Tektronix TLA7PG2 Manuel utilisateur

Instructions

TLA7PG2

Pattern Generator Module

071-1306-00

*P071130600*

071130600

Warning

The servicing instructions are for use by qualified

personnel only. To avoid personal injury, do not

perform any servicing unless you are qualified to

do so. Refer to all safety summaries prior to

performing service.

www.tektronix.com

are protected by United States copyright laws and international treaty provisions.

Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the

Rights in Technical Data and Computer Software clause at DFARS 252.227-7013, or subparagraphs (c)(1) and (2) of the

Commercial Computer Software -- Restricted Rights clause at FAR 52.227-19, as applicable.

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes

that in all previously published material. Specifications and price change privileges reserved.

Tektronix, Inc., 14200 SW Karl Braun Drive, Beaverton, OR 97077

TEKTRONIX, TEK, TLAVu, PatGenVu, and MagniVu are registered trademarks of Tektronix, Inc.

HARDWARE WARRANTY

Tektronix warrants that the products that it manufactures and sells will be free from defects in materials and workmanship

for a period of one (1) year from the date of shipment. If a product proves defective during this warranty period, Tektronix,

at its option, either will repair the defective product without charge for parts and labor, or will provide a replacement in

exchange for the defective product.

In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration of the

warranty period and make suitable arrangements for the performance of service. Customer shall be responsible for

packaging and shipping the defective product to the service center designated by Tektronix, with shipping charges prepaid.

Tektronix shall pay for the return of the product to Customer if the shipment is to a location within the country in which the

Tektronix service center is located. Customer shall be responsible for paying all shipping charges, duties, taxes, and any

other charges for products returned to any other locations.

This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate

maintenance and care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage resulting

from attempts by personnel other than Tektronix representatives to install, repair or service the product; b) to repair

damage resulting from improper use or connection to incompatible equipment; c) to repair any damage or malfunction

caused by the use of non-Tektronix supplies; or d) to service a product that has been modified or integrated with other

products when the effect of such modification or integration increases the time or difficulty of servicing the product.

THIS WARRANTY IS GIVEN BY TEKTRONIX IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR

IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TEKTRONIX’ RESPONSIBILITY TO

REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND EXCLUSIVE REMEDY PROVIDED TO

THE CUSTOMER FOR BREACH OF THIS WARRANTY. TEKTRONIX AND ITS VENDORS WILL NOT BE

LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES IRRESPECTIVE

OF WHETHER TEKTRONIX OR THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH

DAMAGES.

TLA7PG2 Pattern Generator Module Instructions i

Table of Contents

General Safety Summary iii...................................

Preface v...................................................

Related Documentation v...........................................

Contacting Tektronix vi.............................................

Pattern Generator Module Introduction 1.......................

Probes 1.........................................................

Pattern Generator Program 1.........................................

Setting Up the Pattern Generator Module 3.....................

Module Setup Window 3............................................

Channel Setup Window 4...........................................

Probe Setup Window 5.............................................

Signal Setup Window 5.............................................

Setting Up the Pattern Generator Program 7....................

Block Definition Window 7.........................................

Sequence Definition Window 8.......................................

Subsequence Definition Window 11....................................

Event Definition Window 11..........................................

Appendix A: TLA7PG2 Pattern Generator Module Characteristics 13

Appendix B: Pattern Generator Physical-Logical Conversion 17.....

Table of Contents

ii TLA7PG2 Pattern Generator Module Instructions

List of Figures

Figure 1: Block diagram of the pattern generator module 1........

Figure 2: Module Setup window 4.............................

Figure 3: Channel Setup window 4.............................

Figure 4: Probe Setup window 5...............................

Figure 5: Signals Setup window 6..............................

Figure 6: Block Definition window 7...........................

Figure 7: Listing window 8...................................

Figure 8: Sequence Definition window 9........................

Figure 9: Drag the vertical bar to the left to display the sequence

flow graphic 10...........................................

Figure 10: Sequence flow graphic 10............................

Figure 11: Subsequence Definition window 11....................

Figure 12: Event Definition window 12..........................

List of Tables

Table i: Tektronix TLAPG2 Pattern Generator Module

documentation v........................................

Table 1: PG module electrical specification, operational mode 13....

Table 2: PG module clocking 14................................

Table 3: PG module event processing 14........................

Table 4: PG module inter-module interactions 15.................

Table 5: PG module merged PG modules 15.....................

Table 6: PG module mechanical 15.............................

Table 7: For Signal 1, 2, and 3, 4, (logical function AND) 17........

Table 8: For Signal 3, 4 (logical function OR) 17..................

TLA7PG2 Pattern Generator Module Instructions iii

General Safety Summary

Review the following safety precautions to avoid injury and prevent damage to

this product or any products connected to it.

To avoid potential hazards, use this product only as specified.

Only qualified personnel should perform service procedures.

While using this product, you may need to access other parts of the system. Read

the General Safety Summary in other system manuals for warnings and cautions

related to operating the system.

Connect and Disconnect Properly. Do not connect or disconnect probes or test

leads while they are connected to a voltage source.

Ground the Product. This product is indirectly grounded through the grounding

conductor of the mainframe power cord. To avoid electric shock, the grounding

conductor must be connected to earth ground. Before making connections to the

input or output terminals of the product, ensure that the product is properly

grounded.

Observe All Terminal Ratings. To avoid fire or shock hazard, observe all ratings

and markings on the product. Consult the product manual for further ratings

information before making connections to the product.

Do not apply a potential to any terminal, including the common terminal, that

exceeds the maximum rating of that terminal.

Do Not Operate Without Covers. Do not operate this product with covers or panels

removed.

Use Proper Fuse. Use only the fuse type and rating specified for this product.

Avoid Exposed Circuitry. Do not touch exposed connections and components

when power is present.

Do Not Operate With Suspected Failures. If you suspect there is damage to this

product, have it inspected by qualified service personnel.

Do Not Operate in Wet/Damp Conditions.

Do Not Operate in an Explosive Atmosphere.

Keep Product Surfaces Clean and Dry.

Provide Proper Ventilation. Refer to the manual’s installation instructions for

details on installing the product so it has proper ventilation.

Terms in this Manual. These terms may appear in this manual:

Symbols and Terms

General Safety Summary

iv TLA7PG2 Pattern Generator Module Instructions

WARNING. Warning statements identify conditions or practices that could result

in injury or loss of life.

CAUTION. Caution statements identify conditions or practices that could result in

damage to this product or other property.

Terms on the Product. These terms may appear on the product:

DANGER indicates an injury hazard immediately accessible as you read the

marking.

WARNING indicates an injury hazard not immediately accessible as you read the

marking.

CAUTION indicates a hazard to property including the product.

Symbols on the Product. The following symbols may appear on the product:

CAUTION

Refer to Manual

TLA7PG2 Pattern Generator Module Instructions v

Preface

This manual provides high-level information for use of the Tektronix TLAPG2

Pattern Generator Module. Use this manual together with the Pattern Generator

online help to use your Tektronix pattern generator.

Refer to the TLA700 Series Logic Analyzer Instruction Manual to install and

configure the Tektronix pattern generator module.

Related Documentation

In addition to this instruction manual, the documentation listed in Table iis

available for your Tektronix logic analyzer product. For documentation not

specified in the table, contact your local Tektronix representative.

Table i: Tektronix TLAPG2 Pattern Generator Module documentation

Location TLA Documentation

Documents available in printed form and downloadable from the Tektronix web site.

tektronix.com

Tektronix Logic Analyzer Family User Manual

TLA700 Series Installation Manual

TLA7PG2 Probe Instruction Manual

TLA7UP Field Upgrade Kit Instructions

Documents available as PDF files on the documentation CD.

Tektronix Logic Analyzer Family User Manual

TLA700 Series Installation Manual

Tektronix Pattern Generator Programmatic Interface (PPI.com)

TLA7PG2 Probe Instruction Manual

PatGenVu Readme

Preface

vi TLA7PG2 Pattern Generator Module Instructions

Contacting Tektronix

Phone 1-800-833-9200*

Address Tektronix, Inc.

Department or name (if known)

14200 SW Karl Braun Drive

P.O. Box 500

Beaverton, OR 97077

USA

Web site www.tektronix.com

Sales support 1-800-833-9200, select option 1*

Service support 1-800-833-9200, select option 2*

Technical support Email: techsupport@tektronix.com

1-800-833-9200, select option 3*

6:00 a.m. -- 5:00 p.m. Pacific time

*This phone number is toll free in North America. After office hours, please leave a

voice mail message.

Outside North America, contact a Tektronix sales office or distributor; see the

Tektronix web site for a list of offices.

Autres manuels pour TLA7PG2

Table des matières

Autres manuels Tektronix Unité de contrôle

Tektronix

Tektronix TM 5006 Manuel utilisateur

Tektronix

Tektronix TM 506 Manuel utilisateur

Tektronix

Tektronix TM 5003 Manuel utilisateur

Tektronix

Tektronix KEITHLEY 7700 Manuel utilisateur

Tektronix

Tektronix VX4790A Manuel utilisateur

Tektronix

Tektronix ECO170A Manuel utilisateur

Tektronix

Tektronix 80E01 Manuel utilisateur

Tektronix

Tektronix 80C14 Manuel utilisateur

Tektronix

Tektronix TDS3SDI Manuel d'utilisation et d'entretien

Tektronix

Tektronix 80E02 Manuel utilisateur

Tektronix

Tektronix VX4730 Manuel utilisateur

Tektronix

Tektronix TDS3TRG Manuel utilisateur

Tektronix

Tektronix VX4240 Manuel utilisateur

Tektronix

Tektronix L3 Manuel utilisateur

Tektronix

Tektronix Keithley 7706 Manuel utilisateur

Tektronix

Tektronix TM 515 Manuel utilisateur

Tektronix

Tektronix 80A02 Manuel utilisateur

Tektronix

Tektronix ECO422D Manuel d'utilisation et d'entretien

Tektronix

Tektronix KEITHLEY 7703 Manuel utilisateur

Tektronix

Tektronix 80C00 Manuel utilisateur

Tektronix

Tektronix ECO8000 Series Manuel utilisateur

Tektronix

Tektronix KEITHLEY 7710 Manuel utilisateur

Tektronix

Tektronix TM 5006 Manuel utilisateur

Tektronix

Tektronix TDS3LIM Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur