Transition Networks SM24TBT2DPA Manuel utilisateur

Transition Networks SM24TBT2DPA Quick Start Guide

33736 Rev. A https://www.transition.com Page 1of 2

SM24TBT2DPA

Managed Switch, 24-port Gigabit PoE++, 2-port

SFP/RJ-45 Combo

Quick Start Guide

Transition Networks’ SM24TBT2DPA Switch is a next-generation Ethernet switch offering full L2 features, full PoE

functionality, advanced L3 features, PoE++ per port output up to 90W. The Non-Stop PoE feature lets you upgrade

switch firmware or reboot while retaining PoE power to PDs.Note: see the Install Guide for important Safety

Warnings and Cautions, specifications, features, mounting, connections, grounding, powering, configuration,

troubleshooting, regulatory, service, warranty and tech support Information.

LED Descriptions

The front panel LEDs provide switch status checking and monitoring.

SYS (System) LED: indicates if the switch is powered up correctly or if there is a system alarm triggered.

Mode LEDs: indicate the mode of all RJ45/SFP ports on the switch. You can press the Mode/Reset button

sequentially to switch between the two different modes (Link/Activity/Speed mode and PoE mode).

Port Status LEDs: indicate the current status of each RJ45/SFP port. You can check these LEDs for port status in

different modes after changing the mode by pressing the Mode/Reset button.

Press the Mode/Reset button for less than 2 seconds to change LED mode (Link/Act/Speed Mode or PoE Mode);

you can then check the port status by reading the LED behaviors per the Install Guide.

Mode/Reset Button

Press the front panel Mode/Reset Button for a period of time to: Change Port Status LED Mode:

to read the port status correctly in the two different modes (Link/Act/Speed mode or PoE mode).

Reset the Switch: to reboot and get the switch back to the previous configuration settings saved.

The Non-Stop PoE feature lets you reboot the switch without losing PoE port power to the PDs.

Restore the Switch to Factory Defaults: to restore the original factory default settings back to the

switch. Note: See the Install Guide for LED behaviors.

Back Panel

The back panel provides for dual hot-swappable 1560W power supplies for powering the switch. The switch ships

with one power supply (780 Watts) standard; use a secondary power supply module (1560 Watts) if the full 90

Watts output is needed on all ports.

Package Contents

Check the package contents to make sure you have received the one Switch with a Power Supply installed, one

AC Power cord,asecond Power Supply (Optional), one RJ-45 to DB-9 cable, and four rubber feet.

Install SFP Modules

Do not look into laser ports. 1. Position the SFP at either install slot with the SFP label facing

correctly. 2. Carefully slide the SFP device into the slot, aligning it with the internal installation

guides. 3. Press firmly so the SFP firmly seats against the internal mating connector. 4. Attach

an appropriate cable into the SFP module port. 5. Attach the other end of the cable into the other device.

Transition Networks SM24TBT2DPA Quick Start Guide

33736 Rev. A https://www.transition.com Page 2of 2

Grounding

ATTENTION: This case must be grounded. No DC input may be earth grounded. Use Isolated

Power Supply. Note: The switch is an indoor device. If it used with outdoor devices such as

outdoor IP cameras or outdoor WiFi APs, then you should install a surge protector or surge

suppressor in order to protect the switch.

Connecting to Power

CAUTION! Hazardous Area: Do Not remove this cover. Trained service people only. No serviceable components

inside. CAUTION: Hot Surfaces. WARNING: For continued protection against risk of fire, replace only with same

type and rating of fuse. Note the sticker indicating “To Keep Warranty Please Do NOT Remove”.

Connect the AC Power Cord

Warning: Risk of electrical shock. For multiple power sources: Energy hazard if both power modules are not

disconnected. Disconnect both power sources before servicing. Warning: Shock/damage hazard exists if power

supply is installed / removed while powered on.

1. Refer to the “Grounding” section above. 2. Remove the blank faceplate or use the

one open power supply slot. 3. Fasten the AC Power Supply with the slotted

retaining screw. 4. Insert the provided AC Power plug into the switch AC receptacle

(power inlet). 5. Connect the other end of the AC power cord to the AC power outlet.

6. Check that the AC OK and DC OK LEDs are lit.

Initial Switch Config via Web Browser

Power up the switch and perform the initial switch config using a web browser.

1. Connect the PC Ethernet RJ45 connector to the switch via standard Ethernet LAN cable. 2. Power up the PC to

be used for initial config. 3. Reconfigure the PC’s IP address and Subnet Mask so it can communicate with the

switch. 4. Power up the switch to be initially configured, and wait until it has finished its start-up processes.

5. Connect the PC to any port on the switch using a standard Ethernet cable; make sure the switch port LED is lit.

6. In a Web browser, enter the switch default IP address (192.168.1.77) and Subnet Mask (255.255.255.0). The

page. 8. Click the “Login” button to log into the switch. See the Web User Guide for more information.

Initial Switch Config via CLI

1. Use an RJ-45 cable to connect a terminal or PC/terminal emulator to the switch port to access the CLI.

2. Attach the RJ-45 serial port on the switch front panel to the cable for Telnet/CLI configuration. 3. Attach the

other end of the DB-9 cable to a PC running Telnet or a terminal emulation program such as HyperTerminal or

TeraTerm. 4. After powering up the switch for the first time, you can perform the initial switch configuration

using the CLI (Command Line Interface). See the CLI Reference for managing other switch features.

Transition Networks | 10900 Red Circle Drive | Minnetonka, MN 55343 USA | tel: +1.952.941.7600 | toll free:

1.800.526.9267 | fax: 952.941.2322 | web: https://www.transition.com

Autres manuels pour SM24TBT2DPA

Table des matières

Autres manuels Transition Networks Changer

Transition Networks

Transition Networks SM24-100SFP-AH Manuel utilisateur

Transition Networks

Transition Networks SISGM1040-284-LRT Manuel utilisateur

Transition Networks

Transition Networks SM24-100SFP-AH Manuel utilisateur

Transition Networks

Transition Networks SISTP1040-382B-LRT Manuel utilisateur

Transition Networks

Transition Networks LANMaster T8-FL Manuel utilisateur

Transition Networks

Transition Networks SM24DPB Manuel utilisateur

Transition Networks

Transition Networks mil-sm8dpa Manuel

Transition Networks

Transition Networks SISPM1040-582-LRT Manuel utilisateur

Transition Networks

Transition Networks MIL-S2400S Manuel utilisateur

Transition Networks

Transition Networks 1005 Manuel utilisateur

Transition Networks

Transition Networks SISPM1040-582-LRT Manuel utilisateur

Transition Networks

Transition Networks SM Series Manuel utilisateur

Transition Networks

Transition Networks SESPM1040-541-LT Series Manuel utilisateur

Transition Networks

Transition Networks SM8TAT2SA Mode d’emploi

Transition Networks

Transition Networks SESPM1040-541-LT Series Manuel utilisateur

Transition Networks

Transition Networks Milan MIL-SM2401MAF Manuel utilisateur

Transition Networks

Transition Networks SISPM1040-384-LRT-C Manuel utilisateur

Transition Networks

Transition Networks SM TAT4X Series Manuel utilisateur

Transition Networks

Transition Networks SM24DPa Manuel utilisateur

Transition Networks

Transition Networks E-FL-HB-0400 Manuel utilisateur

Transition Networks

Transition Networks SM24TBT2DPA Manuel utilisateur

Transition Networks

Transition Networks STACKMASTER TX12 Manuel utilisateur

Transition Networks

Transition Networks SM8TAT2SA-DC Manuel utilisateur

Transition Networks

Transition Networks SISTP1040-342-LRT Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur