TRAK 3ntr Series Manuel utilisateur
TRAK®3ntr 3D Printers
Printer Electrical Connection Quick Start Guide
Covers Current Models:
•3ntr A2
•3ntr A4
2615 Homestead Place
Rancho Dominguez, CA 90220-5610 USA
T | 310.608.4422 |F | 310.764.2668
Service Department: 800.367.3165
e-mail: sales@trakmt.com | service@trakmt.com | web: www.trakmt.com
Document: P/N 32235
Version: 111919
Copyright ©2019, Southwestern Industries, Inc. All rights are reserved. No part of this publication may
be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, mechanical,
photocopying, recording or otherwise, without the prior written permission of Southwestern Industries,
Inc.
While every effort has been made to include all the information required for the purposes of this guide,
Southwestern Industries, Inc. assumes no responsibility for inaccuracies or omission and accepts no
liability for damages resulting from the use of the information contained in this guide.
All brand names and products are trademarks or registered trademarks of their respective holders.
Southwestern Industries, Inc.
2615 Homestead Place
Rancho Dominguez, CA 90220
Phone 310-608-4422 Fax 310-764-2668
Service Department
Phone 800-367-3165 Fax 310-886-8029
1
TRAK Machine Tools
Southwestern Industries, Inc.
TRAK 3ntr 3D Printers –Printer Electrical Connection Quick Start Guide
1Electrical Connections
In this section, you will make the electrical connection to the printer and MMS unit (if applicable)
CAUTION –Employ a licensed electrician to help with electrical connection and wiring where these
instructions are unclear, or your site installation specifics are different.
A2 printers are all configured for 220V US Power. A4 printers are typically configured for 110V US power;
however, may be optionally configured for 220 V US power. If you have an A4 printer - refer to your
order paperwork and/or contact the dealer to determine the actual power configuration for your A4
printer before proceeding.
1.1 Verify Input Power Source Voltage/Phase
3ntr printers configured for 220V (All A2 and some A4 Printers) are powered with a single phase 230V
and a ground connection. The neutral line is not used. Verify socket wiring with a multi-meter before
connecting printer/MMS unit or wiring printer cable.
Figure 8.1 Printer surface plate re-installed in printer
2
TRAK Machine Tools
Southwestern Industries, Inc.
TRAK 3ntr 3D Printers –Printer Electrical Connection Quick Start Guide
1.2 MMS Unit 220V Electrical Power Connection
NOTE: This section only applies if an MMS unit is to be used with the printer.
The MMS units connects to a 220VAC Single phase connection. In this case, the printer should also be
configured for 220VAC Single phase power. The printer connects to the outlet on the top of the MMS
unit. The power cable supplied with the MMS terminates in bare wires so that a plug compatible with
your facility can be installed.
1) Obtain standard 220 VAC Single phase power cable OR wire supplied MMS cable following
instructions in section below: “Wiring a Printer or MMS Power Cable for 220V Single Phase”
Figure 8.2.1 Typical 3ntr A2 Printer or MMS Power Cable
2) Plug power cable into MMS Unit
3
TRAK Machine Tools
Southwestern Industries, Inc.
TRAK 3ntr 3D Printers –Printer Electrical Connection Quick Start Guide
Figure 8.2.2 MMS Unit Power Plug and Switch
3) Plug cable into external power receptacle:
Figure 8.2.3 220 VAC Single Phase Plug and Receptacle
4
TRAK Machine Tools
Southwestern Industries, Inc.
TRAK 3ntr 3D Printers –Printer Electrical Connection Quick Start Guide
1.3 Standard 3ntr 220V Electrical Power Connections
1) Inspect power connection locations on printer/MMS units and supplied cables to ensure the
connectors are matching and cables are for the correct voltage/phase as the printer.
2) Plug power cable into Printer
Figure 8.3.1 Printer Power Connection
Figure 8.3.2 Printer Power Plug
3) If there is no MMS unit, plug Printer cable into appropriate wall outlet (220VAC 15A Single Phase)
4) If there is an MMS unit, plug the Printer power cable into the power outlet on the MMS Unit
5
TRAK Machine Tools
Southwestern Industries, Inc.
TRAK 3ntr 3D Printers –Printer Electrical Connection Quick Start Guide
Figure 8.3.3 Printer power outlet on MMS Unit
1.4 Wiring a Printer or MMS Power Cable for 220V Single Phase
NOTE –In most cases, re-wiring a power cable is not required. If your printer was designed for 220VAC
power and was shipped with a standard 110 VAC cable, you will need to either A) contact your dealer
and obtain the correct power cable (Preferred) or B) Have a qualified electrician wire one for your 220
VAC power source. The supplied cable is rated for the appropriate current in either case.
1) Wire Cable plug for 220VAC Single Phase as shown.
CAUTION –The neutral line is not used. Connecting it as if it were ground will damage other systems
connected to the printer
6
TRAK Machine Tools
Southwestern Industries, Inc.
TRAK 3ntr 3D Printers –Printer Electrical Connection Quick Start Guide
Figure 8.4 220 VAC Power Plug Wiring.
Green = Ground. Black and White = 230 VAC single phase
2) Verify cable wiring with a multi-meter before connecting to printer/power. Measure between the
printer power cable ground and any 110VAC wall socket ground. This should be zero “0” volts.
If there is a potential present, it is likely a neutral line has been used where a ground wire should
have been.
CAUTION –Do not connect the printer or any peripherals until the ground/neutral line has been
sorted out and there is no potential between printer ground and the 110V ground.
1.5 3ntr A4 printer with 120 VAC US Power Connection
Plug in the printer cord to a normal 120 VAC 15A US outlet as with any appliance.
Autres manuels pour 3ntr Series
7
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels TRAK Imprimante 3D
TRAK
TRAK Airwolf EVO-T Manuel de programmation
TRAK
TRAK 3ntr Series Manuel utilisateur
TRAK
TRAK 3ntr Series Manuel utilisateur
TRAK
TRAK 3ntr Series Manuel utilisateur
TRAK
TRAK Airwolf 3D EVO-T Mode d'emploi
TRAK
TRAK 3ntr Series Manuel utilisateur
TRAK
TRAK 3ntr Series Manuel utilisateur
TRAK
TRAK 3ntr A2 Manuel de programmation
TRAK
TRAK 3ntr Series Manuel de programmation
TRAK
TRAK 3ntr Series Manuel
