TE Connectivity 46447 Manuel utilisateur

Instruction Sheet

1 of 8

*Trademark

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.

PRODUCT INFORMATION

1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com.

408-1542

07 FEB 19 Rev T

Figure 1

1. INTRODUCTION

Hand Crimping Tools 46447, 2326374-1, 47410 (crimps 12-10 AWG terminals on a 45° angle), 49592, 49935,

69363, 525693, 574573, 1490046-1, and 1490047-1 (shown in Figure 1) are used to crimp SOLISTRAND* and

STRATO-THERM* terminals and splices (listed in Figure 2) onto stranded wire sizes 26 through 10 AWG.

Read these instructions thoroughly before using the tool.

NOTE

Dimensions in this instruction sheet are in millimeters [with inch equivalents in brackets]. Figures and illustrations are for

reference only, and are not drawn to scale.

Reasons for reissue of this instruction sheet are provided in Section 7, REVISION SUMMARY.

2. DESCRIPTION

Each tool consists of a CERTI-CRIMP tool ratchet and two crimping jaws (indenter and anvil) containing one,

two, or three crimping chambers. Each tool is marked with the wire size range for each crimping chamber. See

Figure 1. Full crimping of the terminal or splice is assured by the CERTI-CRIMP tool ratchet. Once engaged,

the ratchet does not release until the tool handles have been FULLY closed.

CAUTION

The crimping jaws bottom before the ratchet releases. This feature ensures maximum electrical and tensile performance of the

crimp. Do NOT re-adjust the ratchet.

3. CRIMPING PROCEDURE

Strip the wire according to the dimensions listed in Figure 2. The strip length is determined by the type of

terminal or splice and by the wire size. Do not nick or cut the wire strands. Proceed as follows:

1. Close the tool handles until the ratchet releases. Allow the tool handles to open fully.

2. Center the terminal or splice wire barrel in the appropriate crimping chamber. For terminals, make

sure that the flat side of the tongue faces the anvil or the nest; for splices, make sure that the brazed

seam (when visible) is toward the indenter or, the nest. See Figure 3.

3. While holding the terminal or splice in place, squeeze the tool handles together just until the jaws

begin to close on the wire barrel. Do NOT deform the wire barrel.

4. Insert the stripped wire into the wire barrel, making sure that the wire insulation does not enter the

wire barrel.

PROPER USE GUIDELINES

Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low

volume applications. A wide selection of powered application equipment for extended-use, production operations is available.

Hand Crimping Tools 46447, 2326374-1,

47410, 49592, 49935, 69363, 525693,

574573, 1490046-1 and 1490047-1

408-1542

Rev T

2 of 8

Product

Hand Tool

Wire Size

(AWG) Range

and Terminal

Size

Crimping

Chamber

Marking

Wire Strip Length

Terminal

(Standard

Terminal

(Long Barrel)

Butt

Splice

Parallel

Splice

STRATO-THERM

46447

2326374-1

22-16

4.37-5.16

[.172-.203]

---

6.35-7.14

[.250-.281]

7.94-8.73

[.313-.344]

16-14

12-10

6.35-7.14

[.250-.281]

SOLISTRAND

49592

14-12

4.37-5.16

[.172-.203]

---

7.94-8.73

[.313-.344]

---

49935

525693

574573

22-16

4.37-5.16

[.172-.203]

6.35-7.14

[.250-.281]

6.35-7.14

[.250-.281]

7.94-8.73

[.313-.344]

49935

525693

574573

1490046-1

16-14

4.37-5.16

[.172-.203]

6.35-7.14

[.250-.281]

6.35-7.14

[.250-.281]

7.94-8.73

[.313-.344]

47410

49935

525693

574573

1490047-1

12-10 &

16-14 HD

12-10

6.35-7.14

[.250-.281]

---

6.35-7.14

[.250-.281]

---

69363

26-24

3.17-3.97

[.125-.156]

---

3.57-4.37

[.141-.172]

---

22-20

4.37-5.16

[.172-.203]

---

5.16-5.95

[.203-.234]

---

24-20

22-20

---

4.37-5.16

[.172-.203]

---

Figure 2

5. While holding the wire in place, squeeze the tool handles together until the ratchet releases, then

allow the tool handles to open fully.

6. To crimp the other half of a butt splice, position the uncrimped wire barrel in the crimping chamber,

and repeat the crimping procedure.

NOTE

If splice cannot be turned for crimping other half, turn the tool around.

NOTE

Terminals and splices can also be rotated 180 degrees with the seam toward the nest.

408-1542

Rev T

3 of 8

4. CRIMP INSPECTION

Inspect crimped terminals and splices by checking the features described in Figure 4. Poor crimps can be

avoided by carefully following the procedures provided in Section 3, and by following the tool maintenance

procedures provided in Section 5.

Figure 3

5. MAINTENANCE AND INSPECTION

The tool is inspected before being shipped, however TE recommends that the tool be inspected immediately

upon arrival at your facility to ensure that the tool has not been damaged during shipment.

Frequency of inspection depends on:

1. The care, amount of use, and handling of the hand tool.

2. The presence of abnormal amounts of dust and dirt.

3. The degree of operator skill; and

4. Your own established standards.

Daily Maintenance

1. Remove dust, moisture, and other contaminants with a clean brush, or a soft, lint--free cloth. Do NOT

use objects that could damage the tool.

2. Make certain that the retaining pins are in place and that they are secured with retaining rings.

3. All pins, pivot points, and bearing surfaces should be protected with a thin coat of any good SAE 20

motor oil. Do NOT oil excessively.

4. When the tool is not in use, keep handles closed to prevent objects from becoming lodged in the

crimping jaws. Store the tool in a clean, dry area.

Lubrication

Lubricate all pins, pivot points, and bearing surfaces with SAE 20 motor oil as follows:

Tools used in daily production - lubricate daily

Tools used daily (occasional) - lubricate weekly

Tools used weekly - lubricate monthly

Wipe excess oil from tool, particularly from crimping area. Oil transferred from the crimping area onto certain

terminations may affect the electrical characteristics of an application.

408-1542

Rev T

4 of 8

Figure 4

Periodic Inspection

1. The tool should be immersed (handles partially closed) in a reliable commercial degreasing compound

to remove accumulated dirt, grease, and foreign matter.

2. Close tool handles until ratchet releases and then allow them to open freely. If they do not open

quickly and fully, the spring is defective and must be replaced. See Section 6, REPLACEMENT AND

REPAIR.

3. Inspect head assembly for worn, cracked, or broken jaws. Refer to Figure 5. If damage is evident,

return the tool to TE for evaluation and repair. See Section 6, REPLACEMENT AND REPAIR.

408-1542

Rev T

5 of 8

Figure 5

Gaging the Crimping Chambers (Figure 7)

This inspection requires the use of a plug gage conforming to the dimensions provided in Figure 6.

TE does not manufacture or market these gages. To gage the crimping chambers, proceed as follows:

1. Remove traces of oil or dirt from the crimping chambers and plug gage.

2. Close the tool handles until it is evident that the jaws have bottomed; then hold in this position. Do

NOT force the jaws beyond initial contact.

3. Align the GO element with the crimping chamber. Push element straight into the crimping chamber

without using force. The GO element must pass completely through the crimping chamber.

4. Align the NO-GO element and try to insert it straight into the same crimping chamber. The NO-GO

element may start entry, but must not pass completely through the crimping chamber.

NOTE

The jaws in Tools 49935 and 574573 are not symmetrically located; make sure that the tool conforms to the symmetry

requirements shown in Figure 8.

If the crimping chambers conforms to the gage inspection, the tool is considered dimensionally correct, and

should be lubricated with a THIN coat of any good SAE 20 motor oil. If not, the tool must be returned for further

evaluation and repair. Refer to Section 6, REPLACEMENT AND REPAIR.

For additional information regarding the use of a plug gage, refer to Instruction Sheet 408-7424.

Ratchet Inspection

The CERTI-CRIMP tool ratchet should be checked to ensure that the ratchet does not release prematurely,

allowing the jaws to open before they have fully bottomed. Obtain a 0.025 mm [.001 in.] shim suitable for

checking the clearance between the bottoming surfaces of the crimping jaws. Proceed as follows:

1. Select a terminal or splice, and properly stripped wire with maximum wire load (such as wire size 16

AWG and size 22-16 terminal).

2. Position the terminal or splice and wire between the crimping jaws, as described in Section 3.

3. Hold the wire in place and squeeze the handles until the CERTI-CRIMP tool ratchet releases. Hold the

handles in this position, maintaining just enough tension to keep the jaws closed.

4. Check the clearance between the bottoming surfaces of the crimping jaws. If the clearance is 0.025

mm [.001 in.] or less, the ratchet is satisfactory. If clearance exceeds 0.025 mm [.001 in.], the ratchet

is out of adjustment and must be repaired. See Section 6, REPLACEMENT AND REPAIR.

408-1542

Rev T

6 of 8

Figure 6

Figure 7

Hand Tool

Crimping

Chamber

Marking

Gage Element Dimensions

NO-GO

“R”

46447

2326374-1

22-16

1.295-1.303 [.0510-.0513]

1.445-1.447 [.0569-.0570]

1.57 [.062]

16-14

1.498-1.506 [.0590-.0593]

1.648-1.651 [.0649-.0650]

1.57 [.062]

12-10

2.108-2.116 [.0830-.0833]

2.258-2.260 [.0889-.0890]

2.36 [.093]

49592

14-12

1.752-1.760 [.0690-.0693]

1.902-1.905 [.0749-.0750]

1.57 [.062]

49935

525693

574573

22-16

1.168-1.176 [.0460-.0463]

1.318-1.320 [.0519-.0520]

1.57 [.062]

49935

525693

574573

1490046-1

16-14

1.371-1.379 [.0540-.0543]

1.521-1.524 [.0599-.060]

1.98 [.078]

47410

49935

525693

574573

1490047-1

12-10

1.930-1.938 [.0760-.0763]

2.080-2.082 [.0819-.082]

2.76 [.109]

69363

26-24

0.660-0.668 [.026-.0263]

.0810-0.812 [.0319-.032]

1.003 [.0395]

22-20

0.939-0.947 [.037-.0373]

1.089-1.092 [.0429-.043]

1.19 [.047]

408-1542

Rev T

7 of 8

6. REPLACEMENT AND REPAIR

Customer-replaceable parts are listed in Figure 9. A complete inventory should be stocked and controlled to

prevent lost time when replacement of parts is necessary. Parts other than those listed should be replaced by

TE to ensure quality and reliability. Order replacement parts through your TE Representative, or call 1-800-526-

5142, or send a facsimile of your purchase order to 717-986-7605, or write to:

CUSTOMER SERVICE (038-035)

TE CONNECTIVITY CORPORATION

PO BOX 3608

HARRISBURG PA 17105-3608

Tools may also be returned to TE for evaluation and repair. For customer repair service, please contact a TE

Representative at 1-800-526-5136.

Figure 8

Figure 9

Replacement Parts

Item

Part Number

Description

Qty Per Tool

525693 Tool Only

21045-3

Ring, Retaining

---

1-23619-6

Ring, Retaining

39364

Spring, Hold Down

---

2-23620-9

Pin, Straight, Grooved

21045-6

Ring, Retaining

525108

Ring, Retaining, Beryl Copper

---

408-1542

Rev T

8 of 8

7. REVISION SUMMARY

Figure 2 added 16-14 HD AWG Wire Size (AWG) Range and Terminal Size to SOLISTRAND 12-10

AWG

Figure 2 and Figure 6 changed Hand Tool Number from 525623 (22-16 AWG) to 525693

Autres manuels pour 46447

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels TE Connectivity Outils de sertissage

TE Connectivity

TE Connectivity 234170-1 Manuel utilisateur

TE Connectivity

TE Connectivity SDE-SA Manuel utilisateur

TE Connectivity

TE Connectivity 2217480 Series Guide de référence

TE Connectivity

TE Connectivity ERGOCRIMP 539 664-2 Manuel utilisateur

TE Connectivity

TE Connectivity ERGOCRIMP 4-1579001-6 Manuel utilisateur

TE Connectivity

TE Connectivity SDE-SA Manuel utilisateur

TE Connectivity

TE Connectivity SDE-SA Manuel utilisateur

TE Connectivity

TE Connectivity 46447 Manuel utilisateur

TE Connectivity

TE Connectivity 2395308-1 Manuel utilisateur

TE Connectivity

TE Connectivity 575937 Manuel utilisateur

TE Connectivity

TE Connectivity CERTI-CRIMP 90066-7 Manuel utilisateur

TE Connectivity

TE Connectivity 2063490-1 Manuel utilisateur

TE Connectivity

TE Connectivity 2393700-1 Manuel utilisateur

TE Connectivity

TE Connectivity CERTI- CRIMP Series Manuel utilisateur

TE Connectivity

TE Connectivity 2381454-1 Mode d’emploi

TE Connectivity

TE Connectivity PRO-CRIMPER III Manuel utilisateur

TE Connectivity

TE Connectivity SDE-SA Manuel utilisateur

TE Connectivity

TE Connectivity 2390075-1 Manuel utilisateur

TE Connectivity

TE Connectivity 90382- 2 Manuel utilisateur

TE Connectivity

TE Connectivity 2359761-1 Manuel utilisateur

TE Connectivity

TE Connectivity 58075-1 Manuel utilisateur

TE Connectivity

TE Connectivity AMPOWER 68361-1 Manuel utilisateur

TE Connectivity

TE Connectivity ERGOCRIMP 539671-2 Manuel utilisateur

TE Connectivity

TE Connectivity 90117 Mode d’emploi

Manuels Outils de sertissage populaires d'autres marques

Panduit

Panduit CT-1000 Guide de l'administrateur

JST

JST CS 10 Manuel utilisateur

molex

molex 63811-5100 Manuel utilisateur

Danfoss

Danfoss ET4200 Manuel utilisateur

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuel utilisateur

molex

molex 63825-3000 Manuel utilisateur

Tyco Electronics

Tyco Electronics 69156-1 Manuel utilisateur

CRH

CRH CRL CBLHCT1 Manuel utilisateur

Emerson

Emerson Klauke ES 105CFM Manuel utilisateur

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Mode d’emploi

Danfoss

Danfoss ET4350 Manuel utilisateur

Milwaukee

Milwaukee M18 Manuel utilisateur

HOGERT

HOGERT HT1P169 Manuel utilisateur

Textron

Textron ESG105L Manuel utilisateur

Tyco Electronics

Tyco Electronics 90035-3 Manuel utilisateur

Emerson

Emerson Klauke ES 20RMCCFB Manuel utilisateur

Continental Refrigerator

Continental Refrigerator PC150HD Manuel utilisateur

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manuel utilisateur