TE Connectivity 2844461-2 Manuel utilisateur

Instruction Sheet

1 of 5

*Trademark

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.

PRODUCT INFORMATION

1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com.

408-35019

20 MAR 17 Rev A

Part Number

Wire Dimensions

Die

Locator

Assembly(1)

MOLEX

Contact

Size

[mm2]

Insulation

Diameter

Strip

Length

2844461-2

2063771-1

39-00-0429

39-00-0038

39-00-0220

39-00-0041

44476-1112

44478-1112

45750-1212

22-20 AWG

[0.30-0.50]

.067 - .091

[1.70 - 2.31]

.118 - .130

[3.00 - 3.30]

18AWG

[0.80]

.067 - .091

[1.70 - 2.31]

45750-3212

16AWG

[1.30]

.090 - .114

[2.29 - 2.90]

(1) Supplied with die assembly. Also available separately.

Figure 1

1. INTRODUCTION

This die assembly is used with SDE Closed Head Battery Tool 2217481-[ ] to crimp the contact/wire

combinations listed in Figure 1.

PROPER USE GUIDELINES

Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low

volume applications. A wide selection of powered application equipment for extended-use, production operations is available.

SDE Die Assembly; PN 2844461-2

This die is a “commercial" grade die and is designed

primarily for field installation, repair, maintenance work, or prototyping in industrial, commercial,

or institutional applications. Product crimped with this tool will meet the crimp height requirement for hand tools in the appropriate 114 Series

Application Specification, but may not comply with other feature parameters of the specification. TE Connectivity (TE) offers a variety of tools to

satisfy your performance requirements. For additional information, call the number at the bottom of this page.

408-35019

Rev A

2 of 5

2. DESCRIPTION

Die components are shown in Figure 1.

NOTE

Dimensions in this Instruction Sheet are in inches [with millimeters in brackets]. Figures are not drawn to scale.

3. INSTALLATION AND REMOVAL OF DIE ASSEMBLY

NOTE

Refer to Figure 1, Figure 2, and Customer Manual 409-32032, Section 4.2, for die assembly and removal.

NOTE: Die Installation in PN 2217481 Head

Figure 2

3. CONTACT SUPPORT ADJUSTMENT

NOTE

Due to the inclusion of a lower locating block, the contact support is not used to straighten the terminal in this application and

should be kept in the highest possible position.

Figure 3

Contact

Support

Adjustment Screw

for Contact Support

Locator

Note: Not to Scale

Strip Length (Ref)

Wire Inserted

to Stop

Locator in

Contact

Wire Stop Slot

Contact

(Typ)

Lower

Locator

Block

408-35019

Rev A

3 of 5

4. CRIMPING PROCEDURE

NOTE

Before using the tool for production, the contact crimp height should be verified as described in Section 5.

1. Refer to Figure 1 and select the appropriate wire and crimp nest for the contact to be crimped.

2. Strip the wire to the length indicated in Figure 1. DO NOT nick or cut wire strands.

3. Ensure the die is fully opened.

4. Holding the contact by the insulation barrel with the “U” of the wire barrel facing the top of the tool,

insert the contact mating end through the die into the appropriate chamber in the lower locating block.

Push the terminal forward until it is stopped by the lower locator, the back of the insulation barrel

should be flush or slightly deeper than the edge of the insulation anvil.

CAUTION

Make sure both sides of the insulation barrel are started evenly into the crimping chamber. Do not attempt to crimp an

improperly positioned contact.

5. Actuate the ram until the die is closed to the point at which the legs of the insulation barrel contact the

sides of the insulation crimper. Closing the die too far will prevent larger insulation diameter

wires from being inserted properly.

6. Insert the stripped wire into the wire barrel until it butts against the wire stop as shown in Figure 3.

7. Holding the wire in place, complete the crimp by actuating the ram until the crimp is complete and the

tool opens. Remove the crimped contact.

8. Check the contact crimp height as described in Section 5.

5. CRIMP HEIGHT INSPECTION

1. Refer to Figure 4, and select a maximum size wire.

2. Crimp the contact.

3. Using a crimp height micrometer, measure the crimp height as shown in Figure 4. If the crimp height

conforms, the tool is considered dimensionally correct.

NOTE

Detailed information on obtaining and using crimp height comparators can be found in Instruction Sheet 408-7424.

MAXIMUM

WIRE SIZE

[mm2]

CRIMPING

CHAMBER

(Wire Size Marking)

CRIMP

HEIGHT

20 AWG

[0.50]

24-20

.035±.002

[.89± 0.05]

18 AWG

[0.80]

.041±.002

[1.04± 0.05]

16 AWG

[1.30]

.044±.002

[1.12± 0.05]

Figure 4

Point on Center

of Wire Barrel

Opposite Seam

Modified Anvil

Crimp Height

(Refer to

Table)

408-35019

Rev A

4 of 5

6. TOOL MAINTENANCE AND INSPECTION

6.1. Maintenance

1. Ensure that the tool and dies are clean by wiping them with a clean, soft cloth. Remove any debris

with a clean, soft brush. Do not use objects that could damage any components.

2. Remove all lubrication and accumulated film from the dies by immersing the dies in a suitable

commercial degreaser.

6.2. Visual Inspection

1. Inspection of the tool and dies should be made on a regular basis to ensure they have not become

worn or damaged.

2. Make sure the applicable die retaining screws are properly secured.

3. Inspect the crimping chamber of the die assembly for flattened, chipped, worn, or broken areas. If

damage or abnormal wear is evident, the dies must be replaced. Refer to Section 7.

7. REPLACEMENT

If the dies are damaged or worn excessively, they must be replaced. Order dies through your representative;

call 1-800-522-6752, send a facsimile of your purchase order to 717-986-7605, or write to:

CUSTOMER SERVICE (038-035)

TE CONNECTIVITY CORPORATION

PO BOX 3608

HARRISBURG PA 17105-3608

8. REVISION SUMMARY

Initial Release

408-35019

Rev A

5 of 5

Tooling Compatible with Die Assembly PN 2844461-2

Figure 5

PRO-CRIMPER III Hand Tool Frame 354940-1

(Instruction Sheet 408-9930)

SDE-SA Hand Tool 9-1478240-0

(Instruction Sheet 408-8851)

SDE Bench Terminator 1490076-2

(Customer Manual 409-10052)

626 Adapter 679304-1

(Instruction Sheet 408-4070)

Battery Tool (Shouldered Die) 1725837-1 and -2

(Customer Manual 409-10053)

Battery Tool 2217481-1 and -2

(Customer Manual 409-32032)

Table des matières

Autres manuels TE Connectivity Outils de sertissage

TE Connectivity

TE Connectivity 2372541-1 Manuel utilisateur

TE Connectivity

TE Connectivity 58422-1 Manuel utilisateur

TE Connectivity

TE Connectivity SDE-SA Manuel utilisateur

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manuel utilisateur

TE Connectivity

TE Connectivity 90080-2 Manuel utilisateur

TE Connectivity

TE Connectivity PRO- CRIMPER III Manuel utilisateur

TE Connectivity

TE Connectivity 2390409-1 Manuel utilisateur

TE Connectivity

TE Connectivity 46754-2 Manuel utilisateur

TE Connectivity

TE Connectivity 90084 Manuel utilisateur

TE Connectivity

TE Connectivity 2359761-1 Manuel utilisateur

TE Connectivity

TE Connectivity PRO-CRIMPER III Manuel utilisateur

TE Connectivity

TE Connectivity PRO-CRIMPER III 58521-1 Manuel utilisateur

TE Connectivity

TE Connectivity 2391435-1 Manuel utilisateur

TE Connectivity

TE Connectivity 2392221-1 Manuel utilisateur

TE Connectivity

TE Connectivity 2063624-1 Manuel utilisateur

TE Connectivity

TE Connectivity ERGOCRIMP 2-1579016-2 Manuel utilisateur

TE Connectivity

TE Connectivity PRO-CRIMPER III Manuel utilisateur

TE Connectivity

TE Connectivity 539 726-2 Manuel utilisateur

TE Connectivity

TE Connectivity 2397100-1 Manuel utilisateur

TE Connectivity

TE Connectivity TERMI-FOIL 68026 Manuel utilisateur

TE Connectivity

TE Connectivity PDT-48-00 Manuel utilisateur

TE Connectivity

TE Connectivity 2395308-1 Manuel utilisateur

TE Connectivity

TE Connectivity 2390882-1 Manuel utilisateur

TE Connectivity

TE Connectivity SDE-SA Manuel utilisateur

Manuels Outils de sertissage populaires d'autres marques

Panduit

Panduit CT-1000 Guide de l'administrateur

JST

JST CS 10 Manuel utilisateur

molex

molex 63811-5100 Manuel utilisateur

Danfoss

Danfoss ET4200 Manuel utilisateur

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuel utilisateur

molex

molex 63825-3000 Manuel utilisateur

Tyco Electronics

Tyco Electronics 69156-1 Manuel utilisateur

CRH

CRH CRL CBLHCT1 Manuel utilisateur

Emerson

Emerson Klauke ES 105CFM Manuel utilisateur

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Mode d’emploi

Danfoss

Danfoss ET4350 Manuel utilisateur

Milwaukee

Milwaukee M18 Manuel utilisateur

HOGERT

HOGERT HT1P169 Manuel utilisateur

Textron

Textron ESG105L Manuel utilisateur

Tyco Electronics

Tyco Electronics 90035-3 Manuel utilisateur

Emerson

Emerson Klauke ES 20RMCCFB Manuel utilisateur

Continental Refrigerator

Continental Refrigerator PC150HD Manuel utilisateur

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manuel utilisateur