Texas Instruments TUSB2E11 Manuel utilisateur
User’s Guide
TUSB2E11 Evaluation Module User's Guide
ABSTRACT
This is the user's guide for the evaluation module (EVM) of the TUSB2E11 single channel eUSB2 to USB
2.0 repeater. The purpose of the user's guide is to facilitate easy set up for validation and development of
the TUSB2E11 device. An overview of the TUSB2E11EVM is provided in this user’s guide, which includes
highlighting its key features, operating conditions, and how to adjust the EVM for use in various systems.
Table of Contents
1 Introduction.............................................................................................................................................................................2
2 EVM Quick Setup Instructions...............................................................................................................................................2
3 EVM Configuration Using Jumpers.......................................................................................................................................3
3.1 Default EVM Configuration.................................................................................................................................................3
3.2 EVM Power Configuration..................................................................................................................................................3
3.3 TUSB2E11 Functional Modes............................................................................................................................................ 4
4 TUSB2E11EVM Internal Lab Use Only.................................................................................................................................. 4
5 Layout Notes........................................................................................................................................................................... 4
6 Schematic................................................................................................................................................................................5
7 Bill of Materials....................................................................................................................................................................... 6
List of Figures
Figure 2-1. TUSB2E11EVM Block Diagram.................................................................................................................................2
Figure 6-1. TUSB2E11EVM Schematic....................................................................................................................................... 5
List of Tables
Table 3-1. TUSB2E11 Configuration Pins....................................................................................................................................3
Table 7-1. TUSB2E11EVM Bill of Materials................................................................................................................................. 6
Trademarks
All trademarks are the property of their respective owners.
www.ti.com Table of Contents
SLLU229 – MAY 2022
Submit Document Feedback
TUSB2E11 Evaluation Module User's Guide 1
Copyright © 2022 Texas Instruments Incorporated
1 Introduction
The TUSB2E11EVM is designed for the TUSB2E11 device, which is an USB 2.0 compliant eUSB2 to USB 2.0
repeater supporting both device and host modes, as well as dual role applications. The TUSB2E11 repeater
supports USB 2.0 low speed (LS) and full speed (FS) signals and high speed (HS) signals.
2 EVM Quick Setup Instructions
To start using the TUSB2E11EVM, the EVM requires power, a USB connection, and an eUSB2 connection:
• The TUSB2E211EVM incorporates a Micro-AB USB 2.0 port that can be used to connect the USB signals of
the repeater to a standard USB host, hub, or devices. 5M cable lengths are supported.
• For eUSB2, the EVM has a pair of SMP connectors for connecting eUSB2 signals to eUSB2 SoCs or test
equipment.
• Depending on the switch settings, the EVM can be powered from an external 5 V wall supply, bench power
supplies, or even through the USB connector.
• The TUSB2E11EVM also incorporates an external reset push button in addition to a regular power reset
circuit.
Figure 2-1. TUSB2E11EVM Block Diagram
Introduction www.ti.com
2TUSB2E11 Evaluation Module User's Guide SLLU229 – MAY 2022
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
3 EVM Configuration Using Jumpers
Table 3-1 lists the headers provided for configuration of the TUSB2E11 by default.
Table 3-1. TUSB2E11 Configuration Pins
Reference Designator JMP Control Configuration
J1 [1, 2] VBUS Enable USB VBUS
J2 [1, 2] and J7 [1, 2] SDA. SCL Enable I2C Mode
J3 [1, 2] UART Enable repeater mode
J12 – install 5 V to VBUS Enable 5 V to VBUS
J13, J14 – install 3.3 V Enable 3.3 V LDO
J15, J16 – install 1.8 V Enable 1.8 V LDOs
3.1 Default EVM Configuration
When the TUSB2E11EVM is shipped, it is configured to be either wall powered from a 5 V source connected to
J11 or bus powered through the USB connector, J9. The 5 V wall power supply from CUI, Digikey# 102-3584-N,
or similar can be used. Please note that if a 5 V supply is connected to J11, VBUS will be supplied on the J9
USB connector unless the jumper on J1[1, 2] is removed.
I2C mode is enabled by default on the EVM. The pullups on SDA and SCL are installed through the jumpers on
J2 [1,2] and J7 [1,2]. A 1.8 V I2C master can be connected to the SDA, SCL, and GND connections at J6 and
access the TUSB2E11 at address 3Eh. Also, the TUSB2E11EVM is set to repeater mode by J3 [1, 2].
All power jumpers are installed by default (J13, J14, J15, and J16). These can be removed to externally supply
power or take current measurements.
3.2 EVM Power Configuration
3.2.1 Power Options
As noted earlier, the TUSB2E11EVM can configured to be either wall powered from a 5 V source connected to
J11 or bus powered through the USB connector, J9. The 5 V wall power supply from CUI, Digikey# 102-3584-N,
or similar can be used.
3.2.2 Host Mode
When the TUSB2E11EVM is connected to an eUSB2 SoC that is in host mode, it should supply 5 V VBUS on
its USB connector. A 5 V source should be connected to J11 or through a bench supply to J12. The J1 jumper
should be installed on pins 1 and 2 to route the 5 V VBUS to the USB connector.
