Transition Networks E-FX-HB-0800 Manuel utilisateur

Minneapolis, MN 55344 USA

100BASE-FX Fast Ethernet™

Unmanaged Fiber Hub with TX or FX Uplink

E-FX-HB-1600, E-FX-HB-0800

USER’S GUIDE

The stackable, rack-mountable E-FX-HB-1600 and E-FX-HB-0800 series

unmanaged Fast Ethernet™fiber hubs allow the network administrator to

set up and to modify workgroups connected over fiber and to install an

optional copper or fiber backbone uplink connection to the workgroups

and/or optional connections for stacking up to five hubs.

E-FX-HB-1600, E-FX-HB-1600(SC)

The E-FX-HB-1600 hub provides sixteen (16) Fast Ethernet™ST OR SC

fiber connections to terminal devices plus space for an optional copper or

fiber backbone uplink and space for an optional stacking adapter.

E-FX-HB-0800, E-FX-HB-0800(SC)

The E-FX-HB-0800 hub provides eight (8) Fast Ethernet™ST OR SC fiber

connections to terminal devices plus space for an optional copper or fiber

backbone uplink and space for an optional stacking adapter.

BACKBONE UPLINK ADAPTERS Optional devices ordered separately that, when

installed, provide one of the following Fast Ethernet™backbone uplink connections:

MA-FST •ST connector to multimode fiber

MA-FSC •SC connector to multimode fiber

MA-FSM • SC connector to singlemode fiber

MA-TX •RJ-45 connector to twisted-pair copper, AutoCross™feature

STACKING ADAPTERS Optional

devices ordered separately that, when

installed, allow stacking between E-FX-

HB-xx00 hubs.

ACC-0200 •Stacking adapter

ACC-0201 •Stacking cable

E-FX-HB-xx00 in the Network . . . . .2

Installation . . . . . . . . . . . . . . . . . . . .4

Operation . . . . . . . . . . . . . . . . . . . .11

Fault Isolation and Correction . . . .12

Cable Specifications . . . . . . . . . . . .14

Technical Specifications . . . . . . . . .15

Compliance Information . . . . . . . . .16

STAT

PWR

COL

ACT

100BASE-FX

12345678

910 11 12 13 14 15 16

ACT

STAT

GFT

2457

911

10 12 13 15

14 16

STAT

PWR

COL

100BASE-FX

12345678

ACT

GFT

2457

COMPLIANCE INFORMATION

UL Listed

C-UL Listed (Canada)

CISPR/EN55022 Class A

FCC Regulations

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant

to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference, in which case the user will be

required to correct the interference at the user’s own expense.

Canadian Regulations

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on

the radio interference regulations of the Canadian Department of Communications.

Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables

aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique

édictépar le ministère des Communications du Canada.

European Regulations

Warning

This is a Class A product. In a domestic environment this product may cause radio interference in which

case the user may be required to take adequate measures.

Achtung !

Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses Gerätes

Rundfunkstörungen auftreten, in weichen Fällen der Benutzer für entsprechende Gegenmaßnahmen

werantwortlich ist.

Attention !

Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des

interférences radioélectriques, il appartiendra alors àl’utilsateur de prende les measures spécifiques

appropriées

VCCI Class 1 Compliance

This equipment is in the 1st Class category (information equipment to be used in commercial and/or

industrial areas) and conforms to the standards set by the Voluntary Control Council For Interference by

Data Processing Equipment and Electronic Office Machines aimed at preventing radio interference in

commercial and/or industrial areas. When used in a residential area or in an adjacent area thereto,

interference may be caused to radio and TV receivers, etc. Read the instructions for correct handling.

Trademark Notice

All registered trademarks and trademarks are the property of their respective owners.

graphic, electronic, or mechanical –without written permission from TRANSITION Networks.

Printed in the U.S.A. 33122.A

CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE

PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in

damage to the public telephone network.

Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-Mitgliedstaaten

verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91/263/EWG zur

Angleichung der Rechtsvorschriften der Mitgliedstaaten über Telekommunikationsendeinrichtungen

einschliesslich der gegenseitigen Anerkennung ihrer Konformität.

E-FX-HB-xx00 IN THE NETWORK

Install one E-FX-HB-xx00

hub and use fiber cable

to set up a workgroup by

connecting the hub to

terminal devices.

Install an optional

backbone uplink adaptor at

the back of the hub and use

copper or fiber cable to

connect the workgroup to a

network backbone.

Install an optional expansion

adaptor at the back of up to

five (5) hubs and then use

expansion adaptor cables to

connect the hubs into a

stack that functions as one

Class A repeater.

TECHNICAL SPECIFICATIONS

Standards IEEE 802.3

Dimensions 17.25" x 8.5" x 1.7" (437 mm x 216 mm x 43 mm)

Power

Input Range: 100 to 240 VAC at 50 or 60 Hz, 3.0 A maximum.

Rated at 40 watts maximum.

Environment Operating Temperature: 0°to 50°C (32°to 122°F )

Storage Temperature: -15°to 65°C (5°to 149°F )

Humidity 5% to 95%, non condensing

Altitude 0 to 10,000 feet

Warranty Lifetime

DECLARATION OF CONFORMITY

Name of Mfg: Transition Networks

6475 City West Parkway, Minneapolis MN 55344 USA

Model: E-FX-HB-xx00 Series Unmanaged Fiber Hub

Part Number: E-FX-HB-1600, E-FX-HB-1600(SC), E-FX-HB-0800,

E-FX-HB-0800(SC)

Regulation: EMC Directive 89/336/EEC

Purpose: To declare that the E-FX-HB-1600 or E-FX-HB-0800 to which this

declaration refers is in conformity with the following standards.

EMC-CISPR 22: 1985 Class A; EN 55022: 1988 Class A; EN 50082-1:1992;

EN 60950 A4:1997; IEC 801.2, IEC 801.3, and IEC 801.4; IEC 950

I, the undersigned, hereby declare that the equipment specified above conforms to the

above Directive(s) and Standard(s).

_November 10, 1999_____

Stephen Anderson, Vice-President of Engineering Date

STAT

PWR

457

911

10 12 13 15

14 16

COL

ACT

100BASE-FX

12345678

910 11 12 13 14 15 16

ACT

STAT

GFT

STAT

PWR

457

911

10 12 13 15

14 16

COL

ACT

100BASE-FX

12345678

910 11 12 13 14 15 16

ACT

STAT

GFT

to hub, switch, or router

STAT

PWR

457

911

10 12 13 15

14 16

COL

ACT

100BASE-FX

12345678

910 11 12 13 14 15 16

ACT

STAT

GFT

STAT

PWR

457

911

10 12 13 15

14 16

COL

ACT

100BASE-FX

12345678

910 11 12 13 14 15 16

ACT

STAT

GFT

STAT

PWR

457

911

10 12 13 15

14 16

COL

ACT

100BASE-FX

12345678

910 11 12 13 14 15 16

ACT

STAT

GFT

STAT

PWR

457

911

10 12 13 15

14 16

COL

ACT

100BASE-FX

12345678

910 11 12 13 14 15 16

ACT

STAT

GFT

STAT

PWR

457

911

10 12 13 15

14 16

COL

ACT

100BASE-FX

12345678

910 11 12 13 14 15 16

ACT

STAT

GFT

CABLE SPECIFICATIONS

Twisted Pair Cable and Connector Specifications

MA-TX Category 5 twisted-pair copper

Either shielded twisted-pair (STP) or unshielded twisted-pair (UTP) can be used. .

CATEGORY 5:

Gauge 24 to 22 AWG

Attenuation 22.0 dB /100m @ 100 MHz

Maximum Cable Distance*: 100 meters

Twisted pair connection requires two active pairs configured as straight-through

OR as crossover. The two active pairs in an Ethernet™network are pins 1 & 2

and pins 3 & 6. Use only dedicated wire pairs (such as blue/white & white/blue,

orange/white & white/orange) for the active pins.

Fiber Cable

MULTIMODE

Fiber Optic Cable Recommended: 62.5 / 125 µm multimode fiber

Optional: 100 / 140 µm multimode fiber

85 / 125 µm multimode fiber

50 / 125 µm multimode fiber

Bit error rate: ≤10-11

E-FX-HB-xx00, MA-FST 1300 nM

Fiber-optic Transmitter Power: min: -16.0 dBm max: -9.0 dBm

Fiber-optic Receiver Sensitivity: min: -35.0 dBm max: -14.0 dBm

Link Budget 19 dB

Typical Maximum Cable Distance:* 2 kilometers

E-FX-HB-xx00(SC), MA-FSC 1300 nM

Fiber-optic Transmitter Power: min: -16.0 dBm max: -9.0 dBm

Fiber-optic Receiver Sensitivity: min: -35.0 dBm max: -14.0 dBm

Link Budget 19 dB

Typical Maximum Cable Distance:* 2 kilometers

SINGLEMODE

Fiber Optic Cable Recommended: 9 µm singlemode fiber

Bit error rate: ≤10-11

MA-FSM 1300 nM

Fiber-optic Transmitter Power: min: -16.0 dBm max: -9.0 dBm

Fiber-optic Receiver Sensitivity: min: -35.0 dBm max: -14.0 dBm

Link Budget 19 dB

Typical Maximum Cable Distance:* 20 kilometers

*Actual distance dependent upon physical characteristics of network installation.

Using the 512-Bit Rule

When configuring Fast Ethernet™networks, use the 512-bit rule to determine

masimum cable lengths for each half-duplex collision domair.

In a half-duplex network, maximum

cable lengths are determined by the

round trip delay limitations of each Fast

Ethernet™collision domain. (Switches

and routers divide the network into

separate Ethernet™collision domains.)

The 512-Bit Rule determines maximum

distances by calculating the collision

domain round-trip delay in bit-times.

To calculate a collision domain

round-trip delay in bit-times, find

the longest path between any two

terminal devices in the collision

domain. Calculate the round trip

delay by multiplying the length of

the cable (in meters) by the delay

per meter (in bit-times (BT)), then

take the sum of all cable delays

plus station (DTE), repeater, and

multi-port media converter port

delays. If the result is less than or

equal to 512 bit-times, the path is

good.

to hub, switch or router

STAT

PWR

457

911

10 12 13 15

14 16

COL

ACT

100BASE-FX

12345678

910 11 12 13 14 15 16

ACT

STAT

GFT

STAT

PWR

457

911

10 12 13 15

14 16

COL

ACT

100BASE-FX

12345678

910 11 12 13 14 15 16

ACT

STAT

GFT

STAT

PWR

457

911

10 12 13 15

14 16

COL

ACT

100BASE-FX

12345678

910 11 12 13 14 15 16

ACT

STAT

GFT

STAT

PWR

457

911

10 12 13 15

14 16

COL

ACT

100BASE-FX

12345678

910 11 12 13 14 15 16

ACT

STAT

GFT

STAT

PWR

457

911

10 12 13 15

14 16

COL

ACT

100BASE-FX

12345678

910 11 12 13 14 15 16

ACT

STAT

GFT

STAT

PWR

457

911

10 12 13 15

14 16

COL

ACT

100BASE-FX

12345678

910 11 12 13 14 15 16

ACT

STAT

GFT

STAT

PWR

457

911

10 12 13 15

14 16

COL

ACT

100BASE-FX

12345678

910 11 12 13 14 15 16

ACT

STAT

GFT

STAT

PWR

457

911

10 12 13 15

14 16

COL

ACT

100BASE-FX

12345678

910 11 12 13 14 15 16

ACT

STAT

GFT

Collision Domain

Class II

Hub

30 meters TP

@ 1.11BT/meter

= 33.3BT

5 meters TP

@ 1.11BT/meter

= 5.55BT

= 140BT

Class I

Hub

= 140BT

20 meters TP

@ 1.11BT/meter

= 22.2BT

DTE=50BT

50.00BT

+22.20BT

+140.00BT

+5.55BT

+140.00BT

+33.30BT

+50.00BT

___________

= 441.05BT

Switch

= 50BT

Class I repeater 140 BT

Class II repeater 92 BT

Class I TX/FX media converter 130 BT

Class II TX/FX media converter 92 BT

DTE (PC, switch, router) 50 BT

1 meter CAT.5 TP cable 1.11 BT

1 meter fiber cable 1 BT

Fast Ethernet switch 50 BT

Cascade two repeater stacks by

connecting fiber cable from a

connector at the front of the

first hub to a connector at the

front of the second hub.

Crossover

Straight Through

Twisted Pair #1 Twisted Pair #1

Twisted Pair #2

INSTALLATION

Optionally Install Expansion Adapter

WARNING: Remove AC line cord from power source before installing

expansion adaptor in E-FX-HB-xx00. Failure to observe this warning could

result in personal injury or death.

CAUTION: Wear a grounding device and observe electrostatic discharge

precautions when installing Expansion Adapter in the E-FX-HB-xx00. Failure

to observe this caution could result in damage to, and subsequent failure of,

Expansion Adapter.

To install the expansion adapter in the E-FX-HB-xx00:

1. Locate expansion adapter plate at back of E-FX-HB-xx00.

2. Remove expansion adapter plate by using flatblade screwdriver to

remove two (2) screws that secure expansion adapter plate to back

of E-FX-HB-xx00.

NOTE: Retain screws for step 5. (Optionally discard expansion

adapter plate.)

3. Carefully slide expansion adapter, component side up, into

installation space revealed by removal of expansion adapter plate.

CAUTION: Do NOT force the connection. Failure to observe this

caution could result in equipment damage and subsequent failure.

4. Press component on expansion adapter securely against internal

mating E-FX-HB-xx00 component until expansion adapter faceplate

is flat against E-FX-HB-xx00 chassis.

5. Secure expansion adapter by installing retained screws through

expansion adapter into E-FX-HB-xx00 chassis.

YES

•Continue at step 7.

7. Is one (or more) of the 100BASE-FX STAT(us) LEDs illuminated

continuously?

YES

•Continue at step 10

•Continue at step 8.

8. Does one (or more) of the 100BASE-FX STAT(us) LEDs blink on

and off?

YES

•Check fiber cables for proper connection.

•Verify that TX and RX cables on E-FX-HB-xx00 are connected to RX

and TX ports, respectively, on terminal device. (See page 9.)

•Ensure that terminal device(s) is/are powered.

•Contact Technical Support: (800) 260-1312.

•Continue at step 9.

9. Is one (or more) of the 100BASE-FX STAT(us) LEDs dark?

YES

•The port is (or ports are) partitioned; investigate the attached

terminal device(s).

•Contact Technical Support: (800) 260-1312.

•Continue at step 10.

10. Is one (or more) of the 100BASE-FX ACT(ivity) LEDs

illuminated?

YES

•The port is (or ports are) operational and receiving data.

•Disconnect and reconnect the 100BASE-FX cable to restart the

initialization process.

•Restart the terminal device(s) to restart the initialization process.

•Contact Technical Support: (800) 260-1312.

Expansion Adapter Plate

FAULT ISOLATION and CORRECTION

If the E-FX-HB-xx00 fails, isolate and correct the fault by determining the

answers to the following questions and then taking the indicated action:

1. Is the P(o)W(e)R LED on the E-FX-HB-xx00 illuminated?

•Is the power cord properly installed in the E-FX-HB-xx00 and in the

grounded AC outlet?

•Does the grounded AC outlet provide power?

•Contact Technical Support: (800) 260-1312.

YES

•Continue at step 2.

2. Is a backbone uplink adapter installed at E-FX-HB-xx00 back?

•Continue at step 7.

YES

•Continue at step 3.

3. Is the B(ack)B(one) STAT(us) LED illuminated continuously?

YES

•Continue at step 7.

•Continue at step 4.

4. Does the B(ack)B(one) STAT(us) LED blink on and off?

YES

•Ensure that backbone uplink adapter is firmly connected.

•Check backbone uplink cables for proper cabling and connection(s).

•Ensure that device at remote end of network link is powered.

•Contact Technical Support: (800) 260-1312.

•Continue at step 5.

5. Is the B(ack)B(one) STAT(us) LED dark?

YES

•The port is partitioned or isolated; investigate the device at the far

end of the link.

•Contact Technical Support: (800) 260-1312.

•Continue at step 6.

6. Is the B(ack)B(one) ACT(ivity) LED illuminated?

•Disconnect and reconnect the backbone cable to restart the

initialization process.

•Restart the attached network device to restart the initialization

process.

•Contact Technical Support: (800) 260-1312.

Optionally Install Backbone Uplink Adapter

WARNING: Remove AC line cord from power source before installing

backbone uplink adaptor in E-FX-HB-xx00. Failure to observe this warning

could result in personal injury or death.

CAUTION: Wear a grounding device and observe electrostatic discharge

precautions when installing backbone uplink adaptor in the E-FX-HB-xx00.

Failure to observe this caution could result in damage to, and subsequent

failure of, backbone uplink adaptor.

To install the backbone uplink adapter in the E-FX-HB-xx00:

1. Locate backbone uplink adapter plate at back of E-FX-HB-xx00.

2. Remove backbone uplink adapter plate by using flatblade

screwdriver to remove two (2) screws that secure backbone uplink

adapter plate to back of E-FX-HB-xx00.

NOTE: Retain screws for step 5. (Optionally discard backbone

uplink adapter plate.)

3. Carefully slide backbone uplink adapter, component side up, into

installation space revealed by removal of backbone uplink adapter

plate.

CAUTION: Do NOT force connection. Failure to observe this caution

could result in equipment damage and subsequent failure.

4. Press component on backbone uplink adapter securely against

internal mating E-FX-HB-xx00 component until backbone uplink

adapter faceplate is flat against E-FX-HB-xx00 back.

5. Secure backbone uplink adapter by installing retained screws

through backbone uplink adapter into E-FX-HB-xx00 chassis back.

Backbone Uplink Adapter Plate

Install E-FX-HB-xx00 at Site

WARNING: During the site installation, handle the E-FX-HB-xx00 in such a

way that the E-FX-HB-xx00 does not fall. Failure to observe this warning

could result in injury to personnel and/or equipment damage.

NOTE: If E-FX-HB-xx00 is shipped with brackets installed, proceed to step 2.

To install the E-FX-HB-xx00 in 19-inch rack cabinet:

1. Remove and retain two (2) screws located at front left side and front

right side of E-FX-HB-xx00 chassis. Install right and left front

brackets (provided) on chassis by installing two (2) retained screws

through each bracket into chassis.

2. Carefully align E-FX-HB-xx00 between 19-inch rack mounting rails.

3. Install E-FX-HB-xx00 by installing two (2) screws through right front

bracket into rack and two (2) screws through left front bracket into

rack, using clip nuts (NOT provided) to secure, if necessary.

To install the E-FX-HB-xx00 on table or other flat surface:

NOTE: Rubber feet are provided.

1. Carefully turn E-FX-HB-xx00 to side.

2. Install four (4) rubber feet:

•Separate rubber feet.

•Remove protective paper

from adhesive

surface on rubber

foot.

•Position and

secure each

rubber foot as

shown.

3. Return E-FX-HB-xx00 to upright position.

OPERATION

Use the status LEDs to monitor E-FX-HB-xx00 operation in the network.

HUB INDICATORS

P(o)W(e)R Steady LED indicates E-FX-HB-xx00 is

connected to external AC power.

COL(lision) Flashing LED indicates network collisions.

G(lobal) F(ault) S(tatus) Steady LED indicates the presence of a

partitioned or isolated port. (A port is

partitioned automatically after a collision

occurs during 60 or more consecutive

attempts to transmit to the port; a port is

isolated if more then two consecutive false

carrier events are received.)

NOTE: The hub unpartitions/unisolates the

port when network traffic becomes normal.

The GFS LED remains illuminated until the

partition/isolation condition is corrected.)

B(ack)B(one) & 100BASE-FX INDICATORS

STAT(us) Steady LED indicates, for each port, a valid

link and no partition or isolation.

Dark LED indicates, for each port, that port

is not linked, is isolated, or is partitioned.

ACT(ivity) Flashing LED indicates, for each port,

reception of data packet(s).

STAT

PWR

COL

ACT

100BASE-FX

12345678

910 11 12 13 14 15 16

ACT

STAT

GFT

STAT

PWR

457

911

10 12 13 15

14 16

COL

ACT

100BASE-FX

12345678

910 11 12 13 14 15 16

ACT

STAT

GFT

Power the E-FX-HB-xx00

NOTE: When the hub is connected to an AC outlet supplying 100-240VAC at

50-60 Hz, the hub automatically powers ON

To power ON the E-FX-HB-xx00:

1. Locate power receptacle at back of E-FX-HB-xx00.

2. Plug unit end (female) of power cord into E-FX-HB-xx00 power

receptacle.

3. Plug outlet end (male) of power cord into correct voltage AC wall

socket.

4. At E-FX-HB-xx00 front, verify that P(o)W(e)R LED is illuminated.

Optionally Cascade Hubs

AT BACK

To cascade hubs by installing adapter cable(s) between stacked hubs:

1. Locate uplink adapter installed on E-FX-HB-xx00 9see page 4) and

adapter cable ACC-0201.

2. Install one end of adapter cable to UPPER connector on expansion

adapter on lowest hub in stack.

3. Install one end of adapter cable to LOWER connector on expansion

adapter on next hub in stack.

4. Continue steps 2-3 until installation is complete.

AT FRONT

To cascade hubs by installing fiber cables between hubs:

1. Locate or build 100BASE-FX compliant two-stranded fiber cable

with appropriate TX to RX connectors installed at both ends.

2. Connect male TX and RX cable connectors at one end of cable to

TX and RX female connectors, respectively, on front of one hub.

3. Connect male TX and RX cable connectors at other end of cable to

RX and TX connectors, respectively, on front of second hub.

STAT

10BASE-FL

12345678

PWR

COL ACT

2457

STAT

10BASE-FL

12345678

PWR

COL ACT

2457

TX RX

Optionally Connect to Backplane through TX Uplink

NOTE: Refer to 512-bit rule (page 3) to keep cable lengths within acceptable

bounds.

