U-Line H-1028 Manuel utilisateur

PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com

AIR DRIVE CARTON STAPLER

MODEL: H-1028

MANUAL

WARNING

Before operating this stapler familiarize yourself with the safety warnings and

instructions in this manual. Keep these instructions with the stapler for future

reference. If you have any questions, contact Uline at 1-800-295-5510.

CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS

PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com

Table of Contents

Tool Specifications

Safety Instructions

Lubrication & Maintenance

Air Supply & Connections

Loading the Tool

Checking the Staple Leg Length

Clinch Adjustment

Depth Adjustment

Tool Operation

Cleaning the tool

Clearing Tool Jams

Troubleshooting

Teeth Replacement

Driver Replacement

Pusher Spring Replacement

Valve & Tube O-Ring Replacement

Piston Replacement

CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS

PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com

Tool Specifications

Model of Tool H-1028

ADB 18-32

Dimensions: LxHxW 13.5x8.75x6

Weight (without Fasteners) 6lbs

Compressed Air:

Maximum PSI: 110 psi

Recommended Operating Pressure: 71-100 PSI

Air Consumption:

Staple Specification: S-1396 C34 Stick

Staple Specification: S-289 C58 Stick

Staple Capacity: 100 staples

Noise Levels:

CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS

PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com

SAFETY INSTRUCTIONS

1. Read the manual and understand all safety instructions before operating the

tool. If you have questions, contact Uline at 1-800-295-5510.

2. Never use flammable gases as a power source for the stapler. Only use

filtered, compressed air.

3. Never use gasoline or other flammable liquids to clean the stapler. Vapors

left on the stapler could ignite and cause the tool to explode

4. Do not exceed 110 psi of air pressure when operating the stapler.

5. Disconnect the stapler for the air supply before making adjustments,

cleaning or clearing jams and when not in use.

6. Do not pull the trigger when carrying or holding the stapler.

7. Never carry the stapler by the hose or pull on the hose to move the stapler.

8. Always wear protective equipment, i.e. safety glasses, hearing protection

and head protection.

9. Do not use a check valve or any other fitting which allows air to remain in the

stapler.

10.Do not place your hand or any other body part in the staple clinching area or

adjustment window when connecting or disconnecting the air supply.

11.Never point the stapler at yourself or anyone else.

CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS

PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com

Lubrication & Maintenance:

1. Lubricate the stapler prior to initial operation.

2. Disconnect the stapler from the air supply prior to servicing.

3. Turn the stapler so that the inlet is facing up and put one drop of high-speed

spindle oil, UNOCOL RX22, or 3-in-1 oil into air inlet. Never use detergent

oil or additives.

4. Operate the tool briefly after adding oil.

5. Wipe off excessive oil at the exhaust. Excessive oil will damage the O-rings.

If inline oiler is used, manual lubrication through the air inlet is not required

on a daily basis.

Air supply and Connections

NOTE:

The following illustration shows the correct mode of connection to the air supply

system which will increase the efficiency and life of the stapler.

Many air tool users find it convenient to use an inline oiler to provide oil circulation

through their tool. Check oil level in the oiler daily.

A filter is recommended on your air compressor. Check the filter and drain on a

daily basis.

CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS

PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com

Loading the Tool

1. Disconnect the air supply.

2. Pull the Pusher back until it stops on pusher pivots. Rotate pusher to

position.

3. Insert 2 sticks of appropriate staples into the magazine. Let the sticks slide

forward to the front of the magazine.

4. Pull the pusher back to an upright position and gently let the pusher slide

forward against the staples. Do not let the pusher slide forward and strike

the staples at high speed as this may deform the staples and damage the

tool.

CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS

PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com

Staple Leg Length

1. Loosen the set screw with a 3mm Allen wrench.

2. Adjust 180°with a screw driver to the desired setting.

3. If you are using ¾” staples set L up.

4. If you are using 5/8” staples set S up. (diagram)

5. Tighten the set screw.

Clinch Adjustment

Use 2.5 mm Allen wrench and turn collar through window clockwise to tighten

clinch.

CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS

PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com

Depth Adjustment

1. Loosen front screw with a 6mm Allen wrench.

2. Push the body up and adjust to the desired depth.

3. When the top edge of the adjustment plate is at it’s highest setting the teeth

are at their shallowest penetration. If set at No. 1 the teeth are at their

deepest penetration.

CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS

PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com

Operating Instructions

Warning

1. Add a few drops of oil into the air inlet.

2. Install a quick connect fitting to the tool.

3. Regulate the air pressure to attain 80-100 psi.

4. Insert the staples into the tool following the loading instructions.

5. Reconnect the air hose to the tool.

6. Grasp the handle with one hand on box in line with the desired staple

location. There is a small projection on either side of the magazine seat as

an aid in locating the position of the staple.

7. The strongest closure requires staples close to the ends of the box.

Cleaning the Tool

Danger

1. Disconnect the Air Supply from the tool

2. Remove tar buildup with non-corrosive cleaner. Do not allow solvent to get

into the cylinder or damage may occur.

3. Dry the tool completely before use.

Never use gasoline or other flammable liquids to clean the stapler.

Vapors in the stapler could be ignited by a spark and cause the tool to explode.

1. Protect your eyes and ears. Wear:

a. Safety glasses with side shields

b. hearing protection.

Ensure that anyone in the vicinity wears safety protection.

2. To prevent accidental injuries never place a hand or any other body part in the staple

clinching area or adjustment window.

3. Never point the stapler towards you or anyone else.

4. Always handle the stapler with care. Never pull the trigger unless tool is ready for

operation.

5. Check and replace any damaged or worn components on the stapler.

CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS

PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com

Clearing a Jam

1. Disconnect Air Supply

2. Pull Pusher back and rotate to a locked position.

3. Insert needle nose pliers or screw driver to clear jam.

4. Slowly release Pusher back to position.

CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS

Table des matières

Autres manuels U-Line Outils électriques

U-Line

U-Line H-8094 Manuel utilisateur

U-Line

U-Line H-915 Manuel utilisateur

U-Line

U-Line RIPACK 3000 Manuel utilisateur

U-Line

U-Line H-1993 Manuel utilisateur

U-Line

U-Line H-10157 Manuel utilisateur

U-Line

U-Line H-1030 Manuel utilisateur

U-Line

U-Line H-1024 Manuel utilisateur

U-Line

U-Line H-995 Manuel utilisateur

U-Line

U-Line H-1993 Manuel utilisateur

U-Line

U-Line SWINGLINE LIGHT TOUCH H-2323 Manuel utilisateur

U-Line

U-Line Н-863 Manuel utilisateur

U-Line

U-Line SHRINKFAST 998 Manuel utilisateur

U-Line

U-Line H-491 Manuel utilisateur

U-Line

U-Line H-1335 Manuel utilisateur

U-Line

U-Line H-8094 Manuel utilisateur

U-Line

U-Line H-2028 Manuel utilisateur

U-Line

U-Line SHRINKFAST H-6098 Manuel utilisateur

U-Line

U-Line H-8094 Manuel utilisateur

U-Line

U-Line H-1026 Manuel utilisateur

U-Line

U-Line SWINGLINE H-3067 Manuel utilisateur

U-Line

U-Line H-1481 Manuel utilisateur

U-Line

U-Line H-2027 Manuel utilisateur

U-Line

U-Line H-491 Manuel utilisateur

U-Line

U-Line H-1302 Manuel utilisateur

Manuels Outils électriques populaires d'autres marques

AEG

AEG OMNI-JS Manuel utilisateur

SIP

SIP 01533 Manuel utilisateur

Ribimex

Ribimex PRS499 Manuel utilisateur

3M Fiber Optic Connector Crimp Tool Manuel utilisateur

Ryobi

Ryobi P524 Manuel utilisateur

ROJEK

ROJEK FSN 300A Manuel utilisateur

Kemper

Kemper 1740PRO Manuel utilisateur

WABCO

WABCO OptiTire Manuel utilisateur

EINHELL

EINHELL TE-MS 18/210 Li Manuel utilisateur

Orgapack

Orgapack OR-T 85 Guide rapide

TOUGHCUT

TOUGHCUT Diamond 400 Manuel utilisateur

Yaros

Yaros PB-3603 Manuel utilisateur

Fein

Fein BSS 2.0 E Guide de configuration

Baileigh Industrial

Baileigh Industrial SS-2725 Manuel utilisateur

Milwaukee

Milwaukee 2674-20 Manuel utilisateur

Fein

Fein BLs 1.6 Manuel utilisateur

Princess

Princess Electric Multi Sharpener Manuel utilisateur

FOREDOM

FOREDOM K.1050 Manuel