NexSens G2-HYDROMET Manuel utilisateur

G2-HYDROMET Quick Start

For best results, setup your new product in the office/lab. Collect a few

data points and become familiar with the system prior to field deployment.

1Go to V2.WQDataLIVE.com/Getting-Started

2Create a new account or sign into an existing

account and enter the Claim Code found on

the serial label to access the device’s data

3Place the HYDROMET in an area with strong

cellular coverage and connect the antenna

4Connect the Solar Pack’s UW-6 to the

HYDROMET’s UW-6 pigtail to power the device

(device will beep once when powered)

5Refresh WQData LIVE and confirm the Diagnostic

Data Last Contact timestamp has been updated

(May take up to 1 minute*)

6Deploy the device by screwing it onto a

leveled 2” NPT pole and orienting it

north using the Airmar alignment mark

7Angle the solar panel by removing the

outter angle adjustment bolt with the

included 3/16” hex wrench, tilting to the

desired angle (30° or 45°), and replacing the bolt

Connect Optional Hydrological Sensor

8Connect the Hydrological sensor to the UW-8 pigtail

9On WQData, click the G2-HYDROMET’s icon in the

righthand Site List panel to access the Remote Device

Configuration dialog and queue a Detect Sensors and Sensor

Read command (check the boxes and click SAVE)

10 Cycle power (UW-6 pigtail) to

execute the remote command

11 Confirm the new parameters

are online (May take up to 3

minutes for detection and

upload)

Serial Label

Troubleshooting

Symptom

Possible Cause

Corrective Action

Claim code

does not work

Code was entered

incorrectly

Re-enter code exactly as shown on the

serial label

Device was

already claimed

Check with previous owners/users

WQData LIVE’s

Last Contact

time does not

update

Device does

not upload

new data to

WQData LIVE

No power to

device

Confirm the UW-6 is connected

Cycle power by disconnecting and

reconnecting the UW-6 solar pack plug

and listening for a beep

Replace the battery in the SP6

No cellular

coverage

Install the right angle adapter to point

the antenna sideways instead of down

Relocate the unit to an area with

strong cellular coverage and no

obstructions (outside in a parking lot

is typically good), then cycle the power

(disconnect and reconnect the UW-6).

The device should beep twice after

being powered for 30-60 seconds.

Three beeps indicates no signal.

Meteorological

or Hydrology

data reports

errors

Battery voltage

below 9V

Repair/Replace the battery pack

Sensor damaged

Visually inspect sensor and contact

NexSens for RMA authorization

Hydrology data

reports errors

Sensor

disconnected or

cable damaged

Visually inspect cable for cuts and

check connection is secure and dry

Sensor not

functional

Connect to the sensor directly and

confirm communication

*A brand new modem may require up to 2 minutes to provision with the

cellular provider the first time it connects to the internet.

For more assistance visit:

www.NexSens.com/Category/Knowledge-Base/G2-Series-Monitoring

Manuels Station météorologique populaires d'autres marques

Auriol

Auriol AHFL 433 A1 Manuel utilisateur

Hyundai

Hyundai WS 2202 Manuel utilisateur

IROX

IROX HBVR761 UV-X Manuel utilisateur

La Crosse Technology

La Crosse Technology C86371 Manuel utilisateur

ADE

ADE WS 1711 Manuel utilisateur

Auriol

Auriol z29592 Manuel utilisateur

Auriol

Auriol 296289 Manuel utilisateur

Hyundai

Hyundai WS 2266 Manuel utilisateur

La Crosse Technology

La Crosse Technology WS-2210 Manuel utilisateur

La Crosse Technology

La Crosse Technology WS-811561 Manuel utilisateur

Ventus

Ventus W177 Manuel utilisateur

National Geographic

National Geographic VA Colour RC Manuel utilisateur

Renkforce

Renkforce 1208067 Manuel utilisateur

Levenhuk

Levenhuk Discovery Report WA40 Manuel utilisateur

Instant Transmission

Instant Transmission MA 10410 Manuel utilisateur

Lutron Electronics

Lutron Electronics PHB-318 Manuel utilisateur

WAREMA

WAREMA EWFS Weather station eco Manuel utilisateur

TFA

TFA 30.3013.IT Manuel utilisateur