Torrey LSQ-40L Manuel d'instructions

LSQ-40L

LABEL PRINTING SCALE

QUICK START

MANUAL

REV 1.0

PAGE 1

INDEX

Before you begin……………………………………………………………2

Cleaning the scale

Requirements for using a computer to program

Setting up scale for first use………………………………………………..4

Testing printer

Printing your first label……………………………………………………..5

Setting up the network……………………………………………………..6

Connecting the devices

Installing the software

Configuring you computer

Configuring your scale(s)…………………………………………………..7

Starting up the software……………………………………………………8

Adding scales to the network

Configuring general information…………………………………………..9

Adding products…………………………………………………………..10

Moving products to/from scale……………………………………………11

Access Direct

General configuration……………………………………………………..12

Bar code setup

Printed text on labels……………………………………………………...13

Headlines

Passwords

Programming using the keyboards…………………………………………14

Entering store information

Edit scrolling message………………………………………………….…15

Configuration……………………………………………………………….16

Setting up label print………………………………………………………17

Setting up bar code

Placing text on label……………………………………………………….18

Set up text on label……………………………………………………...…19

Add plu’s…………………………………………………………………..20

Key assignation

Troubleshooting……………………………………………………………22

Page 2

BEFORE YOU BEGIN

Please read this section carefully. The following has some important safeguards to

prevent damage or failure of your scale.

CLEANING THE SCALE:

1). You may use stainless cleaner or mild soap to wipe down the metal areas of the

scale. The keyboards and display should be wiped down with a damp cloth only.

While the keyboards and display are reasonably sealed, do not allow liquids to get

between the plastic surfaces and the metal.

2). Use only the supplied cleaning kit to clean the print head. Do not use sharp

objects around the print head or the pinch roller below it. Damaging these parts will

cause your label printouts to be unreadable or you may even cause internal damage

to the scale.

3). Do not immerse the power supply in water. This will cause possible electrical

shock and failure of the adapter. Unplug adapter from power and wipe down with a

damp cloth. Do not spray the adapter with cleaning fluids.

4). Keep the print cartridge area clean of any food or other debris. If contaminants

are picked up by the labels and brought across the print head, it can cause labels to

print poorly. This can also damage the print head.

COMMUNICATIONS WITH THE SCALE:

If you are going to program your scale using a personal computer, here are a few

things you will need.

1). You will need to purchase a network adapter (hub) and two (2) category 5 cables.

These can be purchased from electronics or department stores that sell computer

equipment. A network adapter allows you to plug your computer and scale(s) into

one hub. NOTE: You cannot plug the scale directly into your computer. Being your

scale is actually a computer, all computers that communicate with each other

require a network adapter to control data flow between machines.

Page 3

Network Adapter with category 5 cables

The picture above shows an example of a 5 port hub. One computer and up to 4

scales can be connected for programming.

NOTE: It is not necessary to have a computer to program your scale. Programming

can be done by using the keyboard on the scale. However, it is much easier to

program using a computer especially if you have more than one scale.

A few other advantages of using a computer are:

1). Information can be saved to your hard drive or other backup device.

2). You can communicate to the scales from a remote location such as a back office.

You would not have to go to the machine or move it to program/update.

3). You can generate reports from the scale and print them without interrupting

normal operations of the day.

Page 4

SETTING UP THE SCALE FOR FIRST TIME

1). Carefully unpack scale from it’s box. Lift the indicators arm all the way up until

it stops. Adjust the correct angle of the indicator by loosening the black nut on the

arm next to the indicator. Move the indicator to the correct angle and then tighten

the nut. DO NOT over tighten.

2). Plug in the ac adapter to the wall socket and the other end into the scale. The

connector may appear tight on a new scale. You might try twisting the connector as

you are pushing it into the scales receptacle.

3). Turn on the scale. It should do a regressive countdown, then a label should

dispense. If the scale does not turn on, try twisting the connector again while

leaving the switch in the on position.

QUICK TEST OF THE PRINTER:

1). Remove the template from the main keyboard. There is a tab on the left side so it

can be pulled out. This exposes the programming keyboard.

2). Find the key(s) that came with the scale. Insert the key into the lock on the

bottom right of the scale. Turn it right 90 degrees.

3). The indicator should display PWD? Press the PRINT key. The scrolling message

should say PROGRAMMING MODE.

4). On the programming keyboard, press CONFIG. Using the arrow down button,

scroll down until it says MODE.

5). Press ENTER. The indicator should say AGENTS. Press ENTER.

6). Arrow up/dn until you see DISABLE. Press ENTER.

7). Arrow down until you see NON PLU. Press ENTER.

8). Arrow up/dn until you see ENABLE. Press ENTER.

9). Press ESC on the small keyboard until the scrolling message says

PROGRAMMING MODE again. Turn the key to the left and remove it.

Page 5

TO PRINT A LABEL (contd):

1). Place a product on the platter. Enter in the price. Press PRINT.

A label should dispense with printed information such as weight, date, total sale,

etc.

NOTE: The printer will not print a label if no price is entered, no weight is on the

platter or negative weight is displayed on the indicator. Repeat steps on page 5 if no

label comes out.

**CONGRADULATIONS!!** You have just printed your first label.

Page 6

SETTING UP THE NETWORK

(Skip this part if not using a computer)

____________________________

1). Connect up the equipment as shown in the drawing below.

2). Place the Scalenet (LSQ-40L) software CD in your drive. The auto install should

begin automatically. Complete the installation as instructed.

NOTE: This software is intended to run on a Windows XP operating system with

SP2 (Service Pack 2) installed only.

CONFIGURING YOUR NETWORK ON YOUR COMPUTER:

1). Click on START, then NETWORK CONNECTIONS.

2). Click on LOCAL AREA NETWORK.

3). Click on PROPERTIES.

4). Scroll down on window and click ONCE on INTERNET PROTOCAL TCP/IP.

5). Click on PROPERTIES.

6). Click on MANUALLY ENTER IP ADDRESS.

7). Enter in the IP address 131.1.100.100. Click OK.

Page 7

NOTE: If you are already using a network connection for another application, you

may want to create a new connection and configure it for scale communications.

CONFIGURING YOUR NETWORK ON THE SCALE:

The scales network IP address should already be configured from the factory. If

you want to check it or if you are using more than one scale, follow the procedure

below.

TO SEE/CHANGE SCALES IP ADDRESS:

1). If the scale is on, turn it off.

2). Turn on the scale. During the countdown, press and release the following keys in

sequential order. Press TARE, X, +, and then AGENT before the countdown

completes.

NOTE: Scales with serial numbers starting with H08-xxxx or higher must press

TARE first then X, +, and then AGENT.

3). Display should go blank. Enter 2005 and press PRINT.

4). Press PRINT to scroll thru the address numbers. At any time you may change

them by entering the new numbers. The first scales address should be 131.1.100.101.

5). Press ESC when complete.

If you are using more than one scale on the network, then each scale must have its

own network address. EXAMPLE: SCALE#1 131.1.100.101

SCALE#2 131.1.100.102

SCALE#3 131.1.100.103

NOTE: You should write down each address. You will need to type it in again later

to add them to the network.

Page 8

STARTING UP THE LSQ-40L SOFTWARE

(Be sure your scale and hub are powered up and connected at this time)

1). Launch the LSQ-40L software. On the logon screen, do not enter a password.

Click on ACCEPT to continue.

2). At the top of the screen, click on MAINTENANCE and then SCALE MASTER.

Below is the screen you should be viewing at this point.

SCALE MASTER allows you to add new scales to the network. You will have to

add each scale to the network one at a time. As long as you use the same computer

each time you communicate to your network, you should not have to add them

again.

TO ADD A NEW SCALE TO THE NETWORK:

1). Click on NEW.

Page 9

2). Go to the first IP box and click in it. Enter the first number. Press TAB and enter

the second number. Repeat for the last two numbers.

3). Click on SEARCH FOR SCALES. If the network detects the scale, it will ask you

‘Do you want to add scale?’. Click YES.

4). The scales information should appear on the screen. If you have more than one

scale, repeat step 1.

NOTE: If you get a Enable message, the network did not find the scale. Either you

entered the wrong IP address, or the network is not configured correctly. If you

have more than one network configured, you may have to disable the other

networks.

CONFIGURE GENERAL PARAMETERS:

To set up for North America (USA) operations and currency, on the top of the

screen click on PARAMETER and then SYSTEM COFIGURATION.

1). Under the COMPANY INFORMATION tab, enter your stores information.

2). Under the SYSTEM DATA tab, enter the following information:

Current Symbol = $

Decimal Symbol = .

Decimal Number= 2

3). Click on SAVE the CLOSE.

Table des matières

Autres manuels Torrey Échelle

Torrey

Torrey CRS Series Manuel utilisateur

Torrey

Torrey PC HSP Series Manuel utilisateur

Torrey

Torrey FS 250/500 Manuel utilisateur

Torrey

Torrey QC Series Manuel utilisateur

Torrey

Torrey LPC HS Series Manuel utilisateur

Torrey

Torrey EQB-50/100 Manuel utilisateur

Torrey

Torrey WLS Manuel utilisateur

Torrey

Torrey W-LABEL Series Manuel utilisateur

Torrey

Torrey PC Series Manuel utilisateur

Torrey

Torrey W-LABEL 40L Manuel utilisateur

Torrey

Torrey LSQ Series Manuel du propriétaire

Torrey

Torrey PPC Series Manuel utilisateur

Torrey

Torrey L-EQ 5/10 Manuel utilisateur

Torrey

Torrey WLS SERIES Manuel utilisateur

Torrey

Torrey QC Series Manuel utilisateur

Torrey

Torrey LSQ Series Manuel utilisateur

Torrey

Torrey CRS-HD 200 Manuel utilisateur

Torrey

Torrey LSQ Series Manuel utilisateur

Torrey

Torrey L-EQ HS Series Manuel utilisateur

Torrey

Torrey EQB-W Series Manuel utilisateur

Torrey

Torrey PS Series Manuel utilisateur

Torrey

Torrey CRS Series Manuel utilisateur

Torrey

Torrey EQB Series Manuel utilisateur

Torrey

Torrey L-PC SERIES Manuel utilisateur

Manuels Échelle populaires d'autres marques

AWS

AWS ZEO-50 Manuel utilisateur

Gima

Gima Glass Body Fat Analyzer Manuel de la liste des pièces

Seca

Seca 374 Manuel utilisateur

TEC

TEC TEC SL59 SERIES Manuel utilisateur

Axis

Axis B/E Series Manuel utilisateur

Alecto

Alecto ACW-40 Manuel utilisateur

Rice Lake

Rice Lake MSI-4260 IS Manuel utilisateur

IKA

IKA RCT basic safety control Manuel utilisateur

ADE

ADE M20011 Manuel utilisateur

Duronic

Duronic KS3000 Manuel utilisateur

Digi

Digi SM-720 Manuel utilisateur

Cardinal

Cardinal CS Series Manuel utilisateur

Korona

Korona Kastella Manuel utilisateur

A&D

A&D FC-50Ki Manuel utilisateur

BDA

BDA CAMARGUE Manuel utilisateur

Tanita

Tanita HD-357 Manuel utilisateur

Leifheit

Leifheit 03173 Manuel utilisateur

Lumme

Lumme LU-1340 Manuel utilisateur