Technoline WS-6010 Manuel utilisateur

Battery

compartment

Wall Mount

Location

LCD

display

Stand

Solar

panel

SOLAR STATION

INSTRUCTION MANUAL

FEATURES:

SOLAR STATION:

•

24h time format display

•

Solar mode setting

•

Indoor and outdoor temperature display in ºC with MIN/MAX records

•

Indoor and outdoor humidity display in RH%

•

Primary Alkaline battery or rechargeable Alkaline battery selection

•

Low battery indicators

•

Wall mount or freestanding

Function

keys

SOLAR-POWERED TRANSMITTER:

•Remote transmission of outdoor temperature and

humidity to the Solar Station by 868 MHz signals

•LCD will automatically alternate and display the

outdoor temperature and humidity data

•Recharge batteries by solar-powered cells

•

Wall mounting case

Note:

•

The solar-powered transmitter uses solar cells to charge the rechargeable

batteries (2 x AAA rechargeable batteries).

•

Those rechargeable batteries cannot be replaced.

SOLAR TRANSMITTER OPERATION MODES

Important:

Users need to press the reset key to activate the solar transmitter and link

the transmission to the Solar Station (receiver).

It is important to allow sufficient light to reach the solar panel while activating the

solar transmitter. Make sure the lights are on in the setup room and the solar

panel is facing a 60W light bulb or brighter - do not cover with hands or other

objects.

SOLAR TRANSMITTER RESET KEY:

The solar transmitter has 3 operations modes:

RESET key

Note: only use a small pointed pen to

press the RESET key to re-active the

transmitter into Normal Operation Mode.

Solar panel

Normal Operation Mode:

•

This mode occurs when the battery voltage is higher than 2.5V.

•

The transmitter will measure and transmit the temperature and humidity

data to the Solar Station every 5 seconds.

•

If a dark environment is detected, it will measure and transmit the

temperature every 10s.

•

If the battery voltage is dropped lower than 2.8V, it will measure and

transmit the temperature every 10s

•

If battery voltage is dropped lower than 2.4V, will go into Idle mode.

•

If the solar transmitter is placed into a dark environment for 72 hours, will

goes into Stop mode.

•

If the user cover the solar cell for 10 seconds and press the reset button,

"StP" will be displayed on the LCD. Then the transmitter enters STOP

mode.

Idle Operation Mode:

•

This mode is occurred when the battery voltage is dropped lower than

2.4V

•

LCD is turned off

•

Does not perform temperature measurement and transmission

•

If battery voltage is raised higher than 2.5V, will go into Normal mode

•

If the solar transmitter is placed into a dark environment for 72 hours, will

goes into Stop mode.

Stop Operation Mode:

•

This mode is occurred when the solar transmitter is placed into a dark

environment for 72 hours or the user cover the solar cell for 10 seconds

and press the RESET button

•

The transmitter is in a standby state. Without perform any operation and

LCD is off

•

Under a bright condition, press the reset button to wake up the transmitter

into normal operation mode (battery voltage is higher than 2.5V). ). If the

battery is lower than 2.4V, a “Lo” icon will be shown in the LCD for a while.

Then the transmitter will enter the idle mode.

•

The most power saving mode.

INITIAL SETUP

It is very important to follow these steps:

Open the battery compartment, and make sure that the battery switch is

in the BATTERY position (not the SOLAR position).

Battery switch in the BATTERY position

3. Now locate the battery insulator tab, and gently pull to remove it.

4. Slide the battery switch to the SOLAR position

5. Battery switch in the SOLAR position

Continue to section titled “Setup After Changing/Installing the

Batteries”

TO INSTALL / REPLACE BATTERY IN THE SOLAR STATION

The Solar Station can use either the included 2 x Alkaline rechargeable

batteries (charged by solar panel) or 2 x AA Alkaline batteries (non-

rechargeable; not included).

Important: the battery type selection (rechargeable or non-rechargeable)

must be made BEFORE inserting the battery into the compartment

otherwise it may cause damage to the station!

The included Alkaline rechargeable batteries should provide you with many

years of service.

If you choose to use non-rechargeable batteries, the battery switch MUST be

moved to the BATTERY position (not the SOLAR position). In this position, the

solar cells do not charge the batteries.

REGARDLESS OF THE TYPE OF BATTERY INSTALLED, THE BATTERY

SWITCH MUST BE IN THE BATTERY POSITION WHEN THE BATTERY IS

INSERTED.

If rechargeable batteries are used, the Battery switch should be moved to the

SOLAR position AFTER they have been inserted.

To use the included rechargeable Alkaline batteries (charged by solar

panel):

1. Remove the insulation tape.

2. Replace battery cover

3. Remove the black protective foil on the solar panel.

DO NOT SET THE CLOCK.

Battery cover

To use non-rechargeable Alkaline batteries:

1. Remove the included rechargeable AA batteries from the compartment.

2. Use the switch to select the Alkaline battery (see below).

3. Insert 2 x AA Alkaline batteries into the compartment, observing the

correct polarity (see marking inside battery compartment.)

4. Replace battery cover

DO NOT SET THE CLOCK.

Note: For best performance, batteries should be replaced at least once every 2

years to maintain the best running accuracy. Ensure that the batteries used are

new and the correct size.

Please help in the preservation of the environment and return

used batteries to an authorized depot.

Use switch

to select

which type of battery will

be used before inserting

the battery into the

compartment

Rechargeable Alkaline

battery switch position

Primary Alkaline

battery switch position

SETUP AFTER CHANGING/REPLACING THE BATTERIES IN THE

SOLAR STATION

1. First, press the reset button on the Solar Transmitter. All segments of the

LCD will light up briefly. The code number and the security code (for

example, “20”) will be displayed sequentially. Next, the batteries voltage

will be shown on the LCD, it should be higher than 2.4V in order to

maintain the normal operation. The current temperature/humidity will be

display on the transmitter, and the transmitter starts the transmission of

signal.

2. Within 2 minutes of the start up of transmitter, insert the batteries to the

Solar Station. Once the batteries of the Solar Station are in place, all

segments of the Solar Station’s LCD will light up briefly and the time

(00:00), date, indoor temperature will be displayed on the Solar Station. If

they are not shown in the LCD after 30 seconds, reinstall the batteries of

the Solar Station again. Once the indoor data is displayed, the Solar

Station will start receiving the outdoor data.

3. The outdoor temperature and humidity data should then be displayed on

the Solar Station. If this does not happen after 2 minutes, the batteries will

need to be removed from the display and reset from step 1.

4. In order to ensure better reception and transmission, the distance

between the Solar Station and the transmitter should not be more than

100m to ensure sufficient 868 MHz transmission. (see notes on

“Positioning” and “868 MHz Reception”).

Note: When changing the batteries:

1. Be careful that they do not spring free from the contacts.

2. Press any button 20 times with the batteries removed.

3. Always wait at least 10 minutes after removing batteries before re-

inserting; otherwise start up problems may occur.

FUNCTION KEYS

The solar station has 2 easy to use keys:

SET key : To enter into the set modes for: time and solar modes

To toggle between the display modes

Low battery icon (transmitter)

Indoor

temperature

Low battery icon (station)

Outdoor

temperature

+key : To change any values in manual set modes

To reset all the MIN/MAX temperature records to current

temperatures

LCD SCREEN DESCRIPTIONS

The solar station LCD is divided into 2 sections and once the batteries are

inserted, all the segments will light up briefly before displaying the information

for time, indoor and outdoor temperature and indoor and outdoor humidity.

*When the signal from the transmitter is successfully received by the Solar

Station, this icon will be switched on. (If not successful, the icon will not be

shown on the LCD). User can therefore easily see whether the last reception

was successful (“ON” icon) or not (“OFF” icon). On the other hand, the short

blinking of the icon shows that a reception is being done at that time.

LOW BATTERY INDICATOR:

-RX Low battery indicator is displayed on the LCD when the Solar Station

batteries voltage is low.

-TX Low battery indicator is displayed on the LCD when the Solar Transmitter

batteries voltage is low.

Outdoor

humidity

display

Indoor humidity

display

Time

Outdoor

transmission

reception icon*

MANUAL SETTINGS

After completion of the above described procedures in “Setting-up” the manual

setting modes can be entered by pressing the SET key. The following settings

can now be programmed:

•

Manual time setting

•

Solar mode setting

MANUAL TIME SETTING

1. Press and hold the SET key for 3 seconds to enter the time setting mode.

2. The hour digits start flashing.

3. Set the desired hours by pressing and releasing the +key followed by

pressing the SET key.

4. Now the minute digits start flashing.

5. Set the desired minutes by pressing and releasing the +key. If the +key

is held, the units will increase by 5.

6. Press the SET key again to confirm and enter the Solar Mode setting.

SOLAR MODE

The Solar Mode is used for saving the power consumption of the rechargeable

battery (Default setting ON):

1. The characters “ON” or “OFF” will start flashing. By use of the +key

select “ON” or “OFF” to set the solar mode.

2. Press and release the SET key to exit the setting mode and switch back to

the normal display mode.

If the solar mode setting is ON:

•

LCD will automatically turn OFF if the environment is too dark

•

LCD will automatically turn ON if the environment is bright enough; the

surrounding environment brightness is checked every 5 seconds.

•

No information will be displayed when the LCD is OFF, but all the

settings and operations will remain, except for the temperature and

humidity measurements.

•

The outdoor data will not be received if the LCD is OFF for more than

10 minutes.

•

If the user wants to check data while the display is automatically turned

off, because the environment is not bright enough, take the solar

station into a brighter environment. The display will turn on again.

If the solar mode setting is OFF:

•

LCD will remain ON constantly.

•

All outdoor data reception and measurements will be performed even if

a dark environment is detected.

STOP MODE

If the Solar Station is placed in a dark environment for 72 hours continually, the

solar station will go to the stop mode:

•

The most power saving condition.

•

The Solar Station will not perform any operation and the LCD will also be

OFF.

•

Users need to press any key to wake up the Solar Station and to re-

activate the transmission with the solar transmitter.

EXIT THE MANUAL SETTING MODES

If no keys are pressed for at least 15 seconds in setting mode, the solar station

will automatically switch back to normal display mode.

TO VIEW THE INDOOR AND OUTDOOR MIN/MAX

TEMPERATURES

1. From normal display, press the +key once to view the MIN/MAX outdoor

temperature.

2. Press the +key again to view the MIN/MAX indoor temperature.

3. Press the +key a third time to return to normal display.

Note:

•

The resolution for the MIN/MAX temperature records is 0.5ºC

•

If no keys are pressed for 15 seconds, the Solar Station will automatically

switch back to normal display.

TO RESET THE MIN/MAX TEMPERATURE RECORDS:

Press and hold the + key for 3 seconds to reset the MIN/MAX temperature

records. This will reset all the indoor and outdoor MIN/MAX records to current

temperatures.

CHANGING THE DISPLAY MODE

The Solar Station can be set to show different displays:

1. From normal display, press the SET key:

2. Press the SET key again

3. Press the SET key again and the display will return to the normal display

868MHZ RECEPTION CHECK FOR OUTDOOR SOLAR

TRANSMITTER

The Solar Station will receive the outdoor data every 50 seconds. If the

temperature data is not being received 2 minutes after setting up (or the display

shows “- - -”), then please check the following points:

1. The distance of the Solar Station or outdoor transmitter should be at least

2 meters away from any interfering sources such as computer monitors or

TV sets.

2. Avoid placing the receiver onto or in the immediate proximity of metal

window frames.

The LCD1 will now display:

outdoor temperature/ outdoor

humidity

The LCD1 will display:

indoor

temperature/ indoor humidity

Table des matières

Autres manuels Technoline Station météorologique

Technoline

Technoline WS 6830 Manuel utilisateur

Technoline

Technoline WD 2000 Manuel utilisateur

Technoline

Technoline WS6462 Manuel utilisateur

Technoline

Technoline WS 9120 Manuel utilisateur

Technoline

Technoline WT 171 Manuel utilisateur

Technoline

Technoline WS 9040 Manuel utilisateur

Technoline

Technoline WS 6600 Manuel utilisateur

Technoline

Technoline WS 6830 Manuel utilisateur

Technoline

Technoline WS 6760 Manuel utilisateur

Technoline

Technoline WS 6720 Manuel utilisateur

Technoline

Technoline WS 6820 Manuel utilisateur

Technoline

Technoline WS6501 Manuel utilisateur

Technoline

Technoline WS 6870 Manuel utilisateur

Technoline

Technoline WS9050 Manuel utilisateur

Technoline

Technoline WS 6715 Manuel utilisateur

Technoline

Technoline WS 9257 Manuel utilisateur

Technoline

Technoline WS6850 Manuel utilisateur

Technoline

Technoline WS7073 Manuel utilisateur

Technoline

Technoline WS 9422 Manuel utilisateur

Technoline

Technoline WS9251 Instructions d'installation

Technoline

Technoline WS 9274 Manuel utilisateur

Technoline

Technoline WS 6730 Manuel utilisateur

Technoline

Technoline WS 8005 Manuel utilisateur

Technoline

Technoline WS 9130 Manuel utilisateur

Manuels Station météorologique populaires d'autres marques

Auriol

Auriol AHFL 433 A1 Manuel utilisateur

NexSens

NexSens G2-HYDROMET Manuel utilisateur

Hyundai

Hyundai WS 2202 Manuel utilisateur

IROX

IROX HBVR761 UV-X Manuel utilisateur

La Crosse Technology

La Crosse Technology C86371 Manuel utilisateur

ADE

ADE WS 1711 Manuel utilisateur

Auriol

Auriol z29592 Manuel utilisateur

Auriol

Auriol 296289 Manuel utilisateur

Hyundai

Hyundai WS 2266 Manuel utilisateur

La Crosse Technology

La Crosse Technology WS-2210 Manuel utilisateur

La Crosse Technology

La Crosse Technology WS-811561 Manuel utilisateur

Ventus

Ventus W177 Manuel utilisateur

National Geographic

National Geographic VA Colour RC Manuel utilisateur

Renkforce

Renkforce 1208067 Manuel utilisateur

Levenhuk

Levenhuk Discovery Report WA40 Manuel utilisateur

Instant Transmission

Instant Transmission MA 10410 Manuel utilisateur

Lutron Electronics

Lutron Electronics PHB-318 Manuel utilisateur

WAREMA

WAREMA EWFS Weather station eco Manuel utilisateur