Texas Instruments TPS23525EVM-815 Manuel utilisateur

SLVUB36–October 2017

TPS23525EVM-815 Evaluation Module

User's Guide

SLVUB36–October 2017

TPS23525EVM-815 Evaluation Module

This user’s guide describes the TPS23525 evaluation module (TPS23525EVM-815). TPS23525EVM-815

contains evaluation and reference circuitry for the TPS23525, which is a low-side hot swap and dual

ORing controller targeted at telecom applications.

Contents

1 Introduction ................................................................................................................... 1

1.1 Features.............................................................................................................. 1

1.2 Applications.......................................................................................................... 2

1.3 Electrical Specifications............................................................................................ 2

2 Schematic .................................................................................................................... 3

3 General Configuration and Description .................................................................................. 4

3.1 Physical Access .................................................................................................... 4

3.2 Equipment Setup ................................................................................................... 5

3.3 Scope Considerations ............................................................................................. 5

4 Test Results ................................................................................................................. 5

5 Bill of Material .............................................................................................................. 13

List of Tables

1 TPS23525 Electrical and Performance Specifications at 25°C........................................................ 2

2 Connector Functionality .................................................................................................... 4

3 Test Points.................................................................................................................... 4

4 Jumper Descriptions......................................................................................................... 4

5 TPS23525EVM-815 Bill of Materials..................................................................................... 13

Trademarks

All trademarks are the property of their respective owners.

1 Introduction

The TPS23525 EVM provides a jump-start to anyone designing a redundant feed –48-V system. The EVM

includes input clamping to support lightning surge (up to 2 kV), various FET placeholders to support

various power levels, and an output inductor to mimic any EMI filter before the DC/DC converter.

Additionally, the EVM includes circuitry that supports auxiliary bulk capacitors. This “auxiliary bulk

capacitor” approach is useful when designing for large hold-up times (example: 10 ms) making the hot-

swap design more manageable by reducing the initial charge on the capacitor.

1.1 Features

This EVM has the following features:

• Inrush current control

• Hot-swap output short-circuit protection

• Reverse current protection

• Dual supply ORing

• Reverse hookup protection

Introduction

www.ti.com

2SLVUB36–October 2017

Submit Documentation Feedback

TPS23525EVM-815 Evaluation Module

1.2 Applications

This EVM is used in the following applications:

• Wireless infrastructure

• Telecom infrastructure

• –48-V interface

1.3 Electrical Specifications

Table 1 lists the TPS23525 electrical and performance specifications at 25°C.

Table 1. TPS23525 Electrical and Performance Specifications at 25°C

Characteristic TPS23525EVM-PWR815

Input voltage Range (Recommended) 38 V to 60 V

Input Voltage Range (Abs Max) 0 V to 150 V

Load Power 400 W

Load Output Cap 660 µF

Current Limit (Normal) 12.5 A

Current Limit (High FET VDS) 1.5 A

Typical Inrush Current 0.4 A

Hot-swap FET VDS when current transitions from high to low 20.2 V

Time Out (VDS,HS < 10 V) 2.25 ms

Time Out (10 V < VDS,HS < 20 V) 1.12 ms

Time Out (VDS,HS > 20 V) 0.23 ms

Undervoltage Threshold (Rising) 36.6 V

Undervoltage Threshold (Falling) 34.6 V

Overvoltage Threshold (Rising) 64.4 V

Overvoltage Threshold (Falling) 61.4 V

www.ti.com

Schematic

SLVUB36–October 2017

TPS23525EVM-815 Evaluation Module

2 Schematic

Figure 1 illustrates the EVM schematic.

Figure 1. TPS23525EVM-815 Schematic

General Configuration and Description

www.ti.com

4SLVUB36–October 2017

Submit Documentation Feedback

TPS23525EVM-815 Evaluation Module

3 General Configuration and Description

3.1 Physical Access

Table 2 lists the TPS23525EVM connector and functionality, Table 3 describes the test point availability,

and Table 4 describes the default jumper configuration.

Table 2. Connector Functionality

Connector Label Description

J1, J2, J3 RTN Power bus input - Tie the high-side of power-supply inputs and outputs here

J7 Neg48V_B Power bus input - Tie the low-side of power-supply B input here

J8 Vout_FLTD Output bus - Apply the low-side load here (if applicable)

J9 CAUX Connect to auxiliary bulk capacitor (if applicable)

J10 Neg48V_A Power bus input - Tie the low-side of power-supply A input here

Table 3. Test Points

Connector Label Description

TP1 RTN High-side power-supply input and high-side output load voltage

TP2 VCC Clamped voltage supply

TP3 PGB Power Good Bar

TP4 SS Soft-start pin voltage

TP5 UVEN UV pin voltage

TP6 D D pin voltage

TP7 OV OV pin voltage

TP8 GATE Gate drive output voltage for hot-swap FET

TP9 SNS Sense pin test point

TP10 TMR Timer capacitor voltage

TP11 GATEB Gate drive output voltage for Gate B ORing FET

TP12 GATEA Gate drive output voltage for Gate A ORing FET

TP13, TP15 VEE IC ground - Place voltage probe ground at this pin

TP14 Neg48VB Low-side input for power-supply B

TP16 HS_DRAIN Drain voltage of the hot-swap FET

TP17 VOUT_FLTD Low-side output for load

TP18 Neg48VA Low-side input for power-supply A

TP19 - Open-drain output for power good signal. Attach to downstream EN pin.

Table 4. Jumper Descriptions

Connector Description

J5 Jump pins 1-2 to enable UV (default), or jump pins 2-3 to tie UV to VCC (disable)

J6 Leave open to enable OV (default), or jump pins 1-2 to tie OV to GND (disable)

www.ti.com

General Configuration and Description

SLVUB36–October 2017

TPS23525EVM-815 Evaluation Module

3.2 Equipment Setup

Use the following equipment list and setup steps to work with the EVM:

• 2× power supplies capable of ≥60 V and ≥15 A (preferred)

• Resistive or electronic load – only turn on the load after the hot swap is up

• Set the input power-supply voltage to the desired operating input voltage

• Turn the power supply off

• Jump pins 1-2 on J5

• Leave pins 1-2 on J6 open

• Connect the positive voltage lead from the power-supply A to J1 (RTN). Connect the ground lead from

the power-supply A to J10 (Neg48V_A).

• Connect the positive voltage lead from the power-supply B to J3 (RTN). Connect the ground lead from

the power-supply B to J7 (Neg48V_B).

• Make sure all voltmeter or oscilloscope GNDs are tied to VEE

• Turn the power supplies on

3.3 Scope Considerations

Observe the following scope considerations:

• Most scopes have a 10-MΩresistance between scope GND and probe.

• If scope GND is tied to RTN and a probe is placed on TMR, that creates approximately 5 μA of pullup

current which can overpower the pull down of the TMR pin and result in an undesired time out.

4 Test Results

This section provides typical performance waveforms for the TPS23525EVM-815 board. Actual

performance data is affected by measurement techniques and environmental variables; therefore, these

curves are presented for reference and may differ from actual results obtained. All curves are based on

VIN = 48 V, unless stated otherwise.

No Load, Scope GND = –48V_A

Figure 2. Start Up (VIN = 54 V)

No Load, Scope GND = –48V_A

Figure 3. Start Up (VIN = 54 V)

Test Results

www.ti.com

6SLVUB36–October 2017

Submit Documentation Feedback

TPS23525EVM-815 Evaluation Module

No Load, Scope GND = –48V_A

Figure 4. Start Up (VIN = 38 V)

No Load, Scope GND = –48V_A

Figure 5. Start Up (VIN = 60 V)

VINA = 54 V, VINB = 54 V, No Load, Scope GND = RTN

Figure 6. Hot Plug Channel A and B Together

VINA = 54.5 V, VINB = 54 V, No Load, Scope GND = RTN

Figure 7. Hot Plug Channel A and B Together

VINA = 54 V; VINB = 38 V, Scope GND = RTN, Iload = 5 A

Figure 8. Hot Plug A After B

VINA = 54 V; VINB = 38 V, Scope GND = RTN, Iload = 5 A

Figure 9. Hot Plug A After B

www.ti.com

Test Results

SLVUB36–October 2017

TPS23525EVM-815 Evaluation Module

VINA = 54 V; VINB = 38 V, Scope GND = RTN, Iload = 5 A

Figure 10. Hot Plug A After B

VINA = 54.5 V; VINB = 54 V, Scope GND = RTN, No Load

Figure 11. Hot Plug A After B

Scope GND = –48V_B, No Load, After Inductor

Figure 12. Output Hot Short (VINB = 54 V)

Scope GND = –48V_B, 5-A Load, After Inductor

Figure 13. Output Hot Short (VINB = 54 V)

Scope GND = –48V_B, 5A Load, Zoomed in

Figure 14. Output Hot Short (VINB = 54 V)

Scope GND = –48V_B, 5-A Load

Figure 15. Output Hot Short (VINB = 60 V)

Test Results

www.ti.com

8SLVUB36–October 2017

Submit Documentation Feedback

TPS23525EVM-815 Evaluation Module

Scope GND = –48V_B, 5-A Load, Zoomed In

Figure 16. Output Hot Short (VINB = 60 V)

Scope GND = –48V_A

Figure 17. Gradual Overcurrent (VINA = 54 V)

Scope GND = –48V_A

Figure 18. Load Step Overcurrent

Scope Gnd = –48V_A, VIN = 54 V

Figure 19. Start Into Short

Scope Gnd = –48V_A, VIN = 54 V

Figure 20. Start Into Short

Scope Gnd = –48V_A, VIN = 54 V

Figure 21. Apply Short and Remove Short

www.ti.com

Test Results

SLVUB36–October 2017

TPS23525EVM-815 Evaluation Module

Scope GND = –48V_A, Iload = 5 A

Figure 22. 1-ms Brown Out

Scope GND = –48V_A, Iload = 5 A

Figure 23. 1-ms Brown Out

VINB = 53 V, Iload = 5 A, Scope GND = RTN

Figure 24. Supply Switch Over (Raise VINA)

VINB = 53 V (Raise VINA), Scope GND = RTN, Iload = 5 A

Figure 25. Supply Switch Over (Zoomed in)

VINA = 54.5 V; VINB = 54 V, Iload = 5 A, Scope GND = RTN

Figure 26. VINA Short

VINA = 54.5 V; VINB = 54 V, Iload = 5 A, Scope GND = RTN

Figure 27. VINA Short

Test Results

www.ti.com

10 SLVUB36–October 2017

Submit Documentation Feedback

TPS23525EVM-815 Evaluation Module

VINA = 54.5 V; VINB = 54 V, Iload = 5 A, Scope GND = RTN

Figure 28. Unplug VIN A

VINB = 60 V

Figure 29. Plug in VIN A Backwards

VINB Floating

Figure 30. Plug in VIN A Backwards

Scope GND = –48V_A, No Load

Figure 31. Undervoltage and Overvoltage (Rising)

Scope GND = –48V_A, No Load

Figure 32. Undervoltage and Overvoltage (Falling)

Scope GND = RTN, 5-A Load, Per IEC61000-4-5

Figure 33. –2-kV (2 Ω) Lightning Surge

Table des matières

Autres manuels Texas Instruments Unité de contrôle

Texas Instruments

Texas Instruments bq24165 Manuel utilisateur

Texas Instruments

Texas Instruments MLTLDO2EVM-037 Manuel utilisateur

Texas Instruments

Texas Instruments INA901EVM-CVAL Manuel utilisateur

Texas Instruments

Texas Instruments PurePath Digital TAS5342DDV6EVM Manuel utilisateur

Texas Instruments

Texas Instruments TPA6017A2 Manuel utilisateur

Texas Instruments

Texas Instruments TAS5514B Manuel utilisateur

Texas Instruments

Texas Instruments TPS53128 Manuel utilisateur

Texas Instruments

Texas Instruments TSW12QJ1600 Manuel utilisateur

Texas Instruments

Texas Instruments TPS62737 Manuel utilisateur

Texas Instruments

Texas Instruments TPS254900AQ1EVM-003 Manuel utilisateur

Texas Instruments

Texas Instruments ADC12DJ3200 Manuel utilisateur

Texas Instruments

Texas Instruments TPS22810EVM Manuel utilisateur

Texas Instruments

Texas Instruments TPS40075EVM-001 Manuel utilisateur

Texas Instruments

Texas Instruments LMK00308EVM Manuel utilisateur

Texas Instruments

Texas Instruments FPD23DAEVM Manuel utilisateur

Texas Instruments

Texas Instruments TCA8424 Manuel utilisateur

Texas Instruments

Texas Instruments LMG352 EVM-04 Series Manuel utilisateur

Texas Instruments

Texas Instruments LM76005QEVM Manuel utilisateur

Texas Instruments

Texas Instruments BoosterPack Educational Plug-in Module Mark II... Manuel utilisateur

Texas Instruments

Texas Instruments SimpleLink CC3220MOD Series Manuel utilisateur

Texas Instruments

Texas Instruments AFE5818 Manuel utilisateur

Texas Instruments

Texas Instruments LM74700DDFEVM Manuel utilisateur

Texas Instruments

Texas Instruments TPS40190EVM-001 Manuel utilisateur

Texas Instruments

Texas Instruments INA190EVM Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur