U-Line H-1993 Manuel utilisateur

PAGE 1 OF 3 0714 IH-1993

πH-1993

KIHLBERG MANUAL

CARTON STAPLER

1-800-295-5510

uline.com

ADJUSTING THE STAPLE LEG LENGTH

The stapler is adjustable for 5/8"-3/4" staples. The stapler

setting for a different staple leg length is altered as

follows. Start by adjusting the depth of stapling for deep

clinching (=). (See Figure 2)

1. With the allen wrench,

unscrew locking screw (A)

two turns. (See Figure 1)

2. With a screwdriver, adjust

screw (B) to 5/8" or 3/4" leg

length. (See Figure 1)

3. Tighten the locking

screw (A). (See Figure 1)

ADJUSTING THE PENETRATION DEPTH

The depth of stapling is

easily adjusted by using the

setting knob (1). Press the

knob in and turn it to the

desired position.

(See Figure 2)

• Use "–" for shallow

stapling penetration.

• Use "=" for deep stapling

penetration.

ADJUSTING STAPLE CLINCH

It is possible to adjust how tightly the staples are closing:

1. With the allen wrench,

turn the adjusting screw

clockwise for a stronger

clinch. (See Figure 3)

2. Turn the adjusting screw

counterclockwise to

open the clinch more.

CONTROLLING THE CLINCH (See Figure 4)

A. Good clinch.

B. Leg length of the

staple too long or

bent too much.

C. Leg length of staple

too short or not bent

enough.

If necessary, adjust

staple clinch.

NOTE: Always use Josef Kihlberg original

staples – S-10720 (5/8") or S-10721 (3/4").

Adjusting

Screw

Figure 3

Figure 4

3/4" 5/8"

Figure 1

Figure 2

TOOL NEEDED COMPATIBLE STAPLES

Allen Wrench

(Included)

S-10721

C34

1⁄ x 3/4"

S-10720

C58

1⁄ x 5/8"

PAGE 2 OF 3 0714 IH-1993

LOADING THE STAPLER

NOTE: Always use Josef Kihlberg original

staples – S-10720 (5/8") or S-10721 (3/4").

The correct type of staple is marked on the left hand

side of the magazine. Be sure to use the correct staple

length for your application and that ensure the stapler is

adjusted for this length.

1. Pull the pusher all the way

out. (See Figure 5)

2. Place three staple strips

into the magazine from

the top. (See Figure 6)

3. Lift the pusher to release.

Carefully move the pusher

forward until it reaches the

staples. (See Figure 7)

LOADING CONTINUED

OPERATION

MAINTENANCE

OPERATING THE STAPLER

WARNING! Always place yourself in a firmly

balanced position when using or handling

the stapler.

• Press the stapler against the cardboard.

• Pull the handle firmly.

• Move the stapler and repeat until you have

finished stapling.

• Control the clinch regularly. Adjust when necessary.

WARNING! Before stapling, ensure that your

hand or any other part of your body is not

underneath the staple discharge area.

Staple Strip

Figure 6

Pusher

Figure 5

Pusher

Figure 7

CLEANING THE STAPLER

This stapler does not require special servicing. It

only needs regular cleaning with a non-aggressive

(non-corrosive) cleaning agent.

NOTE: Do not remove any parts for cleaning

purposes.

NOTE: Check the proper functioning of all

safety devices daily. Make sure that all screws

and nuts are securely tightened.

REMOVING JAMMED STAPLES

To remove a jammed staple:

1. Unscrew 6 screws at the rear body. (See Figure 8)

2. Remove rear body and the defective staple.

(See Figure 9)

3. Assemble by reattaching the rear body with

6 screws. (See Figure 8)

Allen

Wrench

Figure 8 Figure 9

PAGE 3 OF 3 0714 IH-1993

REPLACING THE DRIVER BLADE/ANVILS

TO REPLACE THE DRIVER BLADE:

1. Remove six screws

holding the rear

body to the front

section. (See Figure 10)

2. Remove the rear

body with magazine.

3. Replace the driver

blade. (See Figure 11)

4. Assemble parts in

reverse order.

NOTE: If changing the anvils, always change

both at the same time.

TO REPLACE THE ANVILS:

1. Remove the driver

blade (See Figure 11)

2. Remove the screws.

3. Replace the anvils.

4. Assemble parts in

reverse order.

MAINTENANCE CONTINUED

Rear Body

Screw

Figure 10

Screw

Anvils

Driver

Blade

Screw

Figure 11

πCHICAGO•ATLANTA•DALLAS•LOSANGELES•MINNEAPOLIS•NYC/PHILA•SEATTLE•MEXICO•CANADA

1-800-295-5510

uline.com

Autres manuels pour H-1993

Autres manuels U-Line Outils électriques

U-Line

U-Line SWINGLINE H-3067 Manuel utilisateur

U-Line

U-Line SWINGLINE LIGHT TOUCH H-2323 Manuel utilisateur

U-Line

U-Line H-491 Manuel utilisateur

U-Line

U-Line Н-863 Manuel utilisateur

U-Line

U-Line SHRINKFAST H-6098 Manuel utilisateur

U-Line

U-Line H-1028 Manuel utilisateur

U-Line

U-Line H-3070 Manuel utilisateur

U-Line

U-Line Shrinkfast 975 Manuel utilisateur

U-Line

U-Line H-995 Manuel utilisateur

U-Line

U-Line H-10157 Manuel utilisateur

U-Line

U-Line H-2027 Manuel utilisateur

U-Line

U-Line Swingline Light Touch H-2323 Mode d’emploi

U-Line

U-Line H-1024 Manuel utilisateur

U-Line

U-Line H-3070 Manuel utilisateur

U-Line

U-Line H-1481 Manuel utilisateur

U-Line

U-Line H-8094 Manuel utilisateur

U-Line

U-Line H-915 Manuel utilisateur

U-Line

U-Line H-915 Manuel utilisateur

U-Line

U-Line H-2028 Manuel utilisateur

U-Line

U-Line H-1302 Manuel utilisateur

U-Line

U-Line H-1030 Manuel utilisateur

U-Line

U-Line RIPACK 3000 Manuel utilisateur

U-Line

U-Line H-1024 Manuel utilisateur

U-Line

U-Line H-8094 Manuel utilisateur

Manuels Outils électriques populaires d'autres marques

AEG

AEG OMNI-JS Manuel utilisateur

SIP

SIP 01533 Manuel utilisateur

Ribimex

Ribimex PRS499 Manuel utilisateur

3M Fiber Optic Connector Crimp Tool Manuel utilisateur

Ryobi

Ryobi P524 Manuel utilisateur

ROJEK

ROJEK FSN 300A Manuel utilisateur

Kemper

Kemper 1740PRO Manuel utilisateur

WABCO

WABCO OptiTire Manuel utilisateur

EINHELL

EINHELL TE-MS 18/210 Li Manuel utilisateur

Orgapack

Orgapack OR-T 85 Guide rapide

TOUGHCUT

TOUGHCUT Diamond 400 Manuel utilisateur

Yaros

Yaros PB-3603 Manuel utilisateur

Fein

Fein BSS 2.0 E Guide de configuration

Baileigh Industrial

Baileigh Industrial SS-2725 Manuel utilisateur

Milwaukee

Milwaukee 2674-20 Manuel utilisateur

Fein

Fein BLs 1.6 Manuel utilisateur

Princess

Princess Electric Multi Sharpener Manuel utilisateur

FOREDOM

FOREDOM K.1050 Manuel