN.html 7/18

Connecting Power

GBE Quick Start Guide

7. 2. 2020 GBE Quick Start Guide

https://dl.ui.com/qsg/GBE/GBE_EN.html 8/18

WARNING: The switch port must comply with the power specifications

listed in “Specifications”.

GBE Quick Start Guide

7. 2. 2020 GBE Quick Start Guide

https://dl.ui.com/qsg/GBE/GBE_EN.html 9/18

Optional

Configuration

The device is set to DHCP by default, so it will try to automatically obtain an IP

address. If that fails, it will use the default fallback IP address, 192.168.1.20. Proceed

to the appropriate section, DHCP or “Fallback IP Address”:

DHCP

Use one of the following methods:

Set up the DHCP server to provide a specific IP address to the device based on

its MAC address (on the label).

Let the device obtain an IP address and then check the DHCP server to see which

IP address was assigned.

1. Connect a computer to your network and configure the Ethernet adapter on your

computer with a static IP address on the 192.168.1.x subnet.

2. Launch your web browser. In the address field, type: https://192.168.1.20

Then press enter (PC) or return (Mac).

3. Select your Country and Language. You must agree to the Terms of Use to use

the product. Click Continue.

GBE Quick Start Guide

7. 2. 2020 GBE Quick Start Guide

https://dl.ui.com/qsg/GBE/GBE_EN.html 10/18

4. Enter a Username and Password, confirm the Password, and click Save.

5. Click the icon.

6. Configure the following settings:

a. For one device, enable Access Point mode. For the other device (the Station),

keep Access Point disabled.

b. Enter a name in the SSID field. This must be the same on both the AP and the

Station.

c. In the WPA2 Preshared Key field, enter a combination of alphanumeric

characters (0-9, A-Z, or a-z).

7. Click Save Changes.

8. Configure each device (AP and Station) with a unique IP address:

a. Click the icon.

Note: The key is an alphanumeric password between 8 and 63

characters long.

GBE Quick Start Guide

Autres manuels pour GBE

Table des matières

Autres manuels Ubiquiti Point d'accès sans fil

Ubiquiti

Ubiquiti PowerBeam AC PBE-5AC-620 Manuel utilisateur

Ubiquiti

Ubiquiti RP-5AC-Gen2 Manuel utilisateur

Ubiquiti

Ubiquiti NanoStationM Series Manuel utilisateur

Ubiquiti

Ubiquiti NanoBeam M5 Manuel utilisateur

Ubiquiti

Ubiquiti RocketM Series Manuel utilisateur

Ubiquiti

Ubiquiti UAP-AC Manuel utilisateur

Ubiquiti

Ubiquiti UAP-AC-PRO Manuel utilisateur

Ubiquiti

Ubiquiti UAP-AC-HD Manuel utilisateur

Ubiquiti

Ubiquiti NBE--2AC--13 Manuel utilisateur

Ubiquiti

Ubiquiti Rocket R5ACL Manuel utilisateur

Ubiquiti

Ubiquiti PrismStation 5AC Manuel utilisateur

Ubiquiti

Ubiquiti PowerBeam PBE-5AC400 Manuel utilisateur

Ubiquiti

Ubiquiti UniFi UAP-AC-LITE Manuel utilisateur

Ubiquiti

Ubiquiti Loco5AC Manuel utilisateur

Ubiquiti

Ubiquiti UAP-AC-PRO Manuel utilisateur

Ubiquiti

Ubiquiti nano station M Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation 5AC Loco Manuel utilisateur

Ubiquiti

Ubiquiti NBE--2AC--13 Manuel utilisateur

Ubiquiti

Ubiquiti AirOS B2 Manuel utilisateur

Ubiquiti

Ubiquiti PBE-M5-300-US Manuel utilisateur

Ubiquiti

Ubiquiti U-Installer Manuel utilisateur

Ubiquiti

Ubiquiti UAP-AC-IW Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation M2 Manuel utilisateur

Ubiquiti

Ubiquiti airFiber AF-11 Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur

Draytek

Draytek VIGORAP 902 Manuel utilisateur

EnGenius

EnGenius EAP350 Manuel utilisateur