Texas Instruments TRF7970A BoosterPack Manuel utilisateur

SLOU452–December 2016

NFCLink Standalone Getting Started

Getting Started Guide

SLOU452–December 2016

NFCLink Standalone Getting Started

This guide assists users in the initial firmware setup and demonstration of Peer-to-Peer mode,

Reader/Writer mode, and Card Emulation mode of the TRF7970A BoosterPack™ plug-in module with an

MSP430F5529 LaunchPad™ development kit. The guide explains how to flash the example firmware that

is provided by TI. Additionally, it describes how to implement the different modes with the NFCLink

Standalone GUI.

www.ti.com

2SLOU452–December 2016

Submit Documentation Feedback

NFCLink Standalone Getting Started

Contents

1 Introduction ................................................................................................................... 3

2 Getting Started............................................................................................................... 3

3 TI NFC Tool GUI ........................................................................................................... 12

4 Summary .................................................................................................................... 22

List of Figures

1 UniFlash Installation......................................................................................................... 4

2 Selecting .out File in UniFlash ............................................................................................. 5

3 Code Composer Studio™ IDE Installation ............................................................................... 6

4 CCS Import Project Window ............................................................................................... 7

5 Device Manager With LaunchPad™ Development Kit Shown as an Other Device ................................ 8

6 Update Driver Software Using Device Manager......................................................................... 9

7 Browse Computer for Driver Software................................................................................... 10

8 Location Of CDC Driver in Installed Firmware Package.............................................................. 11

9 TI NFC Tool Auto Connect................................................................................................ 12

10 TI NFC Tool Manual Connect ............................................................................................ 12

11 Antenna Location on DLP-7970ABP..................................................................................... 13

12 Phone Correct and Incorrect Presentation to BoosterPack™ Plug-in Module..................................... 14

13 Tag Correct and Incorrect Presentation to BoosterPack™ Plug-in Module ........................................ 15

14 BoosterPack™ Plug-in Module Correct and Incorrect Presentation to BoosterPack™ Plug-in Module........ 15

15 NFC Configuration Tab – P2P Configuration........................................................................... 16

16 Peer-to-Peer Tab........................................................................................................... 17

17 NFC Configuration Tab – RW Configuration ........................................................................... 18

18 Reader/Writer Mode Tab.................................................................................................. 19

19 NFC Configuration Tab – CE Configuration ............................................................................ 20

20 Card Emulation Tab........................................................................................................ 21

21 Advanced COM Tab ....................................................................................................... 21

Trademarks

BoosterPack, LaunchPad, Code Composer Studio, MSP430 are trademarks of Texas Instruments.

All other trademarks are the property of their respective owners.

www.ti.com

Introduction

SLOU452–December 2016

NFCLink Standalone Getting Started

1 Introduction

This guide has two main objectives: It describes how to download the NFCLink Standalone example code

to an MSP-EXP430F5529LP, and it also describes how to use the TI NFC Tool GUI. The example code

and GUI can be downloaded from http://www.ti.com/lit/zip/sloa227. This guide describes how to install and

use two different flash programming options: Code Composer Studio™ IDE and UniFlash. The guide also

describes how to use the TI NFC Tool GUI to interact with NFC tags and NFC enabled devices.

1.1 Prerequisites

The user should have the following items:

• DLP-7970ABP

• MSP-EXP430F5529LP

• An NFC tag or NFC enabled device

• A computer running Microsoft® Windows® 7 or XP operating systems

2 Getting Started

This section describes the required software and hardware setup for the DLP-7970ABP BoosterPack plug-

in module and the MSP-EXP4305529LP LaunchPad development kit with the NFCLink Standalone

example firmware.

2.1 Download and Install Software

Download the NFCLink Standalone GUI and example code from http://www.ti.com/lit/zip/sloa227.

Install the software package following the default options.

2.2 Hardware Setup

Attach the DLP-7970ABP to the MSP-EXP430F5529LP so that pin 1 of the BoosterPack plug-in module is

aligned with the 3.3V pin of the LaunchPad development kit. Then connect the MSP-EXP430F5529LP to

the PC using the provided USB cable.

2.3 Flash the Firmware

The NFCLink Standalone firmware requires either UniFlash or Code Composer Studio IDE (CCS) v6.1.1

or newer to download code to the LaunchPad development kit. If you have only the CCS free license, use

UniFlash to download the example code. This is due to the maximum download capacity of CCS under

the free license.

