Texas Instruments TMDXEVM6472 Manuel utilisateur

TMS320C6472 Evaluation Module

Quick Setup Guide

TMDXEVM6472

Getting Started:

The EVMC6472 ships with a Power On self Test (POST) flashed

in to I2C EEPROM. The POST will be automatically executed

when the board is powered ON. POST will perform memory

test and EMAC internal loopback test. At 'power on' state the

user LEDs will glow. The LEDs will continue to glow while the

POST utility is being copied from EEPROM to IRAM. User LEDs

will turn OFF once the POST is copied to IRAM.

User LED-1 and user LED-2 will blink to indicate successful

executions of memory and EMAC internal loopback tests

respectively. These LEDs will turn OFF after completion of the

tests.

Please refer EVM User Guide for software installation and

other details.

Helpful Hints:

• Plug in all the cables before turning the EVM ON to

ensure proper grounding.

• Do not unnecessarily flex the boards, while inserting

cables. Excessive flexing can break the PCB traces.

Online Documentation

Most of the information on EVM6472 is available online. Some

of the most commonly used resources are mentioned below:

EVM6472 Information:

http://www.einfochips.com/TI-TMS320C6472-EVM.php

This link contains:

• Hardware & software details

• User Guide

• Technical Reference Manual

• TMS320C6472 Datasheet

• Frequently Asked Questions (FAQ)

C6472 DSP Information:

http://focus.ti.com/docs/prod/folders/print/tms320c6472.html

TI Worldwide Technical Support

Internet

TI Semiconductor Product Information Center Home Page

support.ti.com

TI Semiconductor KnowledgeBase Home page

support.ti.com/sc/knowledgebase

Product Information Centers

Americas

Phone +1(972) 644-5580 Fax +1(972)927-6377

Internet/Email support.ti.com/sc/pic/americas.htm

Europe, Middle East and Africa

Phone

European Free Call 00800-ASK-TEXAS

(00800 275 83927)

International +49 (0) 8161 80 2121

Russian Support +7 495 981 0701

Note: The European Free Call (Toll Free) number is not active in all

countries. If you have technical difficulty calling the free call

number, please use the international number above.

Fax +(49) (0) 8161 80 2045

Internet support.ti.com/sc/pic/euro.htm

Japan

Fax

International +81-3-3344-5317 Domestic 0120-81-0036

Internet/Email

International support.ti.com/sc/pic/japan.htm

Domestic www.tij.co.jp/pic

Asia

Phone

International

Domestic Toll-Free-Number Toll-Free-Number

Australia Malaysia

China New Zealand

Hong Kong Philippines

India Singapore

Indonesia Taiwan

Korea Thailand

Fax Email [email protected]

[email protected]

Internet support.ti.com/sc/pic/asia.htm

Important Notice: The products and services of Texas Instruments

Incorporated and its subsidiaries described herein are sold subject to TI's

standard terms and conditions of sale. Customers are advised to obtain the

most current and complete information about TI products and services

before placing orders. TI assumes no liability for applications assistance,

customer's applications or product designs, software performance, or

infringement of patents. The publication of information regarding any other

company's products or services does not constitute TI's approval, warranty or

endorsement thereof.

The floating bar is a trademark of Texas Instruments.

All other trademarks are the property of their respective owners

+91-80-413816651-

800-999-084

800-820-8682

800-96-5941

1-800-425-7888

001-803-8861-1006

080-551-2804

+886-2-2378-6808

1-800-80-3973

0800-446-934

1-800-765-7404

800-886-1028

0800-006800

001-800-886-0010

Dual Giga Ethernet

Boot Mode/Configuration

Settings

RS232-

Serial

USB mini-B

C6472

(6 Core DSP)

HPI - DC

LEDs-I2C

AMC-

Type B+

Cold

Reset

On-Board

Embedded

Emulation Warm

Reset

JTAG-

FPGA

NAND Flash

128 MB

User

Switches

User

LEDs

FPGA

JTAG-DSP DDR2 RAM

256 MB 12V DC

w w w . e i n f o c h i p s . c o m

The TMDXEVM6472 (Evaluation Module) kit includes:

TMS320C6472 Evaluation Module (Printed circuit board

assembly)

Power supply and power cord

USB Cable for on-board JTAG emulation

Ethernet cable

Software (DVD) and documentation

C6472 Evaluation Module

3Connect Ethernet switch /

router / PC to the lower Giga

Ethernet port (J3) of EVM6472

board using an Ethernet

cable to access EMAC0. Use

upper Giga Ethernet port of

J3 to access EMAC1.

Connect the USB miniB

cable to J7 plug for on

board embedded

emulation, as shown in

figure. (For use with CCS

debugger only)

1a The EVMC6472 is also shipped

with an Out-Of-Box Demo application

flashed into NAND. This is a network

based application which starts an HTTP

server and a TELNET server with the

following static IP address:

192.168.2.100. The application enables

the following:

User switch 1 OFF - Static IP set as

192.168.2.100 (recommended)

User switch 1 ON - Obtains IP address

from DHCP server

In order to connect to the board, the

test PC should be configured with

static IP address: 192.168.2.101. Once

the User LEDs are OFF (indicating

successful NAND boot) the user can

access the following URL through a

browser to view Out-Of-Box demo:

http://192.168.2.100

Ensure EVM

configuration switches

are set as shown.

11aTo run

demo through

NAND, configure

the switches as

shown above.

Out-Of-Box Connect the 12V DC

power adapter

(supplied with the kit) to

power jack (J6).

Autres manuels Texas Instruments Matériel informatique

Texas Instruments

Texas Instruments C28 Series Manuel utilisateur

Texas Instruments

Texas Instruments TPS65910 EVM Manuel utilisateur

Texas Instruments

Texas Instruments CC3100 SimpleLink Manuel utilisateur

Texas Instruments

Texas Instruments CC2533 Manuel d'installation

Texas Instruments

Texas Instruments eZ430-TMS37157 Manuel utilisateur

Texas Instruments

Texas Instruments DRV603EVM Manuel utilisateur

Texas Instruments

Texas Instruments TMS320*2801 Series Manuel utilisateur

Texas Instruments

Texas Instruments SimpleLink CC1312PSIP Manuel utilisateur

Texas Instruments

Texas Instruments SimpleLink CC3200 Wi-Fi Manuel utilisateur

Texas Instruments

Texas Instruments INA149 Manuel utilisateur

Texas Instruments

Texas Instruments OMAP35 Series Manuel utilisateur

Texas Instruments

Texas Instruments ADS8365MEVM Manuel utilisateur

Texas Instruments

Texas Instruments Hercules RM48 Manuel utilisateur

Texas Instruments

Texas Instruments DP83867E Manuel utilisateur

Texas Instruments

Texas Instruments TMS320F2837 D Series Manuel utilisateur

Texas Instruments

Texas Instruments TPS3813 Q1EVM Series Manuel utilisateur

Texas Instruments

Texas Instruments CC1101DK Manuel utilisateur

Texas Instruments

Texas Instruments TMS320C55 Series Manuel utilisateur

Texas Instruments

Texas Instruments PGA309EVM Manuel utilisateur

Texas Instruments

Texas Instruments BoosterPack BOOSTXL-ADS7142-Q1 Manuel utilisateur

Texas Instruments

Texas Instruments PHP1500 Manuel utilisateur

Texas Instruments

Texas Instruments AM64 Series Manuel utilisateur

Texas Instruments

Texas Instruments LM95172EVM Manuel utilisateur

Texas Instruments

Texas Instruments TPS65941515-Q1 Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur