Ubiquiti EdgeRouter 12 Manuel utilisateur

10-Port Gigabit Router with PoE

Passthrough and 2 SFP Ports

Model: ER-12

Introduction

Thank you for purchasing the Ubiquiti Networks®

EdgeRouter™. This Quick Start Guide is designed to guide you

through installation and also includes warranty terms.

Package Contents

EdgeRouter ER-12

Wall Mount

Screws (Qty. 2)

Wall Mount

Anchors (Qty. 2)

Ground

Screw

Power Adapter

(24V, 1A)

Cable Clip

Installation Requirements

• For indoor applications, use Category 5 (or above) UTP

cabling approved for indoor use.

• For outdoor applications, shielded Category 5 (or above)

cabling should be used for all wired Ethernet connections

and should be grounded through the AC ground of the

power supply.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial-grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit:

www.ubnt.com/toughcable

WARNING: To reduce the risk of fire or electric shock,

do not expose the EdgeRouter to rain or moisture.

Note: Although the cabling can be located outdoors,

the EdgeRouter itself should be housed inside a

protective enclosure.

Hardware Overview

Front Panel Ports

Console RJ45 (Ports 0-9) SFP Ports

USB

Interface Description

Console

RJ45 serial console port for Command

Line Interface (CLI) management. Use an

RJ45-to-DB9, serial console cable, also

known as a rollover cable, to connect the

Console port to your computer. (If your

computer does not have a DB9 port,

then you will also need a DB9 adapter.)

Then configure the following settings as

needed:

• Baud rate 115200

• Data bits 8

• Parity NONE

• Stop bits 1

• Flow control NONE

USB Reserved for future use.

RJ45

(Ports 0 - 9)

All RJ45 ports can be used for routing

and support 10/100/1000 Mbps Ethernet

connections. Ports 0 - 7 can be configured

for switching functions using the EdgeOS

Configuration Interface. Port 0 supports

24V Passive PoE In and port 9 supports

optional Passive PoE Out (disabled by

default).

SFP Ports

(Ports 10 - 11)

SFP routing ports are hot-swappable and

support Gigabit fiber SFP modules.

Front Panel Button

Reset

Button Description

Reset

There are two methods to reset the

EdgeRouter to factory defaults:

• Runtime reset (recommended) The

EdgeRouter should be running after

bootup is complete. Press and hold the

Reset button for about 10seconds until

the LED for port eth9 starts flashing and

then becomes solidly lit. After a few

seconds, the LED will turn off, and the

EdgeRouter will automatically reboot.

• Power-on reset Disconnect the Power

Cord from the Power Adapter. Press and

hold the Reset button while connecting

the power (refer to “Connecting Power”

for details). The port LEDs will light up

in sequential order. Keep holding the

Reset button until the System LED starts

flashing blue and white, and then release

the button.

Front Panel LEDs

System

System LED

Note: The System LED functionality has been updated

with firmware v1.10.7. We recommend that you update

the EdgeRouter to the latest firmware.

State Status

Flashing White Bootup in progress.

White

Ready for use, not connected to Ubiquiti®

Network Management System (UNMS™).

See “UNMS Management”.

Blue Ready for use, connected to UNMS.

Steady Blue

with Occasional

Flashing

Ready for use, unable to connect to

UNMS, check connection to UNMSserver.

Quickly Flashing

Blue Used to locate a device in UNMS.

Alternating

Blue/White Firmware upgrade in progress.

Speed/Link/Act PoE Link/Act

RJ45 LEDs

LED State Status

PoE

Off No PoE

Green 24V 2-Pair Passive PoE Output

Speed/

Link/

Activity

Off No Link

Amber Link Established at 10/100 Mbps

Amber

Flashing Link Activity at 10/100 Mbps

Green Link Established at 1000 Mbps (1 Gbps)

Green

Flashing Link Activity at 1000 Mbps (1Gbps)

SFP LED

LED State Status

Link/Act

Off No Link

Green Link Established at 1 Gbps

Green

Flashing Link Activity at 1Gbps

Back Panel

Grounding Point

Ventilation Holes Power

Note: There are additional ventilation holes on the sides

of the EdgeRouter.