Getting Started

www.ti.com

4SLOU452–December 2016

Submit Documentation Feedback

NFCLink Standalone Getting Started

2.3.1 Option 1: UniFlash

2.3.1.1 Download and Install

Download and run the UniFlash installation wizard (version 3.4 or newer) from

http://www.ti.com/tool/uniflash. Use the default settings until the Select Components selection (see

Figure 1). The default option is install all components, but the minimum requirement is only to install the

MSP430 Ultra Low Power component under Microcontrollers. Choose which components to install based

on preferred disk usage. The installation of additional debug probes is optional. Follow the remaining

installation instructions in the wizard to complete the installation process.

Figure 1. UniFlash Installation

www.ti.com

Getting Started

SLOU452–December 2016

NFCLink Standalone Getting Started

2.3.1.2 Import and Configure Project

To use Uniflash to flash the NFCLink Standalone firmware to the MSP-EXP430F5529LP:

1. Open UniFlash.

2. Go to File →New Configuration.

3. Connection →MSP430 USB1 and Board or Device →MSP430F5529. Click Ok.

4. When connected, click Program →Load Program.

5. Select Browse and find the configuration file at [Installed Path]\examples\boards\MSP-

EXP430F5529LP\F5529LP_TRF7970A_ALL_NFC_MODES\Debug and select the

F5529LP_TRF7970A_ALL_NFC_MODES.out file (see Figure 2).

6. Click OK. The firmware should automatically begin to load into flash memory on the MSP-

EXP4305529LP.

7. After the firmware is loaded, cycle the power to the LaunchPad development kit by unplugging the

USB cable and then plugging it back in.

Figure 2. Selecting .out File in UniFlash

Getting Started

www.ti.com

6SLOU452–December 2016

Submit Documentation Feedback

NFCLink Standalone Getting Started

2.3.2 Option 2: Code Composer Studio™ IDE (CCS)

2.3.2.1 Download and Install

Download and run the Code Composer Studio IDE version 6.1.1 or newer (CCS) installation wizard from

http://processors.wiki.ti.com/index.php/Download_CCS. Online and offline installation options are

available. If any issues occur with the online installer, then try the offiline installer instead. Use the default

installation options up until Processor Support (see Figure 3). The minimum requirement is to select only

MSP Ultra Low Power MCUs for processor support. Additional processor support can be added based on

preferred disk usage. Follow the remaining installation instructions in the wizard to complete the

installation process.

Figure 3. Code Composer Studio™ IDE Installation

2.3.2.2 Import and Configure Project

To use Code Composer Studio IDE version 6.1.1 to flash the NFCLink Standalone firmware to the MSP-

EXP430F5529LP, follow these steps:

1. Open Code Composer Studio IDE.

2. Go to Project →Import CCS Projects…

3. Click Browse and select the directory: [Installed Path]\examples\boards\MSP-

EXP430F5529LP\F5529LP_TRF7970A_ALL_NFC_MODES.

4. Import the F5529LP_TRF7970A_ALL_NFC_MODES project (see Figure 4).

5. Select the imported project in the Project Explorer window and then click the debug icon to build

the project and download the example firmware to the device.

6. Click the terminate button in the debugging window.

7. Cycle the power to the LaunchPad development kit by unplugging the USB cable and then plugging it

back in.

8. The firmware on the LaunchPad development kit now operates in stand-alone mode and reads

NFC/RFID tags by default.

www.ti.com

Getting Started

SLOU452–December 2016

NFCLink Standalone Getting Started

9. If the CDC driver for the LaunchPad development kit is installed on the host PC, then the LaunchPad

development kit is ready to connect to the TI NFC Tool GUI. See Section 2.4 for details on how to

determine if the CDC driver is installed.

Figure 4. CCS Import Project Window

Getting Started

www.ti.com

8SLOU452–December 2016

Submit Documentation Feedback

NFCLink Standalone Getting Started

2.4 Install the MSP430™ CDC Driver

To determine if the CDC driver for the MSP-EXP430F5529LP is installed, run Device Manager on the PC

after the firmware example has been flashed to the LaunchPad development kit. For Windows users, this

can be done by going to Control Panel →Device Manager →Other Devices.

It is mandatory that the firmware be flashed on the MSP-EXP430F5529LP first. This is because it is the

firmware example that attempts to enumerate the CDC port to the COM port list, and there is no way to

tell if the CDC driver is installed or not unless the firmware attempts that CDC port enumeration.

If the MSP430 LaunchPad development kit appears as an Other or Unknown device with a caution symbol

(see Figure 5), then the CDC driver is not installed.

Figure 5. Device Manager With LaunchPad™ Development Kit Shown as an Other Device

www.ti.com

Getting Started

SLOU452–December 2016

NFCLink Standalone Getting Started

1. To install the CDC driver, right click the MSP430 device and select Update Driver Software… (see

Figure 6).

Figure 6. Update Driver Software Using Device Manager

Getting Started

www.ti.com

10 SLOU452–December 2016

Submit Documentation Feedback

NFCLink Standalone Getting Started

2. Select Browse my computer for driver software option (see Figure 7).

Figure 7. Browse Computer for Driver Software

Autres manuels pour TRF7970A BoosterPack

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Texas Instruments Microcontrôleur

Texas Instruments

Texas Instruments CC2533EMK Manuel utilisateur

Texas Instruments

Texas Instruments MSPM0G310 Series Manuel utilisateur

Texas Instruments

Texas Instruments SimpleLink MSP432P4111 Manuel utilisateur

Texas Instruments

Texas Instruments AM437x Manuel utilisateur

Texas Instruments

Texas Instruments LP-MSPM0L1306 Manuel utilisateur

Texas Instruments

Texas Instruments CC3235 SimpleLink Series Manuel utilisateur

Texas Instruments

Texas Instruments Errata MSP430FG6426 Manuel utilisateur

Texas Instruments

Texas Instruments EK-TM4C123GXL-BOOSTXL-SENSHUB Manuel utilisateur

Texas Instruments

Texas Instruments MSP-EXP430FR5969 Manuel utilisateur

Texas Instruments

Texas Instruments MSP430G2231 Manuel utilisateur

Texas Instruments

Texas Instruments CC3235 SimpleLink Series Manuel du produit

Texas Instruments

Texas Instruments Serial Programming Adapter MSP430 Manuel utilisateur

Texas Instruments

Texas Instruments Serial Programming Adapter MSP430 Manuel utilisateur

Texas Instruments

Texas Instruments CC3100 SimpleLink Manuel utilisateur

Texas Instruments

Texas Instruments MSP430F22x4 Series Manuel utilisateur

Texas Instruments

Texas Instruments LaunchPad MSP-EXP430FR5994 Manuel utilisateur

Texas Instruments

Texas Instruments CC1125 Manuel utilisateur

Texas Instruments

Texas Instruments F280025C Manuel utilisateur

Texas Instruments

Texas Instruments TI-InnovatorHub Manuel utilisateur

Texas Instruments

Texas Instruments TMS370 Series Manuel d'utilisation et d'entretien

Texas Instruments

Texas Instruments MSP430F563x Manuel utilisateur

Texas Instruments

Texas Instruments Errata MSP430F6779 Manuel utilisateur

Texas Instruments

Texas Instruments Serial Programming Adapter MSP430 Manuel utilisateur

Texas Instruments

Texas Instruments MSP430F663x Manuel utilisateur

Manuels Microcontrôleur populaires d'autres marques

AMS

AMS AS7261 Demo Kit Manuel utilisateur

Novatek

Novatek NT6861 Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266 SDK Guide de configuration

Nuvoton

Nuvoton ISD61S00 ChipCorder Mode d’emploi

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuel utilisateur

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuel utilisateur

NEC

NEC 78GK0S/K 1+ Series Instructions d'installation et d'utilisation

Mikroe

Mikroe SEMITECH N-PLC Click Instructions d'installation et d'utilisation

Intel

Intel Agilex Manuel utilisateur

Cypress

Cypress CY4607 HX2VL Manuel utilisateur

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuel utilisateur

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266EX Mode d'emploi

Abov

Abov AC33M8128L Manuel utilisateur

Laird

Laird BL654PA Manuel utilisateur

Silicon Laboratories

Silicon Laboratories C8051F800 Manuel utilisateur

Energy micro

Energy micro EFM32 Giant Gecko Starter Kit Manuel utilisateur

Mikroe

Mikroe click Proximity 2 Manuel utilisateur