To connect twisted-pair cable from E-FX-HB-xx00 100BASE-TX uplink

adapter to network:

1. Locate 100BASE-TX uplink adapter installed at E-FX-HB-xx00 back.

(See page 5.)

NOTE: AutoCross™feature on 100BASE-TX uplink adapter allows

use of either straight-through or crossover 100BASE-TX cable

configuration.

2. Locate or build 100BASE-TX compliant cables with male RJ-45 plug

connectors at both ends. (See page 14.)

3. Connect male RJ-45 plug connector at one end of cable to

E-FX-HB-xx00 100BASE-TX uplink adapter RJ-45 jack connector.

4. Connect male RJ-45 plug connector at other end of cable to RJ-45

jack connector on 100BASE-TX network device.

Optionally Connect to Backplane through FX Uplink

NOTE: Refer to 512-bit rule (page 3) to keep cable lengths within acceptable

bounds.

To connect fiber cable from E-FX-HB-xx00 100BASE-FX uplink adapter to

network:

1. Locate 100BASE-FX uplink adapter installed at E-FX-HB-xx00 back.

(See page 5.)

2. Locate or build 100BASE-FX compliant fiber cable with male two-

stranded TX to RX connectors at both ends. (See page 14.)

3. Connect male TX and RX cable connectors at one end of cable to

TX and RX female connectors, respectively, on E-FX-HB-xx00

100BASE-FX uplink adapter.

4. Connect male TX and RX cable connectors at other end of cable to

RX and TX connectors, respectively, on 802.3 compliant

100BASE-FX network device.

Connect Hub to Terminal Devices using Fiber

NOTE: Refer to 512-bit rule (page 3) to keep cable lengths within acceptable

bounds.

To connect fiber cable from E-FX-HB-xx00 ports to terminal devices:

1. Locate or build 100BASE-FX compliant two-stranded fiber cable

with appropriate male TX to RX connectors installed at both ends.

2. Connect male TX and RX cable connectors at one end of cable to

TX and RX female connectors, respectively, on E-FX-HB-xx00 port.

3. Connect male TX and RX cable connectors at other end of cable to

RX and TX connectors, respectively, on 802.3 compliant fiber

device.

4. Repeat steps 1-3 until all terminal devices are connected.

TX RX

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Transition Networks Changer

Transition Networks

Transition Networks SISPM1040-582-LRT Manuel utilisateur

Transition Networks

Transition Networks SM12DP2XA Manuel utilisateur

Transition Networks

Transition Networks SISGM1040-284-LRT Manuel utilisateur

Transition Networks

Transition Networks SM24-100SFP-AH Manuel utilisateur

Transition Networks

Transition Networks SISPM1040-3-L Series Manuel utilisateur

Transition Networks

Transition Networks SM TAT4X Series Manuel utilisateur

Transition Networks

Transition Networks SM24TBT2DPA Manuel utilisateur

Transition Networks

Transition Networks SISPM1040-362-LRT Manuel utilisateur

Transition Networks

Transition Networks LANMaster T8 Manuel utilisateur

Transition Networks

Transition Networks STACKMASTER TX12 Manuel utilisateur

Transition Networks

Transition Networks SISPM1040-582-LRT Manuel utilisateur

Transition Networks

Transition Networks LANMaster T8-FL Manuel utilisateur

Transition Networks

Transition Networks SISTP10xx-141-LR(T) Manuel utilisateur

Transition Networks

Transition Networks SISPM1040-3 L Series Manuel utilisateur

Transition Networks

Transition Networks MIL-S800I-V2 Manuel utilisateur

Transition Networks

Transition Networks SM8TAT2SA-DC Manuel utilisateur

Transition Networks

Transition Networks SM24T6DPA Manuel utilisateur

Transition Networks

Transition Networks SISTG1040-242-LRT Manuel utilisateur

Transition Networks

Transition Networks Milan MIL-SM2401MAF Manuel utilisateur

Transition Networks

Transition Networks E-TBT-HB-0402 Manuel utilisateur

Transition Networks

Transition Networks SISTG1040-242-LRT Manuel utilisateur

Transition Networks

Transition Networks ETHERNET POCKET HUB 401 Manuel utilisateur

Transition Networks

Transition Networks E-TBT-HB-1002 Manuel utilisateur

Transition Networks

Transition Networks SESPM1040-541-LT Series Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur