TE Connectivity 58075-1 Manuel utilisateur
Instruction Sheet
1 of 7
© 2021 TE Connectivity Ltd. family of companies.
All Rights Reserved.
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.
PRODUCT INFORMATION
1-800-522-6752
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com.
408-6789
28 SEP 2021 Rev F
PROPER USE GUIDELINES
Cumulative trauma disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional
use and low-volume applications. A wide selection of powered application equipment is available for extended-use production operations.
Figure 1: Pistol Grip Pneumatic Handle Assembly 58075-1
1
Air cylinder
2
Body
3
Key (visible on this side)
4
Trigger
5
Handle
6
Air tube
1. INTRODUCTION
These instructions deal with the safety, installation, operation and maintenance of the Pistol Grip Pneumatic
Handle Assembly 58075-1 (Figure 1).
Pistol Grip Pneumatic Handle Assembly 58075-1 accepts interchangeable terminating heads that terminate
wires in connectors. To ensure accurate termination of wires, setup adjustments, and head maintenance, refer
to the instructions packaged with the terminating head.
NOTE
Dimensions in this instruction sheet are in millimeters with [inches in brackets]. Figures are for reference only and are not
drawn to scale.
Reasons for reissue of this instruction sheet are provided in section 8, REVISION SUMMARY.
Pistol Grip Pneumatic
Handle Assembly 58075-1
408-6789
Rev F
2 of 7
2. DESCRIPTION
The pneumatic handle assembly features a molded nylon handle with a trigger and an air tube. The handle
holds an air cylinder with a key that retains the terminating head in the body and allows the head to be rotated
(Figure 1).
In this use, the handle assembly with the terminating head emits a maximum noise level of 78 dB. The vibration
level is less than 2.5 mm/s².
Figure 2 shows the dimensions of the handle assembly. The weight is 510 g [1 lb, 2 oz].
Figure 2: Dimensions
408-6789
Rev F
3 of 7
3. INSTALLING AND REMOVING THE HEAD
DANGER
To avoid personal injury, always disconnect the handle assembly from the air supply when installing or removing the head.
1. Disconnect or lock out the tool from its air supply.
2. Position the blade tip of a screwdriver between the shoulder of the key and the handle assembly body.
Pry and remove the key (Figure 3).
3. Insert the terminating head into the head entrance until the head bottoms (Figure 3).
Figure 3: Inserting the terminating head
1
Key
2
Terminating head (for reference)
3
Head entrance
4. Re-insert the key to retain the head.
5. To remove the head, remove the key and pull the head out of the handle assembly.
408-6789
Rev F
4 of 7
4. SETUP
Use a regulator-filter-lubricator unit with the lubricator adjusted to the minimum setting (Figure 4).
Figure 4: Regulator-filter-lubricator unit
1
Air supply
2
Filter and moisture separator
3
Regulator
4
Lubricator
5
To handle assembly
Use quick-disconnect fittings to connect the tool to the air supply. If not using quick-disconnect fittings, provide
a pneumatic lock-out on the air line that bleeds air after it is turned off.
The handle assembly is designed to operate with an air pressure range of 276 to 483 kPa [40 to 70 psi].
Service life can be greatly extended when only the necessary air pressure is applied. Excessive pressure
causes wear and strain on handle assembly components and the connectors.
CAUTION
Do not use this tool as a blunt object, a crushing device, or for any purpose other than crimping the proper specified product.
Inappropriate use of the tool can result in personal injury or damage to the tool.
5. OPERATION
The following procedure provides only general information concerning crimping. Refer to the instructions
packaged with the terminating heads for detailed information, including wire stripping dimensions and
instructions for positioning terminals in the terminating heads.
1. Insert the connector into the left side of the head.
2. Align the contact to be terminated with the wire inserter of the head. Make sure that the locating pawl
rests between the connector index ribs.
3. Insert an unstripped wire into the funnel area between the contact and the wire inserter until it bottoms
on the tool base.
4. Press the trigger of the handle assembly and hold it until the wire inserter bottoms.
5. Release the trigger. The wire inserter retracts. The feed slide automatically advances the connector to
the next contact position.
6. Repeat steps 2 through 5 until all contacts have been terminated.
7. Inspect each termination.
408-6789
Rev F
5 of 7
6. MAINTENANCE AND INSPECTION
DANGER
To avoid personal injury, always disconnect the handle assembly from the air supply when performing maintenance or
inspection procedures.
Each handle assembly is inspected before shipment. Inspect the handle assembly immediately upon arrival at
the facility of use to ensure that it has not been damaged during shipping.
6.1. Daily maintenance
Each operator of the power unit must be aware of, and responsible for, the following daily maintenance
requirements:
1. Remove dust, dirt and other contaminants with a clean brush or soft lint-free cloth. Do not use objects
that could damage the handle assembly.
2. Ensure that all components are in place and properly secured.
3. With the terminating head in place, connect the air supply.
4. Squeeze and release the trigger to ensure that the mechanisms and plunger move smoothly.
6.2. Periodic inspection
Regular inspections must be performed at least once per month. Base your inspection frequency on
amount of use, the presence of abnormal amounts of dust and dirt, operator training and skill, and
established company standards.
Remove any accumulated film with a suitable cleaning agent that does not affect plastic material.
Check the handle assembly for chipped, cracked, worn, or broken areas. If damage is evident, repair is
necessary. See section 7, REPLACEMENT AND REPAIR.
408-6789
Rev F
6 of 7
7. REPLACEMENT AND REPAIR
Customer-replaceable parts are shown in Figure 5.
Figure 5: Customer-replaceable parts
Item
Part number
Description
Quantity per
assembly
1
27174-1
Valve, poppet
1
2
1-21003-3
Screw, flat head socket cap
1
3
28472-1
Push button trigger, valve actuator
1
4
312140-1
Key
1
5
312141-1
Nut, cam adjustment
1
6
312157-1
Air cylinder
1
7
310421-1
Plug, cap
1
8
310424-1
Bracket, air cylinder
1
9
21086-6
O-ring
2
10
312156-1
Handle
1
11
312622-2
Subassembly, air tube
1
Stock and control a complete inventory to prevent lost time when replacement of parts is necessary. Parts
other than those listed should be replaced by TE to ensure quality and reliability of the handle assembly. Order
replacement parts through your TE representative. You can also order parts by any of the following methods:
Go to TE.com and click the Shop TE link at the top of the page.
Call 800-522-6752.
Write to:
CUSTOMER SERVICE (038-035)
TE CONNECTIVITY CORPORATION
PO BOX 3608
HARRISBURG PA 17105-3608
For customer repair services, call 800-522-6752.
Table des matières
Autres manuels TE Connectivity Outils de sertissage
TE Connectivity
TE Connectivity 2380840-1 Manuel utilisateur
TE Connectivity
TE Connectivity 2063528-1 Manuel utilisateur
TE Connectivity
TE Connectivity 90117 Mode d’emploi
TE Connectivity
TE Connectivity 2407132-1 Manuel utilisateur
TE Connectivity
TE Connectivity SDE-SA Manuel utilisateur
TE Connectivity
TE Connectivity ERGOCRIMP 4-1579001-6 Manuel utilisateur
TE Connectivity
TE Connectivity 1-45216-0 Manuel utilisateur
TE Connectivity
TE Connectivity 825508-5 Manuel utilisateur
TE Connectivity
TE Connectivity Positive Lock A Manuel utilisateur
TE Connectivity
TE Connectivity MQS 3-1579014-9 Manuel utilisateur
TE Connectivity
TE Connectivity SDE-SA Manuel utilisateur
TE Connectivity
TE Connectivity SDE-SA Manuel utilisateur
TE Connectivity
TE Connectivity IDC Hand tool RAST 2.5 Manuel utilisateur
TE Connectivity
TE Connectivity TETRA-CRIMP 59824-1 Manuel utilisateur
TE Connectivity
TE Connectivity 59974-1 Manuel utilisateur
TE Connectivity
TE Connectivity 2063573-1 Manuel utilisateur
TE Connectivity
TE Connectivity SDE-SA 2391790-1 Manuel utilisateur
TE Connectivity
TE Connectivity 2392900-1 Manuel utilisateur
TE Connectivity
TE Connectivity 2386893-1 Manuel utilisateur
TE Connectivity
TE Connectivity 575937 Manuel utilisateur
Manuels Outils de sertissage populaires d'autres marques
HOGERT
HOGERT HT1P169 Manuel utilisateur
Textron
Textron ESG105L Manuel utilisateur
Tyco Electronics
Tyco Electronics 90035-3 Manuel utilisateur
Emerson
Emerson Klauke ES 20RMCCFB Manuel utilisateur
Continental Refrigerator
Continental Refrigerator PC150HD Manuel utilisateur
Tyco Electronics
Tyco Electronics CERTI-CRIMP 90418-1 Manuel utilisateur