Tecnoware EVO 3.0 RT Manuel utilisateur

EVO RT

Uninterruptible Power Supply

EVO 1.0 RT

EVO 2.0 RT

EVO 3.0 RT

USER’S MANUAL

11 INDEX

SECURITY NOTICE page 2

INTRODUCTION page 3

EVO RT UPS

1 MAIN CHARACTERISTICS page 4

2 EXTERNAL DESCRIPTION page 5

FRONT PANEL

REAR SIDE

EPO (EMERGENCY POWER OFF)

REMOTE ON/OFF

DRY CONTACTS BOARD

3 RUNNING OPERATIONS page 8

SWITCHING ON

LINE MODE

BATTERY MODE

BYPASS MODE

LOW BATTERY AND AUTOMATIC RESTART

LOAD TEST

4 INSTALLATION INSTRUCTIONS page 11

RECEIPT OF UPS

PLACEMENT

FIRST START UP

5 COMPUTER INTERFACE page 12

6 TECHNICAL CHARACTERISTICS page 13

7 SUGGESTIONS FOR A CORRECT USE page 14

MAINTENANCE

BATTERY MAINTENANCE

BATTERY REPLACEMENT (HOT SWAP BATTERIES)

SAFETY FOR THE OPERATOR

8 ANOMALIES AND TROUBLESHOOTING page 16

9 FIGURES page 17

All trademark are property of their respective owners.

TECNOWARE s.r.l.

www.service.tecnoware.com

This manual has been printed and edited by TECNOWARE s.r.l.

November 2006 Edition version 3.0

User’s manual 1UPS EVO RT

11 SECURITY NOTICE

Read this manual carefully before installing and using TECNOWARE EVO RT

Uninterruptible Power Supply, which will be referred to as UPS from

hereafter.

The UPS must be used only by properly trained personnel. To ensure correct

and safe operation, it is necessary that operators and maintenance

personnel observe the general Safety Standards as well as the specific

instructions included in this manual.

Risk of electric shock: do not remove the cover. The UPS contains internal

parts which are at a high voltage and are potentially dangerous, capable of

causing injury or death by electric shock.

There are no internal parts in the UPS that can be repaired by the user. Any

repair or maintenance must be performed exclusively by qualified technical

personnel authorized by TECNOWARE.

TECNOWARE declines any responsibility if this warning is disregarded.

It is compulsory to ground the UPS according to Safety Standards.

Risk of electric shock at the output socket when the UPS is ON.

Risk of electric shock at the output socket while the unit is connected to the

AC utility line.

Use the input power cable given with the unit and connect it to the AC utility

line. In all circumstances a (H05VVF3G 1,5mm²) cable or a better one must

be used.

Do not obstruct ventilation slots or holes and do not place any object on top

of UPS.

Do not insert objects or pour liquids in the ventilation holes.

Do not keep liquids, flammable gases or corrosive substances near the UPS.

Install the UPS indoors, in a protected, clean and moisture-free

environment.

UPS EVO RT 2User’s manual

11 INTRODUCTION

EVO RT UPS

EVO RT UPS (Uninterruptible Power Supplies) are the result of constant technological research

aimed at obtaining the best performance at the lowest cost.

EVO RT UPS are advanced ON-LINE UPS, single-phase, built specifically to protect your

computer from any irregularities in the AC line (for example blackouts, brownouts,

overvoltages, micro-interruptions) which often cause damage to hardware and software.

During a power failure, EVO RT continues supplying adequate AC power (with a true sinewave)

to all connected devices from the internal battery and by the DC/AC converter (Inverter).

Under normal AC line condition, EVO RT provides an automatic output voltage regulation from

the Rectifier and Inverter boards,and, filters out frequently occurring electrical disturbances

(high voltage transients, spikes, interferences, etc.), thus protecting all connected devices.

EVO RT protects all connected devices from accidental overload or Inverter fault through an

AUTOMATIC BYPASS that directly connects the AC input line with its outlets.

EVO RT is supplied with an RS-232 communication port and USB port, which can be used to

signal to a generic processor or computer the absence of mains supply or the end of battery

autonomy. This permits to carry out an automatic data saving operation during a long black out

with the most spread Operating Systems (Windows, Linux, Novell, etc).

Furthermore, the communication ports permit EVO RT to communicate with the computer,

transferring various measurements such as: input output voltage, battery voltage, output

power, frequency, and it can also be programmed for automatic operations such as switching

ON/OFF at a preset time.

WARNING

Please read this manual before using EVO RT. It contains important safety

information for the operator that will guide him to a correct use of the unit.

This manual is related to the below EVO RT models:

•EV0 1.0 RT

•EV0 2.0 RT

•EV0 3.0 RT

In this manual EVO RT will simply be called UPS.

EVO RT is in 19” RACK version (RT = Rack & Tower), it means that its sizes are compatible with

19” RACK cabinets and it has been designed to be included in the 19” RACK cabinets

EVO can even be used in TOWER position that is a vertical one, thanks to the relative and

reliable pedestals

EVO RT is constantly being developed and improved: consequently, your unit may differ

somewhat from the description contained in this manual.

In this manual EVO RT will simply be called UPS.

User’s manual 3UPS EVO RT

11MAIN CHARACTERISTICS

EVO RT offers all the modern characteristics which guarantee maximum reliability and security:

•Microprocessor control guarantees high reliability

•ON-LINE double technology without transformer

•Pure Sinewave

•Output voltage regulation +/- 2%

•Overload, overheating and short circuit protection

•AUTOMATIC BYPASS to protect from accidental overload or Inverter fault

•MANUAL BYPASS through switch on the rear side

•Switching ON even with no mains condition (Black start capability)

•Automatic protection in case of discharged batteries

•After a shutdown caused by the end of autonomy and when mains condition is restored there

is an automatic SWITCHING On operation

•Automatic functioning test through a switch

•Automatic regulation to the input frequency 50 or 60 Hz

•Visual warnings by leds, indicating operational mode and low battery, overload and alarm

conditions

•Dry contacts board (Optional)

•SNMP Adapter (Optional)

•EPO (Emergency Power OFF)

•Remote ON/OFF

•Acoustic signals of various kinds indicating alarm situations

•Communication with the computer by a RS-232 Interface and possible monitoring of

input/output voltage, frequency, output power, battery voltage, etc.

•Automatic turn on/off user-programmable by RS-232 Interface

•Protection filter for the telephone, ADSL and data line

•Possibility to increase the autonomy through External Battery boxes (optional)

•HOT SWAP BATTERY

•Sizes compatible with 19” RACK cabinets

•Can be used in TOWER position that is a vertical one, thanks to the provided pedestals

•High reliability and high performances

•Easy to use

UPS EVO RT 4User’s manual

12EXTERNAL DESCRIPTION

FRONT PANEL

The control buttons and leds indicating various operating modes and alarm conditions are

situated on the front panel. Please see the figures 1 and 2.

OFF button

To turn the UPS OFF, press this button for 3 seconds.

ON/TEST/ALARM button

Can be used for 3 functions:

•SWITCHING ON: the UPS is switched on by keeping the button continuously pressed for 3

seconds.

•SELF-TEST: the UPS performs a SELF-TEST, according to the procedure explained further on,

and when the button is pressed during LINE mode for 3 seconds.

•ALARM OFF: during BATTERY mode, press this button for 3 seconds to disable the alarm

buzzer

LINE led

This (blue) led is ON when the input AC line voltage amplitude is within the specification, and it

indicates the UPS is working in LINE mode.

If LINE led flashes every second it means that the Phase line and Neutral line of AC input utility

line are inverted. In such case the AC power input plug must be disconnected. Turn it at 180

degrees and connect the power plug again.

INVERTER led

This (blue) led is on when the Inverter is operating normally

BATTERY led

This (blue) led is on when the UPS is working on BATTERY mode (during a blackout or

overvoltage/brownout).

BYPASS led

This (blue) led is on when the UPS is working in BYPASS mode: the AC input line is connected

directly to the UPS outlets.

FAULT led

This (red) led is turned on whenever the UPS detects a FAULT condition and needs a technical

intervention as soon as possible.

User’s manual 5UPS EVO RT

LOAD LEVEL led bar

Refer Figure 2

The led bar has 6 leds (5 leds are blue and one led is red). This bar indicates the output power

percentage (LOAD LEVEL), proportional to the number of switched on leds.

The greater the load the more LED indicators will light on.

There are the following LOAD LEVEL percentages:

•0~20%: only one led is on (Led13)

•21~40%: two leds are on (Led13 and Led12)

•41~60%: three leds are on (Led13, 12 and 11)

•61~80%: four leds are on (Led13, 12, 11 and 10)

•81~100%: five leds are on (Led13, 12, 11, 10 and 9)

The OVERLOAD red led (Led8), is on to warn of an OVERLOAD condition.

BAT. LEVEL led bar

Refer Figure 2

The led bar has 6 leds (5 leds are blue and one is yellow). This bar indicates the battery

capacity percentage (BAT. LEVEL), proportional to the number of switched on leds.

The higher the battery capacity the more LED indicators will light on.

There are the following battery capacity percentages:

•100~81%: five leds are on (Led15, 16, 17, 18 and 19)

•80~61%: four leds are on (Led15, 16, 17 and 18)

•60~41%: three leds are on (Led15, 16 and 17)

•40~21%: two leds are on (Led15 and Led16)

•20~0%: only one led is on (Led15)

The LOW BAT yellow led (Led14), is on to warn of a LOW BATTERY condition during BATTERY

mode.

REAR SIDE

The following are located on the rear side (see figure 3):

1) Grounded AC Input power socket: to connect the UPS to AC utility line by the supplied

input cord.

2) Input Circuit Breaker: it goes off in overload or short-circuit condition; push the external

3) Grounded output socket: for connecting equipments to be protected.

4) (Only EVO 2.0 and EVO 3.0) Grounded power output socket: for connecting an

output power line to supply all the equipments to be protected.

5) RS-232 Computer Interface (female connector 9 poles DB9): it is the interface port

(RS-232) to communicate with a computer.

6) RJ11/RJ45 IN/OUT plugs: to protect and filter a phone line, an ADSL or a LAN.

7) External batteries connector: to connect the UPS to an external Box Battery (optional).

8) Slot for Dry contact board / Slot for SNMP adapter (optional).

9) Manual BYPASS switch: to force the UPS into BYPASS mode (see chapter “Running

Operations”).

10) Remote ON/OFF contact.

11) EPO (Emergency Power OFF).

UPS EVO RT 6User’s manual

EPO (EMERGENCY POWER OFF)

EPO

Remote Button

EPO

EVO have the EPO (Emergency Power OFF) connector (2 terminals connector) on the rear. This

permits to immediately switch the UPS OFF from a distance in case of emergency.

To use EPO function is very simple: it is sufficient to connect an external switch to the EPO

terminal(see Figure 3 – Rear Side): if the switch is CLOSED the UPS works normally. If on the

contrary, the switch is OPEN then the UPS turns OFF immediately. To switch ON the UPS again

it is necessary to close the EPO switch and then manually restart the UPS from the front panel.

The EPO terminals are isolated and do not need an external feeding voltage.

REMOTE ON/OFF

Remote Button ON

OFF

Remote Button OFF

The EVO models have remote ON/OFF terminals connector on the rear side (see figure 4),

this permits to switch the UPS ON and OFF from a distance. Using the ON/OFF external

button (as described in the above picture) the frontal panel button capacity can be used

from a distance.

Evo is on; pressing the OFF button connected to terminal 1 and 2 for at least 3 seconds,

EVO turns OFF.

EVO is off; pressing the ON button connected to terminal 4 and 5 for at least 3 seconds,

EVO turns ON.

The remote ON function is disabled when the UPS is off and the AC input line voltage is not

present.

User’s manual 7UPS EVO RT

DRY CONTACTS BOARD (OPTIONAL)

Common

Fault

Bypass

56AC fail

Low BAT

910

The Dry Contact Board is constituted by a 10 pin connector.

1. Common

Pin 1 and Pin 2 are common pins.

2. Fault

Pin 3 is the normal-open output: When UPS works normally, Pin 3 and Pin 1-2 will be

open, when UPS is failed, Pin 3 and Pin 1-2 will be closed.

Pin 4 is normal-closed output: When UPS works normally, Pin 4 and Pin 1-2 will be

closed, when is failed, Pin 4 and Pin 1-2 will be open.

3. Bypass

Pin 5 is the normal-open output: When UPS works normally, Pin 5 and Pin 1-2 will be

open, when UPS works in bypass mode, Pin 5 and Pin 1-2 will be closed.

Pin 6 is normal-closed output: When UPS works normally, Pin 6 and Pin 1-2 will be

closed, when UPS works in bypass mode, Pin 6 and Pin 1-2 will be open.

4. AC fail

Pin 7 is the normal-open output: When UPS works normally, Pin 7 and Pin 1-2 will be

open, when UPS works in AC failure mode, Pin 7 and Pin 1-2 will be closed.

Pin 8 is normal-closed output: When UPS works normally, Pin 8 and Pin 1-2 will be

closed, when UPS works in AC failure mode, Pin 8 and Pin 1-2 will be open.

5. Low Bat

Pin 9 is the normal-open output: When UPS works normally, Pin 9 and Pin 1-2 will be

open, when UPS works in battery low voltage mode, Pin 9 and Pin 1-2 will be closed.

Pin 10 is normal-closed output: When UPS works normally, Pin 10 and Pin 1-2 will be

closed, when UPS works in battery low voltage mode, Pin 10 and Pin 1-2 will be open.

UPS EVO RT 8User’s manual

Autres manuels pour EVO 3.0 RT

Table des matières

Autres manuels Tecnoware UPS

Tecnoware

Tecnoware ERA PLUS 800 SCHUKO Manuel utilisateur

Tecnoware

Tecnoware EVO DSP MM 6.0 Manuel utilisateur

Tecnoware

Tecnoware EXA PLUS 1000 Manuel utilisateur

Tecnoware

Tecnoware ERA PLUS 900 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MODULAR Manuel utilisateur

Tecnoware

Tecnoware EVO DSP TT Manuel utilisateur

Tecnoware

Tecnoware EVO STAR Manuel utilisateur

Tecnoware

Tecnoware ERA PLUS 750 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 2.0 - pf 0,9 Manuel utilisateur

Tecnoware

Tecnoware EXA 2.6 Manuel utilisateur

Tecnoware

Tecnoware EASY Power 900 Manuel utilisateur

Tecnoware

Tecnoware ERA PLUS 600 Manuel utilisateur

Tecnoware

Tecnoware EXA PLUS Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS 1.200 PF 0.9 Manuel utilisateur

Tecnoware

Tecnoware ERA LED 0.85 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS 800 PF 0.9 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS TM 10 KVA Manuel utilisateur

Tecnoware

Tecnoware Ups Pro Manuel utilisateur

Tecnoware

Tecnoware EXA PLUS 1.0 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS TT 10.0 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP TM Manuel utilisateur

Tecnoware

Tecnoware ERA PLUS 1.100 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP MM 3.6 Manuel utilisateur

Manuels UPS populaires d'autres marques

Pylontech

Pylontech Victron & Pylontech US5000 Manuel utilisateur

Mecer

Mecer ME-1000-WTU Manuel utilisateur

Mustek

Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation

Emerson

Emerson Liebert NXL series Manuel utilisateur

MAKELSAN

MAKELSAN BOXER SERIES Manuel utilisateur

Block

Block PC-0524-400-0 Manuel utilisateur

CyberPower

CyberPower CP585LCD Manuel utilisateur

Eaton

Eaton 3S Instructions de montage

CyberPower

CyberPower Office Tower Series UPS 1000 Manuel utilisateur

CyberPower

CyberPower BM100 Manuel utilisateur

Best Power

Best Power 610 Manuel utilisateur

Best Power

Best Power Unity/I UT3K Manuel utilisateur

Mustek

Mustek PowerMust 400 Offline Manuel utilisateur

Xantrex

Xantrex Trace 512 UR-UPS Manuel utilisateur

Forza

Forza SL-1501UL Manuel utilisateur

LEGRAND

LEGRAND keor 310081 Manuel utilisateur

ABB

ABB Conceptpower DPA 500 Manuel utilisateur

ZincFive

ZincFive BC Series Manuel utilisateur