Hardware Installation

WARNING: FAILURE TO PROVIDE PROPER VENTILATION

MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF

CLEARANCE NEXT TO THE VENTILATION HOLES FOR

ADEQUATE AIRFLOW.

Wall Mounting

To mount the EdgeRouter on a wall, you will need a drill, a

6mm drill bit, and a Phillips screwdriver.

1. Use a 6 mm drill bit to drill two holes 190 mm apart.

2. Insert the Wall Mount Anchors into the holes. Use a Phillips

screwdriver to secure a Wall Mount Screw to each anchor.

Leave a clearance of approximately 3 mm between each

screw head and its anchor.

190 mm

3 mm

Note: You can also mount the EdgeRouter in a

vertical orientation.

3. Position the EdgeRouter with the Ethernet ports facing

down. Place the wall-mount slots of the EdgeRouter over

the screw heads on the wall. Then slide the EdgeRouter

down to lock it into place.

Grounding the EdgeRouter (Recommended)

The EdgeRouter is grounded through the Power Adapter;

however, you can add optional ESD grounding for enhanced

ESD protection.

1. Attach the Ground Screw to secure a ground wire (not

included) to the Grounding Point.

2. Optional: To secure the Power Adapter cord, insert it

into the Cable Clip and secure the Cable Clip using the

GroundScrew.

3. Secure the other end of the ground wire to a grounding block.

Connecting Power

1. Connect the Power Adapter to the Power port.

2. Connect the other end of the Power Adapter to a power

outlet.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Ubiquiti Routeur réseau

Ubiquiti

Ubiquiti airCube Mode d’emploi

Ubiquiti

Ubiquiti airCube Manuel utilisateur

Ubiquiti

Ubiquiti EdgeRouter 10X Manuel utilisateur

Ubiquiti

Ubiquiti Edge Pro ERPro-8 Manuel utilisateur

Ubiquiti

Ubiquiti ER-8-XG Manuel utilisateur

Ubiquiti

Ubiquiti EdgeRouter PoE ERPoe-5 Manuel utilisateur

Ubiquiti

Ubiquiti UniFi AP PRO Manuel utilisateur

Ubiquiti

Ubiquiti EdgeRouter X ER-X Manuel utilisateur

Ubiquiti

Ubiquiti LiteStation2 Manuel utilisateur

Ubiquiti

Ubiquiti UniFi Security Gateway PRO Manuel utilisateur

Ubiquiti

Ubiquiti EdgeRouter ER-8 Manuel utilisateur

Ubiquiti

Ubiquiti EdgeRouter ER-12P Manuel utilisateur

Ubiquiti

Ubiquiti EdgeRouter 6P Manuel utilisateur

Ubiquiti

Ubiquiti TS-5-POE ToughSwitchPoE Manuel utilisateur

Ubiquiti

Ubiquiti EdgeRouter PoE ERPoe-5 Manuel utilisateur

Ubiquiti

Ubiquiti UCK-G2 Manuel utilisateur

Ubiquiti

Ubiquiti EdgeRouter 6P Manuel utilisateur

Ubiquiti

Ubiquiti EdgeRouter LITE Manuel utilisateur

Ubiquiti

Ubiquiti ER-12 Manuel utilisateur

Ubiquiti

Ubiquiti Amplifi AFi-LR Manuel utilisateur

Ubiquiti

Ubiquiti AFi-ALN Manuel utilisateur

Ubiquiti

Ubiquiti 3GStation Professional Manuel utilisateur

Ubiquiti

Ubiquiti ROcket M5 Manuel utilisateur

Ubiquiti

Ubiquiti TS-8-PRO Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité