Transition Networks E-MUX-SA05 Manuel utilisateur
Jabber: Flashing or lit LED indicates jabber on the line
Collision: Occasional or on LED indicates line collisions
Power: Lit LED indicates normal operation
FCC Regulations:
NOTE: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harm-
ful interference when the equipment is operated in a commercial envi-
ronment. This equipment generates, uses, and can radiate radio fre-
quency energy and, if not used in accordance with the instruction manu-
al, may cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful interfer-
ence in which case the user will be required to correct the interference
at his own cost.
NOTE: This digital apparatus does not exceed the Class A limits for
radio noise for digital apparatus set out on the radio interference regula-
tions of the Canadian Department of Communications.
Trademarks:
ST is a registered trademark of AT&T.
Ethernet is a registered trademark of Xerox Corporation, Inc.
Technical Support:
For more information about this product or other TRANSITION
Networks products, call you local Transition distributor. Or contact us
by phone at (612) 941-7600 or fax at (612) 941-2322.
P/N 7320.A
ETHERNET MULTIMEDIA
QUAD AUI FAN OUT
E-MUX-SA05
About the Multimedia Quad Fan Out:
The TRANSITION Networks Quad AUI Fan Out allows the user to inter-
connect up to four workstations, hubs or fanouts together (five with the
optional slide in card feature). The externally powered AUI Fan Out has
four standard AUI (DB-15 male) connections and an expansion slot for
installing an additional interface. The SIC’s, or slide in cards which are
installed in the expansion slot, can be purchased with either an AUI,
thin coax, 10BaseT or fiber-optic interface. This solution allows the user
added flexibility when installing an Ethernet network, while also reduc-
ing the number of transceivers required.
Power
Collision
Receive
Transmit
Jabber
Transmit
Jabber
Transmit
Jabber
Transmit
Jabber
E N G I N E E R I N G , I N C .
TRANSITION
Ethernet
Multimedia
Quad Fan Out
E-MUX-SA05
Switch setting
Switch Settings
Loopback + No SQE 2
Loopback + SQE 1
No Loopback + No SQE 3
Port 1 Port 2
Port 3 Port 4
Coax, 10BaseT, or Fiber Optional Slide In Card (SIC)
External Power Connection
Jabber: Flashing or lit LED indicates jabber on the line
Collision: Occasional or on LED indicates line collisions
Power: Lit LED indicates normal operation
FCC Regulations:
NOTE: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harm-
ful interference when the equipment is operated in a commercial envi-
ronment. This equipment generates, uses, and can radiate radio fre-
quency energy and, if not used in accordance with the instruction manu-
al, may cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful interfer-
ence in which case the user will be required to correct the interference
at his own cost
ETHERNET MULTIMEDIA
QUAD AUI FAN OUT
E-MUX-SA05
About the Multimedia Quad Fan Out:
The TRANSITION Networks Quad AUI Fan Out allows the user to inter-
connect up to four workstations, hubs or fanouts together (five with the
optional slide in card feature). The externally powered AUI Fan Out has
four standard AUI (DB-15 male) connections and an expansion slot for
installing an additional interface. The SIC’s, or slide in cards which are
installed in the expansion slot, can be purchased with either an AUI,
thin coax 10BaseT or fiber optic interface This solution allows the user
Features of the Quad Fan Out:
* External Configuration Switch
* Optional Slide In Cards for AUI, Coax, Twisted Pair and Fiber-optic
interfaces
* Easy to read LED indicators: Transmit, Receive, Jabber, Collision
and Power
* A two year warranty
* Made in the U.S.A
* UL listed, FCC class A compliant
External Switch Settings:
1) Loopback and SQE: Setting 1 when enabled is used for connecting
workstations using the AUI ports, (No optional slide in card can be
installed).
2) Loopback and No SQE: Setting 2 when enabled is used for connect-
ing hubs or repeaters using the AUI ports, (No optional slide in card can
be installed).
3) No Loopback and No SQE: Setting 3 when enabled for Optional
slide in card. Loopback provided by slide in card, the SQE enabled /
disabled is selectable on the card (switch located on the top of the card).
Using the Quad Fan Out:
The Quad AUI Fan Out can be used to connect 4 workstations, hubs or
fan outs together. This provides a cost effective solution that reduces the
number of transceivers and allows greater flexibility in your network
with the optional slide in interface cards. The Quad Fan Out is not a
repeater and will not extend the distance between segments. The Quad
Fan Out must be used with IEEE approved AUI cables.
Optional Slide in cards:
* Fiber-optic interface, P/N E-FRL-SIC
* Coax interface, P/N E-CX-SIC
* Twisted Pair interface, P/N E-TBT-SIC
The Quad Fan Out Specifications:
Enclosure size: 6.25 inches X 5 inches X 1.3 inches
AUI Connections: IEEE 802 Ethernet cable, 50 meters max
Optional Coax interface: RG-58 - 50 ohm coaxial cable
(610 feet maximum distance)
Optional Twisted Pair interface: Level 4, 2 pair twisted, 330 feet
maximum
Optional Fiber-optic interface: ST connectors, 6,600 maximum distance
Environment: 0-70° C, 5% - 90% humidity non-condensing, 0-10,000
foot altitude
Warranty: 2 year limited warranty
Monitoring The Quad Fan Out LED’s:
Transmit (TX): Flashing or lit LED indicates a packet has been
transmitted
Receive (RX): Flashing or lit LED indicated a packet has been received
Features of the Quad Fan Out:
* External Configuration Switch
* Optional Slide In Cards for AUI, Coax, Twisted Pair and Fiber-optic
interfaces
* Easy to read LED indicators: Transmit, Receive, Jabber, Collision
and Power
* A two year warranty
* Made in the U.S.A
* UL listed, FCC class A compliant
External Switch Settings:
repeater and will not extend the distance between segments. The Quad
Fan Out must be used with IEEE approved AUI cables.
Optional Slide in cards:
* Fiber-optic interface, P/N E-FRL-SIC
* Coax interface, P/N E-CX-SIC
* Twisted Pair interface, P/N E-TBT-SIC
The Quad Fan Out Specifications:
Enclosure size: 6.25 inches X 5 inches X 1.3 inches
AUI Connections: IEEE 802 Ethernet cable, 50 meters max
Autres manuels Transition Networks Changer
Transition Networks
Transition Networks SM Series Manuel utilisateur
Transition Networks
Transition Networks SISPM1040-384-LRT-C Manuel utilisateur
Transition Networks
Transition Networks SM8TAT2SA Mode d’emploi
Transition Networks
Transition Networks E-TBT-HB-1600 Manuel utilisateur
Transition Networks
Transition Networks MIL-L100i Manuel utilisateur
Transition Networks
Transition Networks SISPM1040-582-LRT Manuel utilisateur
Transition Networks
Transition Networks SISGM-CHAS L2 Manuel utilisateur
Transition Networks
Transition Networks MIL-S4800 Manuel utilisateur
Transition Networks
Transition Networks SISPM1040-3248-L Instructions d'utilisation et d'entretien
Transition Networks
Transition Networks SISPM1040-582-LRT Manuel utilisateur
Transition Networks
Transition Networks SISPM1040-3-L Series Manuel utilisateur
Transition Networks
Transition Networks LANMaster T8-FL Manuel utilisateur
Transition Networks
Transition Networks SM24-100SFP-AH Manuel utilisateur
Transition Networks
Transition Networks SM24DP4XA Manuel utilisateur
Transition Networks
Transition Networks SISTM1040-262D-LRT Manuel utilisateur
Transition Networks
Transition Networks SM16TAT2SA Manuel utilisateur
Transition Networks
Transition Networks SISPM1040-3 L Series Manuel utilisateur
Transition Networks
Transition Networks SISGM1040-284-LRT Manuel utilisateur
Transition Networks
Transition Networks MIL-SEM24T4GPA Manuel utilisateur
Transition Networks
Transition Networks SM24DP4XA Manuel utilisateur
