Tecnoware EXA 2.6 Manuel utilisateur

Uninterruptible Power Supply

EXA 1.1

EXA 1.5

EXA 2.2

EXA 2.6

EXA 3.2

User’s manual

UPS EXA 1.1-1.5-2.2-2.6-3.2 1 User’s manual

Inde

Safety Warnings ................................................................................ 2

Introduction ................................................................................. 3

General Characteristics ................................................................... 4

Receipt and site selection ................................................................ 4

EXTERNAL DESCRIPTION .................................................................. 5

4.1

Front Panel ............................................................................. 5

4.1.1

LCD Dis lay .................................................................................6

4.2

Rear Side ................................................................................ 7

Electrical Installation and First Start Up ............................................... 8

Functioning ................................................................................. 9

6.1

Normal Mode ........................................................................... 9

6.2

Battery Mode ........................................................................... 9

6.3

Low Battery and Automatic Restart ................................................. 9

6.4

Load Control .......................................................................... 10

6.5

Fault Condition ...................................................................... 10

Communication Interfaces .............................................................. 10

Technical Characteristics ................................................................ 11

Maintenance ............................................................................... 12

9.1

UPS Cleaning ......................................................................... 12

9.2

Battery ................................................................................ 12

9.3

O erator Safety ...................................................................... 12

Troubleshooting ........................................................................... 13

Conformity to the European Directives ................................................... 14

Product Disposal ............................................................................... 14

Lead Batteries ................................................................................. 14

All trademarks are ro erty of their res ective owners.

TECNOWARE s.r.l.

Via Montetrini, 2E – Molino del Piano – Florence – Italy

www.tecnoware.com

Edition: June 2011 – version: 1.0

No art of this manual may be re roduced, even artially, without the

authorisation of TECNOWARE s.r.l.

TECNOWARE s.r.l. reserves the right to change s ecifications at any time

and without notice.

User’s manual 2 UPS EXA 1.1-1.5-2.2-2.6-3.2

Safety Warnings



Read this manual carefully and completely before installing and using the TECNOWARE EXA

Uninterruptible Power Supply, which, from here after, will also be referred to as UPS.



This manual should be kept close to the UPS and read before the UPS is installed and used.



The UPS must be used only by properly trained personnel. To ensure correct and safe

operations, it is necessary that operators and maintenance personnel observe the general

safety Standards as well as the specific instructions included in this manual.



Risk of electric shock: do not remove the cover. The UPS contains internal parts, which are at a

high Voltage and are potentially dangerous, capable of causing injury or death by electric

shock.



There are no internal parts in the UPS, which are user serviceable. Any repair or maintenance

work must be performed e clusively by qualified technical personnel authorized by

TECNOWARE. TECNOWARE declines any responsibility if this warning is disregarded.



Warning to the technical personnel authorized for Service: since internal components are

connected to the batteries, they will remain powered, and therefore dangerous, even after the

UPS has been disconnected from AC power mains. Before any repair or maintenance work,

disconnect the batteries, by removing the positive cable (red colour) from the positive pole of

the battery.



It is compulsory to ground the UPS according to Safety Standards. The AC mains power supply

socket used to power the UPS must have an earth connection.



In the event of AC main power supply failure (when the UPS works in Battery mode), do not

unplug the power supply cable to the UPS to ensure earth continuity to the connected loads.



Since the AC mains power supply cable acts as a separation device, the AC mains power socket

used to supply the UPS and/or the rear side of the UPS must be accessible to easily disconnect

the cable in case of dangerous conditions.



Risk of electric shock at the Output lines when the UPS is ON.



Risk of electric shock at the Output lines while the unit is connected to the AC utility line.



Do not obstruct ventilation slots or holes and do not rest any object on top of the UPS.



Do not insert objects or pour liquids in the ventilation holes.



Install the UPS indoors, in a protected, clean and moisture-free environment.



Do not e pose to the direct sun light.



Do not keep liquids, flammable gases or corrosive substances near the UPS.

