TE Connectivity PRO-CRIMPER III Manuel utilisateur

Instruction Sheet

*Trademark

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.

1of 5

TOOLING ASSISTANCE CENTER

1-800-722-1111

PRODUCT INFORMATION

1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com LOC B

408-9938

PRO-CRIMPER* III Hand

Crimping Tool Assembly 90758-1

with Die AssemblY 90758-2 01 NOV 11 Rev D

PROPER USE GUIDELINES

Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use

and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available.

†Supplied with die assembly. Also available separately.

‡Contact the TOOLING ASSISTANCE CENTER or PRODUCT INFORMATION (see below) for specific contact part numbers.

Figure 1

1. INTRODUCTION

PRO-CRIMPER III Hand Crimping Tool Assembly

90758-1 consists of Die Assembly 90758-2 and

PRO-CRIMPER III Hand Crimping Tool Frame

354940-1 (see Instruction Sheet 408-9930). The die

assembly consists of crimping dies and a locator

assembly.

Read these instructions thoroughly before crimping

any contacts.

Dimensions in this instruction sheet are in

millimeters [with inch equivalents provided in

brackets]. Figures and illustrations are for

reference only and are not drawn to scale.

Reasons for reissue of this instruction sheet are

provided in Section 11, REVISION SUMMARY.

2. DESCRIPTION (See Figures 1 and 2)

The tool consist of a stationary jaw and handle, a

moving jaw and handle, and an adjustable ratchet that

ensures full contact crimping. The tool frame holds a

die assembly with two crimping sections.

The die assembly features a wire anvil, an insulation

anvil, a wire crimper, and an insulation crimper.

Attached to the outside of the frame is a locator

assembly, which contains a locator, spring retainer,

and a contact support.

Die retaining pins and die retaining screws are used to

position and secure the dies in the tool frame. A nut is

used on the upper die retaining screw to hold the

locator assembly in place.

Locator Assembly

(Supplied with Die Assembly

Moving Jaw

Die Assembly

Stationary Jaw Back of Tool Frame

(Wire Side)

Pivot Pin

Ratchet

Adjustment

Wheel

PRO-CRIMPER III Hand Tool

Frame 354940-1 (408-9930)

Stationary Handle

Moving Handle

The PRO-CRIMPER III Hand Crimping Tool is a “Commercial” grade tool and is designed

primarily for field installation, repair, maintenance work, or prototyping in industrial,

commercial, or institutional applications. Product crimped with this tool will meet the crimp

height requirement for handtoolsintheappropriateApplicationSpecification (114-series),

but may not comply with other feature parameters of the specification.

TE Connectivity offers a variety of tools to satisfy your performance requirements.

For additional information, contact the Tooling Assistance Center at 1-800-722-1111.

Front of Tool

(Locator Side)

TE DIE

ASSEMBLY TE LOCATOR

ASSEMBLY† CONTACT

FAMILY‡ WIRE

SIZE (AWG) INSUL DIA STRIP LENGTH

90758-2 58516-1 Mini Universal

MATE-N-LOK*

Connectors 26-22 1.19-1.75

[.047-.069] 3.20 to 3.71

[.126 to .146]

NOTE

ORIGINAL INSTRUCTIONS

408-9938

2of 5

Rev D

Figure 2

3. INSTALLATION AND REMOVAL OF DIE SET AND

LOCATOR ASSEMBLY (Figure 2)

1. Open the tool handles and remove the two die

retaining screws from the tool jaws.

2. Place the wire anvil and insulation anvil so that

their chamfered sides and their marked surfaces

face outward, when mounted in the moving jaw of

the tool frame.

3. Insert the two die retaining pins.

4. Insert the short die retaining screw through the

jaw and through both anvil dies, and tighten the

screw just enough to hold the dies in place. Do NOT

tighten the screw completely at this time.

5. Place the wire crimper and insulation crimper so

that their chamfered sides and their marked

surfaces face outward, when mounted in the

stationary jaw of the tool frame.

6. Insert the two retaining pins.

7. Insert the long die retaining screw through the

jaw and through both crimper dies, and tighten the

screw just enough to hold the dies in place. Do NOT

tighten the screw completely at this time.

8. Carefully close the tool handles, making sure that

the anvils and crimpers align properly. Continue

closing the tool handles until the ratchet in the tool

frame has engaged sufficiently to hold the anvils

and crimpers in place, then tighten both die

retaining screws.

9. Place the locator assembly over the end of the

long screw, and position the locator assembly

against the side of the tool jaw.

10. Place the nut onto the end of the long screw and

tighten the nut enough to hold the locator assembly

in place, while still allowing the locator to slide up

and down.

11. To disassemble, close the tool handles until the

ratchet releases, remove the nut, the locator

assembly, the two die retaining screws, and the four

die retaining pins, and slide the anvils and crimpers

out of the tool jaws.

4. CONTACT SUPPORT ADJUSTMENT (Figure 3)

The contact support is presetprior to shipment, but

minor adjustment may be necessary.

1. Make a sample crimp and determine if the

contact is straight, bending upward, or bending

downward.

2. If adjustment is required, loosen the screw that

holds the contact support onto the locator assembly.

The ratchet has detents that create audible clicks

as the tool handles are closed.

3. Place a contact with wire into the proper nest and

close the tool handles until the ratchet reaches the

sixth click, or until the contact support touches the

contact.

4. Slightly loosen the nut that holds the locator

assembly onto the tool frame.

5. Move the contact support as required to eliminate

the bending of the contact.

Tool Frame

DieRetaining

Screw

DieRetaining

Screw

Die Retaining Pins

Locator AssemblyNut

Locator

Chamfer

Wire Crimper

Insulation Anvil Chamfer

Insulation

Crimper

Offset

Wire Anvil

NOTE

408-9938

3of 5

Rev D

6. Tighten the nut and close the handles until the

ratchet releases.

7. Remove and inspect the contact.

8. Make another sample crimp. If the contact is

straight, tighten the contact support screw. If the

contact is still being bent during crimping, repeat the

adjustment procedure.

5. CRIMPING PROCEDURE

This tool is provided with a crimp adjustment

feature. Initially, the crimp height should be verified

asspecified in Figure 4.Refer to Section 6, CRIMP

HEIGHT INSPECTION, and Section7, RATCHET

ADJUSTMENT, to verify crimp height before using

the tool to crimp desired contacts and wire sizes.

Refer to the table in Figure 1 and select wire of the

specified size and insulation diameter. Strip the wire to

the length indicated in Figure 1, taking care not to nick

or cut wire strands. Select an applicable contact and

identify the appropriate crimp section according to the

wire size markings on the tool. Refer to Figure 3 and

proceed as follows:

1. Hold the tool so that the back (wire side) is facing

you. Squeeze tool handles together and allow them

to open fully.

2. Holding the contact by the mating end, insert the

contact — insulation barrel first — through the front

of the tool and into the appropriate crimp section.

3. Position the contact so that the mating end of the

contact is on the locator side of the tool, and so that

the open “U” of the wire and insulation barrels face

the top of the tool. Place the contact up into the nest

so that the movable locator drops into the slot in the

contact. Refer to Figure 3. Butt the front end of the

wire barrel against the movable locator.

Make sure that both sides of the insulation barrel

are started evenly into the crimping section. Do

NOT attempt to crimp an improperly positioned

contact.

4. Hold the contact in position and squeeze the tool

handles together until ratchet engages sufficiently to

hold the contact in position. Do NOT deform

insulation barrel or wire barrel.

5. Insert stripped wire into contact insulation and

wire barrels until it is butted against the wire stop, as

shown in Figure 3.

6. Holding the wire in place, squeeze tool handles

together until ratchet releases. Allow tool handles to

open and remove crimped contact.

Thecrimpedcontactmaystickinthecrimpingarea,

but the contact can be easily removed by pushing

downward on the top of the locator (see Figure 3).

7. Check the contact’s crimp height as described in

Section 6, CRIMP HEIGHT INSPECTION. If

necessary, adjust the crimp height as described in

Section 7, RATCHET (Crimp Height)

ADJUSTMENT.

Figure 3

NOTE

CAUTION

NOTE

AdjustmentScrewfor

Contact Support

Contact

Support Locator

Backof Tool

(Wire Side)

Wire

Locator in

Wire Stop

Contact

(Typ)

Strip

Length

WireInserted

to Stop

408-9938

4of 5

Rev D

6. CRIMP HEIGHT INSPECTION

Crimp height inspection is performed through the use

of a micrometer with a modified anvil, commonly

referred to as a crimp-height comparator. TE does not

manufacture or market crimp-height comparators.

Detailed information on obtaining and using crimp-

height comparators can be found in Instruction Sheet

408-7424.

Proceed as follows:

1. Refer to Figure 4 and select a wire (maximum

size) for each crimp section listed.

2. Refer to Section 5, CRIMPING PROCEDURE,

and crimp the contact(s) accordingly.

Figure 4

3. Using a crimp height comparator, measure the

wire barrel crimp height as shown in Figure 4. If the

crimp height conforms to that shown in the table,

the tool is considered dimensionally correct. If not,

the tool must be adjusted. Refer to Section 7,

RATCHET (Crimp Height) ADJUSTMENT.

7. RATCHET (Crimp Height) ADJUSTMENT (Figure 5)

1. Remove the lockscrew from the ratchet

adjustment wheel.

2. Using a screwdriver, adjust the ratchet wheel

from the locator side of the tool.

3. Observe the ratchet adjustment wheel. If a tighter

crimp is required, rotate the adjustment wheel

counterclockwise to a higher-numbered setting. If a

looser crimp is required, rotate the adjustment

wheel clockwise to a lower-numbered setting.

4. Replace the lockscrew.

5. Make a sample crimp and measure the crimp

height. If the dimension is acceptable, replace and

secure the lockscrew. If the dimension is

unacceptable, continue to adjust the ratchet, and

again measure a sample crimp.

Figure 5

8. MAINTENANCE

Ensure that the tool frame and dies are clean by

wiping them with a clean, soft cloth. Remove any

debris with a clean, soft brush. Do not use objects that

could damage the tool. When not in use, keep tool

handles closed to prevent objects from becoming

lodged in the dies, and store in a clean, dry area.

9. VISUAL INSPECTION

The crimping dies should be inspected on a regular

basis to ensure that they have not become worn or

damaged. Inspect the crimp sections for flattened,

chipped, worn, or broken areas. If damage or

abnormal wear is evident, the tool must be replaced.

See Section 10, REPLACEMENT.

10. REPLACEMENT

Customer-replaceable parts are shown in Figure 1.

Available separately, PRO-CRIMPER III Hand

Crimping Tool Repair Kit 679221-1 includes a

replacement nut and a variety of pins, rings, screws,

and springs. If the dies are damaged or worn

excessively, they must be replaced.

Order the repair kit and replaceable parts through your

TE Representative, or call 1-800-526-5142, or send a

facsimile of your purchase order to

1-717-986-7605, or write to:

CUSTOMER SERVICE (038-035)

TYCO ELECTRONICS CORPORATION

PO BOX 3608

HARRISBURG PA 17105-3608

11. REVISION SUMMARY

Revisions to this instruction sheet include:

•Updated document to corporate requirements

•Corrected tooling information in Section 1,

INTRODUCTION

WIRE SIZE

AWG (Max)

CRIMP SECTION

(Wire Size

Marking)

CRIMP HEIGHT

DIMENSION “A”

(±0.05 [±.002])

24 26-24 0.69 [.027]

18 22 0.79 [.031]

PositionPoint

on Center of

Wire Barrel

Opposite

Modified Anvil “A”

Screwdriver

Lockscrew

RatchetAdjustment

Wheel

408-9938

5of 5

Rev D

Tooling Compatible with Die Assembly 90758-2

PRO-CRIMPER III Hand Tool Frame 354940-1

(Instruction Sheet 408-9930) SDE-SA Hand Tool 9-1478240-0

(Instruction Sheet 408-8851)

SDE Bench Terminator 1490076-2

(Customer Manual 409-10052) 626 Adapter 679304-1

(Instruction Sheet 408-4070)

Electro-Hydraulic (BT 3500 Battery-Hydraulic)

Hand Tool Kits 2031400-[ ]

(Customer Manual 409-10095) “C”-Head Assembly 2031450-1

(Instruction Sheet 408-10311)

Closed Head Assembly 2031460-1

(Instruction Sheet 408-10312)

Authorized Distribution Brand：

Website：

Welcome to visit www.ameya360.com

Address：

401 Building No.5, JiuGe Business Center, Lane 2301, Yishan Rd

Minhang District, Shanghai , China

Sales：

Direct +86 (21) 6401-6692

Email [email protected]

QQ 800077892

Skype ameyasales1 ameyasales2

Customer Service：

Email [email protected]

Partnership：

Tel +86 (21) 64016692-8333

Email [email protected]

Autres manuels pour PRO-CRIMPER III

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels TE Connectivity Outils de sertissage

TE Connectivity

TE Connectivity 69376 Manuel utilisateur

TE Connectivity

TE Connectivity SDE-SA 2389861-1 Manuel utilisateur

TE Connectivity

TE Connectivity SOLISTRAND 1752868-1 Manuel utilisateur

TE Connectivity

TE Connectivity 2063536-1 Manuel utilisateur

TE Connectivity

TE Connectivity 2063567-1 Manuel utilisateur

TE Connectivity

TE Connectivity 59974-1 Manuel utilisateur

TE Connectivity

TE Connectivity PRO- CRIMPER III Manuel utilisateur

TE Connectivity

TE Connectivity 2392945-1 Manuel utilisateur

TE Connectivity

TE Connectivity ERGOCRIMP 539 725-2 Manuel utilisateur

TE Connectivity

TE Connectivity 1213875 Series Manuel utilisateur

TE Connectivity

TE Connectivity PRO-CRIMPER III Manuel utilisateur

TE Connectivity

TE Connectivity 2063534-1 Manuel utilisateur

TE Connectivity

TE Connectivity SDE-SA Manuel utilisateur

TE Connectivity

TE Connectivity COPALUM 408-2281 Manuel utilisateur

TE Connectivity

TE Connectivity SDE-SA Manuel utilisateur

TE Connectivity

TE Connectivity SDE Manuel utilisateur

TE Connectivity

TE Connectivity 2390275-1 Manuel utilisateur

TE Connectivity

TE Connectivity PRO-CRIMPER III Manuel utilisateur

TE Connectivity

TE Connectivity 2844461-2 Manuel utilisateur

TE Connectivity

TE Connectivity ERGOCRIMP 5-1579001-3 Manuel utilisateur

TE Connectivity

TE Connectivity SDE-SA Manuel utilisateur

TE Connectivity

TE Connectivity 2063490-1 Manuel utilisateur

TE Connectivity

TE Connectivity PDT-48-00 Manuel utilisateur

TE Connectivity

TE Connectivity ERGOCRIMP 0-539956-2 Manuel utilisateur

Manuels Outils de sertissage populaires d'autres marques

Panduit

Panduit CT-1000 Guide de l'administrateur

JST

JST CS 10 Manuel utilisateur

molex

molex 63811-5100 Manuel utilisateur

Danfoss

Danfoss ET4200 Manuel utilisateur

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuel utilisateur

molex

molex 63825-3000 Manuel utilisateur

Tyco Electronics

Tyco Electronics 69156-1 Manuel utilisateur

CRH

CRH CRL CBLHCT1 Manuel utilisateur

Emerson

Emerson Klauke ES 105CFM Manuel utilisateur

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Mode d’emploi

Danfoss

Danfoss ET4350 Manuel utilisateur

Milwaukee

Milwaukee M18 Manuel utilisateur

HOGERT

HOGERT HT1P169 Manuel utilisateur

Textron

Textron ESG105L Manuel utilisateur

Tyco Electronics

Tyco Electronics 90035-3 Manuel utilisateur

Emerson

Emerson Klauke ES 20RMCCFB Manuel utilisateur

Continental Refrigerator

Continental Refrigerator PC150HD Manuel utilisateur

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manuel utilisateur