Tripp Lite SmartPro ST700HGL Manuel utilisateur

Owner’s Manual

SmartPro®

Medical-Grade UPS Systems

(with Lithium Iron Phosphate Batteries)

Models:

Important Safety Instructions 2

Package Contents 5

Connecting the Batteries 6

Quick Installation 7

Basic Operation 9

Guidance and Manufacturer’s Declaration 12

Storage and Service 13

Regulatory Compliance and 14

Product Registration

Español 15

Français 30

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

SMART700HGL

(Series Number: AG-8863) SMART1200XLHGL

(Series Number: AG-8862)

PROTECT YOUR INVESTMENT!

and ultimate peace of mind.

You could also win an

ISOBAR6ULTRA surge protector—

a $100 value!

www.tripplite.com/warranty

18-06-068-933608.indb 1 6/22/2018 4:56:25 PM

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be followed during the installation,

operation and storage of all Tripp Lite UPS Systems. Failure to heed these warnings may affect

your warranty.

Statement of Intended Use

Tripp Lite Medical-Grade UPS Systems are intended to support and protect non-medical and

medical computer equipment and medical devices that require leakage current reduction, surge

protection, voltage regulation, line noise ﬁltering and battery backup during power outages and

generator testing, both inside and outside patient care areas. Tripp Lite Medical-Grade UPS Systems

come with hospital-grade plugs and receptacles that reduce leakage to below 100μA.

Product Information

SMART700HGL SMART1200XLHGL

AC Input Voltage 120 120

AC Input Voltage Range 81–143 81–143

Input Amp(s) 5.5 9.2

Output Amp 5.8 6.25

Rated Power (VA/Watts) 700VA/450W 1000VA/750W

Frequency 60 Hz 60 Hz

No. of Phases Single Single

Class Type Class I Class I

Plug/Connector Type C14 Inlet Dongle, 6 in. C14 Inlet Dongle, 6 in.

Operation Continuous Continuous

AC Input Protection (Qty./type/rating) Input breaker

(2 x 10A), thermal Input breaker

(2 x 15A), thermal

Max Leakage Current (uA) Less than 100uA Less than 100uA

Weight 33.7 lb. (15.3 kg) 33.6 lb. (15.2 kg)

Known Contraindication None None

UPS Location Warnings

Relevant Symbols

Denotes that information in the manual should be reviewed before use.

Used to signal a warning that a statement is particularly important and could pose a safety

risk.

Warning—Dangerous Voltage No sitting

Denotes general warning sign No stepping on surface

Refer to Instruction Manual/Booklet No pushing

18-06-068-933608.indb 2 6/22/2018 4:56:25 PM

Important Safety Instructions

• Do not use this equipment within oxygen-enriched atmospheres, or within 1 ft. (0.3 m) of a point

at which an oxygen-enriched atmosphere is intentionally vented.

• Use caution when lifting UPS. Because of the considerable weight of all UPS systems, at least

two people should assist in lifting and installing them.

• Install the UPS indoors, away from excess moisture or heat, dust or direct sunlight.

• For best performance, the UPS should be used in a location that meets the following conditions:

Temperature: 32 to 104° F (0 to 40° C); Humidity: 0 to 95% (non-condensing);

Elevation: <6,562 ft. (2,000 m) above sea level.

• Leave adequate space around all sides of the UPS for proper ventilation. Do not obstruct its vents

or fan openings.

• Do not mount unit with its front or rear panel facing down (at any angle). Mounting in this manner

will seriously inhibit the unit’s internal cooling, eventually causing product damage not covered

under warranty.

• UPS is not intended for patient contact. Avoid installation that will cause accidental patient

contact.

UPS Connection Warnings

• The UPS contains its own energy source (battery). The output terminals may be live even when

the UPS is not connected to an AC supply.

• Connect the UPS to a properly grounded AC power outlet. Do not modify the UPS plug in a

way that would eliminate its connection to ground. Do not use adapters that eliminate the UPS

connection to ground.

• Do not plug the UPS into itself; this will damage the UPS and void your warranty.

• If connecting the UPS to a motor-powered AC generator, the generator must provide ﬁltered,

frequency-regulated output.

• To remove the UPS from the supply mains, the plug serves as a disconnect device.

• Once connected, do not limit access to the input plug. The plug must be accessible to be used as

a means of disconnection.

• When connecting the UPS to a power outlet, ensure the power outlet is provided with suitable

overcurrent protection in accordance with national and local electrical codes. Ensure the

overcurrent protection has a minimum of 1500A breaking capacity.

CAUTION: Do not remove cover for 5 minutes after disconnecting all sources of

supply. Risk of electric shock—hazardous live parts inside. Do not remove cover.

No user serviceable parts inside. Refer servicing to qualiﬁed service personnel.

This UPS receives power from more DC sources; disconnection of the AC and DC

source is required to de-energize the unit before servicing.

CAUTION: To ensure proper grounding with supply mains power, the input cord must

be connected with an approved country-speciﬁc plug with a protective earth ground

connection.

CAUTION: If this product is operated on battery (not connected to mains power),

adequate safeguards should be employed to protect against accidental contact

with AC power conductors.

CAUTION: Do not exceed total rated output.

WARNING: No modiﬁcation of this equipment is allowed.

18-06-068-933608.indb 3 6/22/2018 4:56:25 PM

Important Safety Instructions

Equipment Connection Warnings

• Do not use Tripp Lite UPS Systems for life support applications in which a malfunction or failure of

a Tripp Lite UPS System could cause failure or signiﬁcantly alter the performance of a life-support

device.

• The AC output is ﬂoating (the neutral output conductor is not grounded).

• Do not connect surge protectors or extension cords to the UPS output; doing so may damage the

UPS and affect the surge protector and UPS warranties.

CAUTION: The unit is for exclusive interconnection with IEC 60601-1 certiﬁed

equipment in the patient environment and IEC 60950-1 certiﬁed equipment outside

of the patient environment. Do not contact SIP/SOP (such as the USB port, RS-232

port, etc.) and the patient at the same time.

Battery Warnings

• Batteries can present a risk of electrical shock and burn from high short-circuit current. Observe

proper precautions. Do not dispose of the batteries in a ﬁre. Do not open the UPS or batteries.

Do not short or bridge the battery terminals with any object. Unplug and turn off the UPS before

performing battery replacement. Use tools with insulated handles. There are no user-serviceable

parts inside the UPS. Battery replacement should be performed only by authorized service

personnel using the same number and type of batteries (lithium iron phosphate). The batteries

are recyclable. At the end of the UPS unit’s life, follow best practice by discharging the battery

prior to disposal. Refer to local codes for disposal requirements. Tripp Lite offers a complete

line of UPS System Replacement Battery Cartridges (R.B.C.). Visit Tripp Lite on the Web at

www.tripplite.com/products/battery-ﬁnder/ to locate the speciﬁc UPS replacement battery.

• Do not operate UPS without batteries.

CAUTION: The unit is intended for use with Lithium Iron Phosphate batteries

provided by Tripp Lite. DO NOT mix with Sealed Lead Acid batteries. External

battery packs are not supported with this model. DO NOT attempt to add external

batteries.

UPS and Battery Recycling

Please recycle Tripp Lite Products. The batteries used in Tripp Lite products are lithium

iron phosphate batteries. These batteries are highly recyclable. Please refer to local codes

for disposal requirements.

Call Tripp Lite for recycling info at 1.773.869.1234.

Visit Tripp Lite’s Website for up-to-date information on recycling the batteries or any

Tripp Lite product. Please follow this link:

http://www.tripplite.com/support/recycling-program/

Replacement Battery

MODEL BATTERY AND QUANTITY NOMINAL VOLTAGE

OF BATTERY STRING PART NUMBER

SMART700HGL Lithium Iron Phosphate 12V / 3 pcs. 39.6V, 5Ah RBC51L / 3 pcs.

SMART1200XLHGL Lithium Iron Phosphate 12V / 3 pcs. 39.6V, 5Ah RBC51L / 3 pcs.

18-06-068-933608.indb 4 6/22/2018 4:56:25 PM

Important Safety Instructions

Package Contents

Maintenance:

• Other than battery replacement, the UPS does not require maintenance. There are no user

serviceable parts inside. Battery replacement should only be performed by qualiﬁed service

personnel.

