Tohnichi CTB Manuel utilisateur

CTB Retightening Torque Wrench

Quick Start

1) Charge CTB using Tohnichi AC Adapter # QC-1 for approx 1hr until green light goes

on.

2) Keep wrench stable, with no movement while you press On button

3) Wrench will go through a gyro sensor stabilizing function “—-” will appear followed

by “good”. If “Error0” appears then sensor did not stabilize properly. Turn unit Off

and On again until “good” is display.

4) Setup Auto reset and Data Output functions by pressing “C”, then “MEM”, then “MD”

keys in that order.

5) “Ar” will show in the corner .The“0.0” setting is for manual reset, which means you

must press “MEM” key after each reading is taken. Using arrow keys, change setting

to show seconds after peak torque is achieved to automatically store reading into mem-

ory. Press “MEM” to save setting and proceed to next selection.

6) “do” will appear in the corner. Using arrow keys select data output methods: PC (to

computer), PRN (to printer), or IFR (infrared Data Tank R-DT100-3) Press “MEM” to

save selection.

7) Counter indicates “00” This is run mode. Use arrow keys to select a count number to

move into peak mode.

8) On a bolt that has already been tightened, position wrench on fastener, pull steady and

smoothly until green light turns on and buzzer will sound. Stop pulling.

9) As you are pulling value will indicate peak torque followed by “P” on the end. Once

bolt head starts to move sensor gives green light ,

CTB Retightening Torque Wrench

Quick Start

10) Value will change to initial tightening torque value. The “P” will no longer

be at the end of the value and displayed value will be lower. This reading

should be very close to the original tightened torque.

11) If you do not pull until ,green light goes on , “E-1” error alarm will sound

and display will flash. You must clear the display and start again.

12) To access statistical, functions move counter to the highest count number

that data is stored press “MD” to see total number in sample (N)

13) Press “MD” a second time to see “Hi” value in sample

14) Press “MD” a third time to see “Lo”value in sample

15) Press “MD” a fourth time to see “—” average value of sample.

For long term storage, use jack plug to shut off battery to gyro sensor. This will

help keep battery from draining quickly. After jack is removed, allow wrench to

stabilize 20 minutes before use.

For further assistance, call 1-847-272-8480

Contact us for information regarding downloading data to Excel file.

Table des matières

Autres manuels Tohnichi Outils électriques

Tohnichi

Tohnichi PQL Manuel utilisateur

Tohnichi

Tohnichi DATA TORK CEM3-G-WF Manuel utilisateur

Tohnichi

Tohnichi MPQL Manuel utilisateur

Tohnichi

Tohnichi CSPFHW Manuel utilisateur

Tohnichi

Tohnichi DB SERIES Manuel utilisateur

Tohnichi

Tohnichi QL2N Manuel utilisateur

Tohnichi

Tohnichi TiQL Manuel utilisateur

Tohnichi

Tohnichi CTB10N2X8D-G Manuel utilisateur

Tohnichi

Tohnichi CLE2 Manuel utilisateur

Tohnichi

Tohnichi DATA TORK CEM3-G Manuel utilisateur

Tohnichi

Tohnichi QSPCA Series Manuel utilisateur

Tohnichi

Tohnichi CMQSP Manuel utilisateur

Tohnichi

Tohnichi QLLS Manuel utilisateur

Tohnichi

Tohnichi CTA2-G Manuel utilisateur

Tohnichi

Tohnichi CL2Nx8D-MH Manuel utilisateur

Tohnichi

Tohnichi FH256MC Manuel utilisateur

Tohnichi

Tohnichi WQL Series Manuel utilisateur

Tohnichi

Tohnichi QL Manuel utilisateur

Tohnichi

Tohnichi QRSP-SP2-N Series Manuel utilisateur

Tohnichi

Tohnichi YCL2 Manuel utilisateur

Tohnichi

Tohnichi PHL Manuel utilisateur

Tohnichi

Tohnichi CL2NX8D Manuel utilisateur

Tohnichi

Tohnichi SF Manuel utilisateur

Tohnichi

Tohnichi SP Series Manuel utilisateur

Manuels Outils électriques populaires d'autres marques

AEG

AEG OMNI-JS Manuel utilisateur

SIP

SIP 01533 Manuel utilisateur

Ribimex

Ribimex PRS499 Manuel utilisateur

3M

3M Fiber Optic Connector Crimp Tool Manuel utilisateur

Ryobi

Ryobi P524 Manuel utilisateur

ROJEK

ROJEK FSN 300A Manuel utilisateur

Kemper

Kemper 1740PRO Manuel utilisateur

WABCO

WABCO OptiTire Manuel utilisateur

EINHELL

EINHELL TE-MS 18/210 Li Manuel utilisateur

Orgapack

Orgapack OR-T 85 Guide rapide

TOUGHCUT

TOUGHCUT Diamond 400 Manuel utilisateur

Yaros

Yaros PB-3603 Manuel utilisateur

Fein

Fein BSS 2.0 E Guide de configuration

Baileigh Industrial

Baileigh Industrial SS-2725 Manuel utilisateur

Milwaukee

Milwaukee 2674-20 Manuel utilisateur

Fein

Fein BLs 1.6 Manuel utilisateur

Princess

Princess Electric Multi Sharpener Manuel utilisateur

FOREDOM

FOREDOM K.1050 Manuel