UPS EXA 1.1-1.5-2.2-2.6-3.2 3 User’s manual

1Introduction

EXA is a Line Interactive Pure Sinewave UPS (Uninterru tible Power Su ly) s ecifically designed to rotect your

com uter from any ty e of irregularities in the AC line (such as black-outs, under or over voltages, micro-

interru tions), which often cause damage to your Hardware and Software.

Under normal AC line condition, EXA erforms out ut voltage regulation and filters frequently occurring electrical

disturbances (such as transients, s ikes, interferences, etc.), thus rotecting all devices connected to the outlets,

and recharging the batteries in an ideal way. In case of anomaly to the AC line, the UPS continues feeding the

rotected equi ment.

EXA is equi ed with a RS-232 or USB interface which can be used to notify a ower failure or a low battery

condition directly to a com uter: this makes it ossible to automatically save your data during an extended black-

out with the most wides read o erating systems (Windows, Linux, etc.).

Read this manual carefully before using the EXA; it includes important safety warnings

and useful advices for correct use and installation.

This manual is a guide that enables you to correctly install and use your EXA. This

manual includes important SAFETY instructions for the operator, for the UPS correct

installation, and gives useful advice on the product and battery maintenance. For any

type of problem, please refer to this manual before calling the customer service.

EXA is constantly being develo ed and im roved: consequently, your unit may differ somewhat from the

descri tion contained in this manual.

This manual includes the following models:

•EXA 1.1 (1.1 KVA)

•EXA 1.5 (1.5 KVA)

•EXA 2.2 (2.2 KVA)

•EXA 2.6 (2.6 KVA)

•EXA 3.2 (3.2 KVA)

In this manual EXA will sim ly be referred to as UPS.

User’s manual 4 UPS EXA 1.1-1.5-2.2-2.6-3.2

2General Characteristics

EXA has all the advanced features, which guarantee maximum reliability and safety:

•All functions are controlled by a micro rocessor, giving full guarantee of high reliability.

•Out ut Voltage regulation through AVR (Automatic Voltage Regulation).

•Overload rotection both in normal mode and in battery mode.

•High erformance battery charger, which extends the battery medium life ensuring an o timal recharge.

•Start u even if the electrical network is not available.

•Automatic restart after an automatic shut down due to a low battery condition once the AC utility ower

returns.

•Ada ts automatically to 50 or 60 Hz in ut frequency.

•LCD dis lay for the visualization of the In ut and Out ut Voltage, Battery Level ercentage, Load Level

ercentage, functioning modes, alarm and fault conditions.

•Acoustic signals of various kinds indicating functioning modes and alarm/fault condition.

•Communication with the com uter through RS-232 and USB interfaces.

•SNMP Ada ter (o tional).

•Protects and filters the tele hone line.

•Fast swa able battery.

•High efficiency

•Maximum reliability

•Smart design and easy to use

3Receipt and site selection

Carefully remove the UPS from its ackaging, and carry out a meticulous ins ection. We recommend kee ing the

original ackaging in a secure lace, in case you need to send the UPS for maintenance ur oses. In case of

trans ort damage, notify the carrier and dealer immediately.

We recommend aying attention to the below oints in order to choose a correct lacement for your UPS:

•The UPS is designed to o erate in a rotected environment (e.g. offices). We therefore recommend

installing it in a lace with very little or no humidity, dust or smoke.

•In all circumstances, see the “Technical Characteristics” cha ter for environmental s ecifications and

check that the selected area meets these s ecifications.

•During normal o eration the UPS discharges a minimal amount of heat. So it is necessary to leave at least

20 cm of unobstructed s ace all around the UPS in order to kee it ro erly ventilated.

•Do not obstruct ventilation holes.

•Do not insert objects or our liquids in the ventilation holes.

•Do not rest any object on to of the UPS.

•Do not kee liquids, flammable gases or corrosive substances near the unit.

•Install the UPS on a ro erly tiled floor. Avoid the installation on a floor that is not tiled flat.

UPS EXA 1.1-1.5-2.2-2.6-3.2 5 User’s manual

4EXTERNAL DESCRIPTION

4.1 Front Panel

The front anel informs the user about o erating status, alarm conditions and measurements. Front anel shown

below consists of two arts:

1. LCD display rovides information about in ut (only in line mode) and out ut voltage, out ut frequency (only

in battery mode), battery level ercentage, load level ercentage, functioning modes, alarm and fault

conditions.

2. ON/OFF button: enables the user to turn ON/OFF the UPS.

Figure 1 – Front panel

User’s manual 6 UPS EXA 1.1-1.5-2.2-2.6-3.2

4.1.1 LCD Display

Please refer to figure 2.

Figure 2 –LCD Display

1. INPUT: the 3 digits indicate the in ut voltage (only visualized in line mode).

2. OUTPUT: the 3 digits indicate the out ut voltage.

3. BATTERY LEVEL: 3 digits indicate the battery charging ercentage.

4. LOAD LEVEL: 3 digits indicates the out ut load ercentage.

5. FREQUENCY: the 3 digits indicate the out ut frequency (only visualized in battery mode).

6. BUZZER: this icon indicate the UPS works in battery mode and acoustic alarm in on in the same time (only

visualized in battery mode).

Display visualizzato in modalità rete

Display visualizzato in modalità batteria

UPS EXA 1.1-1.5-2.2-2.6-3.2 7 User’s manual

4.2 Rear Side

Figure 2 – Rear Side

1. Grounded AC Input power socket: IEC C14 ty e; to connect the UPS to the AC utility line.

2. Input fuse: electrical s ecification: max current 6A (EXA 1.1–1.5), max current 8A (EXA 2.2) or max current

10A (EXA 2.6-3.2), voltage 250 V.

3. Grounded UPS Output receptacles: IEC C13 ty e, black colour, to su ly critical loads.

4. Grounded ONLY FILTERED Output receptacles (only for EXA 1.1-1.5-2.2): IEC C13 ty e, white colour, to

su ly NON-critical loads.

5. Telephone protection (RJ11 IN/OUT connectors): to rotect and filter a hone line (TNV-3 ty e

connections).

6. Computer Interface (DB9 female connector): it is the communication RS-232 ort.

7. Computer Interface (USB connector): it is the communication USB ort.

8. ON/OFF button: to active the AC utility line.

The 1 ONLY FILTERED Output receptacles (white colour, #4), protect only the devices

connected from overvoltages and disturbances of the AC line. Please connect ONLY the

NON-critical devices to the ONLY FILTERED Output receptacles

In case of anomaly to the AC line (black-out), ONLY the UPS Output receptacles (black

colour, #3) continue supplying the correct power to all connected equipment. Please

connect all the non-critical devices to the UPS Output receptacles.

EXA 1.1-1.5-2.2 EXA 2.6-3.2

User’s manual 8 UPS EXA 1.1-1.5-2.2-2.6-3.2

5Electrical Installation and First Start Up

We advise you to follow the ste s below ex lained for greater safety:

1. Switch off all the devices (Personal Com uter or other electronic devices) that need to be su lied by the

UPS.

2. Connect the UPS In ut socket to the AC line outlet Through the Personal Com uter su lying cable. It is

mandatory to ground the AC line outlet according to the Safety Standards. Carefully check the grounding,

make sure that the utility ower is available, and that its range falls within the UPS s ecifications (refer to

the “S ecifications” cha ter).

3. Switch ON the ON/OFF button on the rear anel and then ress the ON/OFF button on the front anel for 3

seconds: the UPS emits a brief acoustic signal, turns the LCD dis lay on, and erforms a functioning SELF-

TEST. Leave the UPS in Normal mode for at least 4 hours in order to com letely recharge the batteries.

4. Switch the UPS off (by ressing again the ON/OFF button for 3 seconds).

5. Connect the devices to be su lied to the UPS out uts, by using only the included cables. Be sure all the

devices have the main switch in ON osition.

6. Turn on the UPS again. Check that it starts working correctly and it doesn’t signal any sort of anomaly.

Moreover be sure that all the devices connected to the UPS out uts are working correctly. By LCD dis lay

check if the Out ut load ercentage is less than 100%; otherwise it is necessary to remove art of the Out ut

load.

7. Simulate a black-out by removing the AC In ut line. The UPS starts working in Battery mode. Moreover the

UPS emits a brief acoustic signal every 10 seconds.

8. Be sure that all the devices connected to the UPS out uts are working correctly and the UPS doesn’t signal

any sort of anomaly.

9. Restore the AC In ut line: after few seconds the UPS turns back in Normal mode.

Before using EXA normally, leave it in Normal mode in order to charge the batteries com letely as s ecified at

oint 3. The batteries reach the 90% of their ca acity after about 4 hours of recharge.

It is compulsory to ground/earth the UPS according to the Safety Standards.

Risk of electric shock at the Output lines if the UPS is ON, even when the UPS is not

connected to AC utility line.

Risk of electric shock at the Output lines while the unit is connected to the AC utility

line.

Risk of electric shock: do not remove the cover. The UPS contains internal parts, which

are at a high Voltage and are potentially dangerous, capable of causing injury or death

by electric shock.

There are no internal parts in the UPS that are user serviceable. Any repair or

maintenance work must be performed e clusively by qualified technical personnel

authorized by TECNOWARE. TECNOWARE declines any responsibility if this warning is

disregarded.

Disregard for these warnings may lead to a risk of electric shock to operators.

Autres manuels Tecnoware UPS

Tecnoware

Tecnoware ERA PLUS 1600 SCHUKO Manuel utilisateur

Tecnoware

Tecnoware EVO DSP MM 3.6 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 2.0 - pf 0,9 Manuel utilisateur

Tecnoware

Tecnoware V33/65-80-100 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP TM Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS TT 10.0 Manuel utilisateur

Tecnoware

Tecnoware ATA 4.0 MM Manuel utilisateur

Tecnoware

Tecnoware ERA PLUS 600 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS 1.200 Rack Tower PF 0.9 Manuel utilisateur

Tecnoware

Tecnoware EXA PLUS Manuel utilisateur

Tecnoware

Tecnoware EVO DSP MM 4.0 Rack Tower Manuel utilisateur

Tecnoware

Tecnoware ERA PLUS 900 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS 1.200 PF 0.9 Manuel utilisateur

Tecnoware

Tecnoware UPS EVO DSP PLUS 6.5 PF 0,9 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 1.2 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur

Tecnoware

Tecnoware EXA 1.1 Manuel utilisateur

Tecnoware

Tecnoware ECO STRIP 0.50 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 1.0 - pf 0,9 Manuel utilisateur

Tecnoware

Tecnoware ERA PLUS 1.100 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP TT Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS 800 PF 0.9 Manuel utilisateur

Tecnoware

Tecnoware EVO TM 15.0 Manuel utilisateur

Tecnoware

Tecnoware UPS EVO DSP PLUS 1.0 MM Manuel utilisateur

Manuels UPS populaires d'autres marques

Pylontech

Pylontech Victron & Pylontech US5000 Manuel utilisateur

Mecer

Mecer ME-1000-WTU Manuel utilisateur

Mustek

Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation

Emerson

Emerson Liebert NXL series Manuel utilisateur

MAKELSAN

MAKELSAN BOXER SERIES Manuel utilisateur

Block

Block PC-0524-400-0 Manuel utilisateur

CyberPower

CyberPower CP585LCD Manuel utilisateur

Eaton

Eaton 3S Instructions de montage

CyberPower

CyberPower Office Tower Series UPS 1000 Manuel utilisateur

CyberPower

CyberPower BM100 Manuel utilisateur

Best Power

Best Power 610 Manuel utilisateur

Best Power

Best Power Unity/I UT3K Manuel utilisateur

Mustek

Mustek PowerMust 400 Offline Manuel utilisateur

Xantrex

Xantrex Trace 512 UR-UPS Manuel utilisateur

Forza

Forza SL-1501UL Manuel utilisateur

LEGRAND

LEGRAND keor 310081 Manuel utilisateur

ABB

ABB Conceptpower DPA 500 Manuel utilisateur

ZincFive

ZincFive BC Series Manuel utilisateur