3.2.3 Device Mode – Self Powered
When the TUSB2E11EVM is connected to an eUSB2 SoC that is in device mode, it should not supply 5 V VBUS
on its USB connector. The TUSB2E11EVM can be powered from the USB connector or it can be self powered. If
it is self powered, the jumper on J12 should be removed. A 5 V source should be connected to J11 or through a
bench supply to pin 2 of J12. The J1 jumper should be removed from pins 1 and 2.
3.2.4 Device Mode – Bus Powered
When the TUSB2E11EVM is connected to an eUSB2 SoC that is in device mode, it should not supply 5 V VBUS
on its USB connector. The TUSB2E11EVM can be powered from the USB connector or it can be self powered. If
it is bus powered, the jumper on J12 should be installed and the J1 jumper should be installed on pins 1 and 2 to
route the 5 V from the USB connector to the EVM.
www.ti.com EVM Configuration Using Jumpers
SLLU229 – MAY 2022
Submit Document Feedback
TUSB2E11 Evaluation Module User's Guide 3
Copyright © 2022 Texas Instruments Incorporated
3.3 TUSB2E11 Functional Modes
3.3.1 I2C Mode
When SDA and SCL are pulled high at reset, the TUSB2E11 is in I2C Mode, where the TUSB2E11 typically acts
as an eUSB2 to USB repeater. The repeater can be further configured using the 1.8 V I2C interface accessible
at J6. I2C configuration, however, is not required for the repeater to operate. Please note that GPIO0 must be
pulled high for normal I2C repeater mode operation.
3.3.2 GPIO Mode
The TUSB2E11 repeater can also be configured by strap settings instead of I2C. When SCL is low at reset,
the TUSB2E11 will use the strap settings on the GPIOs to determine the repeater configuration. Please see the
TUSB2E11 data sheet for more information.
3.3.3 UART Mode
In UART mode, the TUSB2E11 acts a UART to UART repeater to support in-system debug. UART mode can
be entered by pulling the GPIO0 low when the TUSB2E11 is in I2C mode or by setting SCL high and SDA low
at reset, and setting the GPIO0 low. If SCL is high and SDA is low at reset, and GPIO0 is pulled high, then the
TUSB2E11 will be in a non-functional state.
4 TUSB2E11EVM Internal Lab Use Only
There are several features of the TUSB2E11EVM that are reserved for internal lab use only.
1. Under normal use conditions, the resistor on R18 should not be installed. In addition, adding the resistors and
capacitor, R12, R14, and C3 is not recommended for end users.
2. 1.2 V IO operation is not enabled on the default TUSB2E11EVM.
3. The VBUS control functions implemented by U5 and U6 are not currently supported.
5 Layout Notes
The TUSB2E11EVM was laid out with the following considerations:
• USB signals impedance controlled 90 Ω differential ± 5%
• eUSB signals impedance controlled 45 Ω signal ended ± 5%
• USB 2.0 and eUSB signal pairs routed with matched trace lengths and minimal vias.
• All other signals to be impedance controlled 45 Ω ± 10% or 50 Ω ± 10%
General information about the PCB is provided below:
• Finished board thickness: .062 ± 10% – necessary for socket
• Copper weight: 1 oz start internal, 1/2 oz start external
• Laminate material: FR4 Polyclad 370 or equivalent
A four layer stack-up was used for the TUSB2E11EVM.
Drill notes on board stack up to account for the small BGA breakout:
1. L1 – L2 (laser drill) used for small pitch BGA break out
2. L2 – L3 (mechanical drill) completes the small pitch BGA breakout
3. L3 – L4 (laser drill) for VPP
EVM Configuration Using Jumpers www.ti.com
4TUSB2E11 Evaluation Module User's Guide SLLU229 – MAY 2022
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
7 Bill of Materials
Table 7-1 lists the devices installed on the TUSB2E11EVM. The devices that are in the schematic, but are not installed on the EVM, are still listed in the
bill of materials (BOM) and are marked with DNI under the Part column.
Table 7-1. TUSB2E11EVM Bill of Materials
Item Quantity Reference Part Manufacturer Manufacturer Part Number
1 5 C1, C4, C5, C7, and C19 .1 µF Yageo CC0402KRX5R6BB104
2 1 C2 2.2 µF TDK CGA4J3X7R1C225K125AB
3 1 C3 .1 µF – DNI(1) Yageo CC0402KRX5R6BB104
4 5 C6, C9, C13, C15, and C16 .01 µF Kemet C0402C103K3RACTU
5 1 C8 47 µF TDK C3225X5R1A476M250AC
6 2 C10 and C12 1 µF Kemet C0805C105K4RACTU
7 3 C11, C14, and C17 10 µF Kemet C0805C106K8PACTU
8 1 C18 22 µF Murata GRM21BR61A226ME51L
9 1 JP1 HDR3X2 Sullins PEC03DAAN
10 6 J1, J2, J3, J4, J6, and J7 HDR3X1 Sullins PEC03SAAN
11 6 J5, J12, J13, J14, J15, and
J16
HDR2X1 Sullins PEC02SAAN
12 2 J8 and J10 SMP Rosenberger 19S201-40ML5
13 1 J9 USB Micro AB Amphenol FCI 10104111-0001LF
14 1 J11 DC JACK CUI PJ1-022-SMT-TR
15 1 PCB1 HSDC090 Any HSDC090
16 2 R1 and R9 1K Yageo RT0402BRE071KL
17 3 R2, R3, and R4 20K Yageo RC0402JR-0720KL
18 1 R5 100K Yageo RC0402JR-07100KL
19 2 R6 and R24 10K Yageo RC0402FR-0710KP
20 1 R7 1M Yageo RC0402FR-071ML
21 1 R8 36K Yageo RC0402JR-0736K
22 2 R10 and R17 0 Vishay Dale CRCW02010000Z0ED
23 1 R11 90.9 Stackpole RMCF0402FT90R9
24 2 R12 and R14 90.9 – DNI(1) Stackpole RMCF0201FT90R9
25 1 R13 2K Stackpole RMCF0402FT2K00
26 1 R15 2.2K Yageo RC0402FR-072K2L
27 1 R16 5.6K Stackpole RMCF0402FT5K60
28 1 R18 0 – DNI(1) Yageo RC0402JR-070RL
29 1 R19 0 Yageo RC0402JR-070RL
30 2 R20 and R22 28.0K Yageo RC0402FR-0728KL
Schematic www.ti.com
6TUSB2E11 Evaluation Module User's Guide SLLU229 – MAY 2022
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Table 7-1. TUSB2E11EVM Bill of Materials (continued)
Item Quantity Reference Part Manufacturer Manufacturer Part Number
31 2 R21 and R23 56.2K Yageo RT0402BRD0756K2
32 4 SCRW1, SCRW2, SCRW3,
and SCRW4
NY PMS 440 005 PH B&F Fastener NY PMS 440 0050 PH
33 13 SHNT1, SHNT2, SHNT3,
SHNT4, SHNT5, SHNT6,
SHNT7, SHNT8, SHNT9,
SHNT10, SHNT11, SHNT12,
and SHNT13
QPC02SXGN-RC Sullins QPC02SXGN-RC
34 4 STDOFF1, STDOFF2,
STDOFF3, and STDOFF4
1902E Keystone 1902E
35 1 SW1 PB Switch OMRON B3U-1000P
36 1 TP1 TEST POINT TE Connectivity RCU-0C
37 1 U1 TUSB2E11 Texas Instruments TUSB2E11YCG
38 1 U2 TPS73633 Texas Instruments TPS73633DRB
39 2 U3 and U4 TPS73601 Texas Instruments TPS73601DRB
40 1 U5 SN74AUP1T34 Texas Instruments SN74AUP1T34DCKR
41 1 U6 TPS2001D Texas Instruments TPS2001DDBVR
(1) This device is in the schematic, but is not installed on the EVM
www.ti.com Schematic
SLLU229 – MAY 2022
Submit Document Feedback
TUSB2E11 Evaluation Module User's Guide 7
Copyright © 2022 Texas Instruments Incorporated
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2022, Texas Instruments Incorporated
Table des matières
Autres manuels Texas Instruments Matériel informatique
Texas Instruments
Texas Instruments BoosterPack BOOSTXL-ADS7142-Q1 Manuel utilisateur
Texas Instruments
Texas Instruments TMS320 DSP Manuel utilisateur
Texas Instruments
Texas Instruments Sitara AM1335 Series Manuel utilisateur
Texas Instruments
Texas Instruments TLV320AIC12KEVMB-K Manuel utilisateur
Texas Instruments
Texas Instruments MSP-FET430 Manuel utilisateur
Texas Instruments
Texas Instruments ADS125H02 Manuel utilisateur
Texas Instruments
Texas Instruments TPS3801 Manuel utilisateur
Texas Instruments
Texas Instruments SimpleLink CC2651R3SIPA Manuel utilisateur
Texas Instruments
Texas Instruments TPS3813 Q1EVM Series Manuel utilisateur
Texas Instruments
Texas Instruments TMS320C6201 Manuel utilisateur
Texas Instruments
Texas Instruments TMS320C642x DSP Manuel utilisateur
Texas Instruments
Texas Instruments TMS320C6000 DSP Manuel utilisateur
Texas Instruments
Texas Instruments DRA821 Manuel utilisateur
Texas Instruments
Texas Instruments bq24650EVM Manuel utilisateur
Texas Instruments
Texas Instruments TPS65910 EVM Manuel utilisateur
Texas Instruments
Texas Instruments BQ77307 Manuel utilisateur
Texas Instruments
Texas Instruments TMS320C6000 DSP Manuel utilisateur
Texas Instruments
Texas Instruments Piccolo F280049 Manuel utilisateur
Texas Instruments
Texas Instruments TRIS TMS37122 Manuel utilisateur
Texas Instruments
Texas Instruments CC3100BOOST Manuel utilisateur
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