Cleaning/Disinfecting:

• Before cleaning or disinfecting, the UPS should be turned off and unplugged.

• For cleaning the UPS, only a damp cloth should be used.

• For disinfecting the UPS, a damp cloth wetted with isopropyl alcohol may be used. No other

cleaning agent should be used.

UPS and Battery Disposal

• Always comply with local ordinances for proper methods of recycling and disposal of electronic

equipment.

• When purchasing a new UPS from Tripp Lite, you may send an old UPS back for recycling on a

one-for-one, like-for-like basis. The new equipment should also be sent back to Tripp Lite when it

ultimately becomes waste.

• Batteries can present risk of electric shock, burn and ﬁre if not disposed of properly.

SMART700HGL

• C13 to NEMA 5-15P-HG Power Cord, 6 ft.

• IEC Cord Lock

• USB A/B Cable, 6 ft.

• DB9 Cable, 6 ft.

• Owner’s Manual

SMART1200XLHGL

• C13 to NEMA 5-15P-HG Power Cord, 6 ft.

• IEC Cord Lock

• USB A/B Cable, 6 ft.

• DB9 Cable, 6 ft.

• Owner’s Manual

18-06-068-933608.indb 5 6/22/2018 4:56:25 PM

1Remove the two screws on

the battery door.

2Remove the battery door.

Connecting the Batteries

5 6

The UPS is shipped with the battery disconnected. The battery must be connected for the UPS to

operate. Connect the batteries to the UPS prior to connecting the UPS to AC mains, or connecting

any equipment to the UPS.

The installation procedure is as follows:

3Slightly slide the battery

pack out.

4Remove insulation on the

negative (-) battery terminal.

5Connect the negative (-)

battery terminal to the black

battery wire.

6Apply the insulation tape to

negative (-) battery terminal.

7Slide the battery pack back

into the UPS.

8Re-install the battery door

removed in step 2.

9Reinstall the two screws

removed in step 1.

18-06-068-933608.indb 6 6/22/2018 4:56:29 PM

Quick Installation

1Plug the UPS into a 3-wire grounded,

120V AC, 60 Hz utility outlet.

Note: UL 60601-1 listed UPS systems only meet UL standard UL

60601-1 for medical equipment when plugged into a hospital-grade

outlet.

Note: UPS system will function properly upon initial startup; however,

maximum runtime for the unit’s battery will only be accessible after it

has been charged for 24 hours.

After plugging the UPS into a live AC outlet, the UPS will

automatically charge its batteries but will not supply power

to its outlets until it is turned ON (see Step 3 below). The

BATTERY CHARGE LED will be the only LED illuminated.

2Plug equipment into the UPS.

The UPS will overload if the total VA ratings for all of connected

equipment exceeds the UPS Output Capacity. To ﬁnd an equipment’s

VA rating, look on its nameplates. If the equipment is listed in amps,

multiply the number of amps by 120 to determine VA (Example:

1 amp x 120 = 120VA). If unsure the UPS outlets are overloaded,

see “OUTPUT LOAD LEVEL” LED description.

3Turn the UPS ON.

Press and hold the “POWER” button for one second. The

alarm will beep once brieﬂy after one second has passed.

Release the button.

The UPS batteries must be fully charged (minimum 24 hours) before plugging

equipment into the UPS.

18-06-068-933608.indb 7 6/22/2018 4:56:29 PM

Quick Installation Optional

These connections are optional. Your UPS will function properly without these connections.

1Serial Communications

You can connect the UPS system’s DB9 port to the DB9 port

of a computer with the included cable. Use with

Tripp Lite’s PowerAlert Software for automatic ﬁle saves

and safe shutdown in case of power failure. (See Basic

Operation section.)

2USB Communications

Connect the USB port of your UPS to the USB port of a

computer with the included cable. Use with Tripp Lite’s

PowerAlert Software for automatic ﬁle saves and safe

shutdown in case of power failure. (See Basic Operation

section.)

18-06-068-933608.indb 8 6/22/2018 4:56:29 PM

Basic Operation

Buttons

“POWER” Button:

• To turn the UPS ON: With the UPS plugged into a live AC wall outlet,* press

and hold the POWER button for about two seconds.** Release the button. If

utility power is absent, the UPS can receive a “cold-start” (i.e.: turn it ON and

supply power for a limited time from its batteries***) by pressing and holding

the POWER button for about two seconds.**

• To turn the UPS OFF: With the UPS ON and receiving utility power, press and

hold the POWER button for one second.** Then unplug the UPS from the wall

outlet. The UPS will be completely OFF.

*After plugging the UPS into a live AC outlet, the UPS will automatically charge its batteries,

but will not supply power to its outlets until it is turned ON. ** The alarm will beep once

brieﬂy after the indicated interval has passed. *** If fully charged.

“MUTE/TEST” Button:

To Re-enable Audible Alarms: The UPS ships with the audible alarms muted by

default. To re-enable the audible alarms, press and hold the MUTE/TEST button

until a short beep sounds, followed by a continuous beep; then release the button.

To disable the audible alarms, press and hold the MUTE/TEST button until a short

beep followed by another short beep sounds; then release the button.

To Silence (or “Mute”) UPS Alarms: Brieﬂy press and release the MUTE/TEST

button.*

To Run a Self-Test: With the UPS plugged in and turned ON, press and hold the

MUTE/TEST button for two seconds.* The alarm will beep several times and the

UPS will perform a self-test. See “Results of a Self-Test” below.

Note: Equipment can remain powered on during a self-test. However, the UPS will not

perform a self-test if it is not turned ON (see “POWER” Button description).

CAUTION! Do not unplug the UPS to test its batteries. This will remove

safe electrical grounding and may introduce a damaging surge into your

network connections.

Results of a Self-Test: The test will last approximately 10 seconds as the

UPS switches to battery to test its load capacity and battery charge.** If the

“OUTPUT LOAD LEVEL” LED remains lit red and the alarm continues to sound

after the test, the UPS outlets are overloaded. To clear the overload, unplug

some equipment and run the self-test repeatedly until the “OUTPUT LOAD

LEVEL” LED is no longer lit red and the alarm is no longer sounding.

CAUTION! Any overload not corrected by the user immediately following

a self-test may cause the UPS to shut down and cease supplying output

power in the event of a blackout or severe brownout.

If the “BATTERY WARNING” LED remains lit and the alarm continues to sound

after the test, the UPS batteries need to be recharged or replaced. Allow

the UPS to recharge continuously for 12 hours, and repeat the self-test. If

the LED remains lit, contact Tripp Lite for service. If the UPS requires battery

replacement, visit www.tripplite.com/products/battery-ﬁnder/ to locate the UPS

system’s appropriate Tripp Lite replacement battery.

*The alarm will beep once brieﬂy after the indicated interval has passed. **Operation

during the self-test: the “POWER” LED will be ﬂashing and the “OUTPUT LOAD LEVEL” and

“BATTERY CHARGE” LEDs will be lit and the UPS alarm will sound.

18-06-068-933608.indb 9 6/22/2018 4:56:30 PM

Basic Operation

Indicator Lights

All Indicator Light descriptions apply when the UPS is plugged into an AC outlet and turned on.

“POWER” LED

This green LED illuminates continuously when the UPS is ON and supplying

connected equipment with AC power from a utility source. The LED ﬂashes

and an alarm sounds (4 short beeps followed by a pause) to indicate the UPS

is operating from its internal batteries during a blackout or severe brownout.

If the blackout or severe brownout is prolonged, save all ﬁles and shut down

equipment, as the internal battery power will eventually be depleted. See

“BATTERY CHARGE” LED description below.

“VOLTAGE CORRECTION” LED

This green LED illuminates continuously whenever the UPS is automatically

correcting high or low AC voltage on the utility line without the assistance of

battery power. The UPS will also emit a slight clicking noise. These are normal,

automatic operations of the UPS. No action is required.

“OUTPUT LOAD LEVEL” LED

This multicolored LED indicates the approximate electrical load of equipment

connected to the UPS AC outlets. It will turn from green (light load) to yellow

(medium load) to red (overload). If the LED is red (either illuminated continuously

or ﬂashing), clear the overload immediately by unplugging some equipment from

the outlets until the LED changes from red to yellow (or green) and the alarm

is no longer sounding. CAUTION! Any overload not corrected by the user

immediately may cause the UPS to shut down and cease supplying output

power in the event of a blackout or severe brownout.

“BATTERY CHARGE / BATTERY POWER” LED

When the UPS is operating from utility power, this multicolored LED indicates the

approximate charge state of the UPS system’s internal batteries: red indicates

the batteries are beginning to charge; yellow indicates the batteries are roughly

midway through charging; and green indicates the batteries are fully charged.

When the UPS is operating from battery power during a blackout or severe

brownout, this LED indicates the approximate amount of energy (ultimately

affecting runtime) the UPS batteries will provide: red indicates a low level of

energy; yellow indicates a medium level of energy; and green indicates a high

level of energy. Since the runtime performance of all UPS batteries will gradually

deplete over time, it is recommended to periodically perform a self-test (see

“MUTE/TEST” Button description) to determine the energy level of your UPS

batteries BEFORE a blackout or severe brownout occurs. During a prolonged

blackout or severe brownout, save all ﬁles and shut down equipment, as battery

power will eventually be depleted. When the LED turns red and an alarm sounds

continuously, it indicates the UPS batteries are nearly out of power and shut down

is imminent.

“BATTERY WARNING” LED

This LED illuminates red and an alarm sounds intermittently after initiating a

self-test (see “MUTE/TEST” Button description) to indicate the UPS batteries

need to be recharged or replaced. Allow the UPS to recharge continuously for

12 hours, and repeat the self-test. If the LED continues to light, contact

Tripp Lite for service. If the UPS requires battery replacement, visit

www.tripplite.com/products/battery-ﬁnder/ to locate the UPS system’s

appropriate Tripp Lite replacement battery.

18-06-068-933608.indb 10 6/22/2018 4:56:30 PM

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Tripp Lite UPS

Tripp Lite

Tripp Lite BCPERS450 Manuel utilisateur

Tripp Lite

Tripp Lite BCPRO1400 Manuel utilisateur

Tripp Lite

Tripp Lite Keyspan TuneView BC Pro Manuel utilisateur

Tripp Lite

Tripp Lite INTERNET550U Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline SU2200XL Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline SU20KX Manuel utilisateur

Tripp Lite

Tripp Lite OMNI750ISO Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro SMART5000RT3U Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro Series Manuel utilisateur

Tripp Lite

Tripp Lite AVR700U Guide de configuration

Tripp Lite

Tripp Lite SMART1500CRMXL Manuel utilisateur

Tripp Lite

Tripp Lite ECO UPS System Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline Single-Phase 10kVA Manuel utilisateur

Tripp Lite

Tripp Lite INTERNET550U Manuel utilisateur

Tripp Lite

Tripp Lite Audio/Video Pure Sine Wave UPS System Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline SU80K Manuel utilisateur

Tripp Lite

Tripp Lite UPS System AVRX550U Manuel utilisateur

Tripp Lite

Tripp Lite Power Suppy Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline SUINT1500LCD1U Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline SU1000XL Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline 5KVA Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro SLT Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro SMART1400RM2U Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro SLT SMX750SLT Guide de configuration

Manuels UPS populaires d'autres marques

Pylontech

Pylontech Victron & Pylontech US5000 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur

Mecer

Mecer ME-1000-WTU Manuel utilisateur

Mustek

Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation

Emerson

Emerson Liebert NXL series Manuel utilisateur

MAKELSAN

MAKELSAN BOXER SERIES Manuel utilisateur

Block

Block PC-0524-400-0 Manuel utilisateur

CyberPower

CyberPower CP585LCD Manuel utilisateur

Eaton

Eaton 3S Instructions de montage

CyberPower

CyberPower Office Tower Series UPS 1000 Manuel utilisateur

CyberPower

CyberPower BM100 Manuel utilisateur

Best Power

Best Power 610 Manuel utilisateur

Best Power

Best Power Unity/I UT3K Manuel utilisateur

Mustek

Mustek PowerMust 400 Offline Manuel utilisateur

Xantrex

Xantrex Trace 512 UR-UPS Manuel utilisateur

Forza

Forza SL-1501UL Manuel utilisateur

LEGRAND

LEGRAND keor 310081 Manuel utilisateur

ABB

ABB Conceptpower DPA 500 Manuel utilisateur