TE Connectivity 58422-1 Manuel utilisateur
Instruction Sheet
1 of 6
© 2017 TE Connectivity Ltd. family of companies.
All Rights Reserved.
*Trademark
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.
PRODUCT INFORMATION
1-800-522-6752
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com.
408-9535
30 MAY 17 REV D
Figure 1
1. INTRODUCTION
This instruction sheet covers application, inspection and maintenance procedures for Crimping Heads 58422-1
and 2161730-11shown typically in Figure 1. The crimping heads use interchangeable crimping dies used to
crimp a variety of heavy-duty terminals and splices for large wire sizes (Size 8 thru 4/0 AWG) as listed in Figure
2. This instruction sheet provides general information for the insertion of dies and the crimping procedure.
Always refer to the instructions packaged with specific die sets for compatible products, wire ranges, strip
dimensions, and application procedures.
Products Crimped
AMPLI-BOND* and PLASTI-GRIP* Terminals
TERMINYL* Terminals and Splices
Pre-Insulated AMPOWER* Terminals
Pre-Insulated Nylon Heavy Duty Terminals
COPALUM* Sealed Terminals and Splices
Figure 2
This crimping heads are designed for two DYNA-CRIMP* tools: either Hydraulic Hand Pump 314979-1
described in Customer Manual 409-5860; or Hydraulic Power Unit 69120-[ ] described in Customer Manual
409-1950.
Warning: To avoid personal injury and potential damage to the crimp head, TE Connectivity (TE) requires the
crimp head to operate at 8,000 to 8,400 PSI [552 to 579 bar]. TE recommends using 8,200 PSI [565 bar] TE
Hydraulic Pumps as other manufacturers’ pumps may apply insufficient pressure (resulting in an inadequate
crimp) or excessive pressure (resulting in failure of the head). Additionally, the TE pump must be used to
maintain CE certification; if using other manufacturers’ pumps, the user is responsible for self-certification.
Read these instructions and other applicable references carefully before proceeding.
1Part Number 2161730-1 is a special version of PN 58422-1, with an extended stroke for terminating sealed COPALUM quick-termination connectors.
Hydraulic Crimping Heads
58422-1 and 2161730-1
408-9535
Rev D
2 of 6
NOTE
Dimensions in this instruction sheet are in millimeters [with inches in brackets]. Illustrations and figures are for reference only
and are not drawn to scale.
Reasons for reissue of this Instruction Sheet are provided in Section 8; REVISION SUMMARY.
2. DESCRIPTION
Main components of the crimping head are: a yoke which houses the stationary die and retains the terminal
assembly for crimping, a removable latch pin which allows pivoting of the yoke on the pivot pin (typically
required for splice terminations), a cylinder which contains the head’s hydraulic chamber, a piston (ram) which
holds and controls the moving die, and a quick connect/disconnect coupler (cylinder half) which mates with the
coupler on hose or handle control to release or supply pressure.
DANGER
To avoid injury when using DYNA-CRIMP equipment, observe the following precautions:
DO NOT modify the crimping equipment in any way.
USE ONLY dies, terminals, and wire specified for the head.
DO NOT perform repairs other than those specified in the instructional material supplied with the
equipment.
3. CRIMPING HEAD INSTALLATION
Each crimping head is shipped with a coating of lubricating oil to prevent rust and corrosion. Wipe the oil off
before installing the crimping head on the power unit. Note that the crimping head is shipped without oil inside
the cylinder. To install crimping head, proceed as follows:
DANGER
Verify that the hydraulic pressure to hose or handle control is released and that power supply is disconnected from electric
power unit, if applicable.
NOTE
If a coupling component for the hose assembly is packaged inside the quick connect/disconnect coupler on the head, it is to
be used to replace the coupling on a hose assembly not equipped with a quick connect/disconnect coupler.
1. Thoroughly clean coupling area of handle control or hose assembly and crimping head (see Figure 1).
2. Remove protective dust caps from both quick connect/disconnect couplers.
3. Hold hose or handle control in vertical position to prevent oil spillage. Attach hose or handle control to
coupling section on head. THREAD PROPERLY AND TIGHTEN SECURELY.
CAUTION
Oil flow must be unobstructed between power unit and crimping head. Verify that all couplers are fully mated and tightened.
NOTE
If crimping head must be removed after being in production, pressure must be released in the hydraulic system before head is
removed.
If using Hydraulic Power Unit 69120-[ ], disconnect power unit from power supply.
If using Hydraulic Hand Pump 314979-1, depress pressure release lever.
4. DIE INSERTION AND REMOVAL (FIGURE 3)
DANGER
Use extreme care when operating power unit. DO NOT inadvertently actuate the tool when installing or changing dies.
Personal injury could result.
NOTE
Make sure that matched die set, terminal and wire size are compatible.
With crimping head properly installed, refer to die set instructions, and insert/change die set as follows:
1. Remove latch pin and open yoke on crimping head.
408-9535
Rev D
3 of 6
Figure 3
2. Loosen setscrew in yoke. Refer to die set instructions and insert stationary (upper) die which includes
the nest area into well of yoke.
Tighten setscrew.
3. Activate power unit to advance ram until setscrew is visible (about 12.7 mm [.50 in.]).
Loosen setscrew.
4. Insert moving (lower) die (which serves as the indenter) into ram well, making sure that moving die is
properly oriented to mate with stationary die.
Tighten setscrew.
5. Close yoke and secure with latch pin.
6. Slowly close dies to ensure proper alignment
7. Complete the cycle and return the ram to the DOWN position
CAUTION
ALWAYS ensure that latch pin is fully inserted or damage may occur to yoke, dies, or latch pin.
5. CRIMPING PROCEDURE
The following crimping procedure provides general information. Refer to instructions packaged with individual
die sets for specific products, wire sizes, strip dimensions, positioning of terminals and splices in the dies, and
crimping procedures.
DANGER
To prevent personal injury when operating the power unit, exercise caution while holding terminals, splices or wire near
crimping area.
CAUTION
Never operate the power unit without having a crimping head attached to the handle control or crimping head coupling.
1. Insert terminal or splice in the stationary (upper) die in accordance with instructions packaged with the
dies. Verify the latch pin is secure before activating the power unit.
2. Slowly advance moving (lower) die with short, quick strokes until terminal or splice is secure.
3. Insert the stripped wire.
408-9535
Rev D
4 of 6
4. Cycle tool to complete the crimp. Remove crimped terminal or splice.
NOTE
If the splice or terminal sticks in the die after crimping, apply a rocking action to release it.
6. INSPECTION AND MAINTENANCE
DANGER
Verify hydraulic pressure is released and power supply is disconnected before following inspection and maintenance
procedures, unless otherwise specified in the procedure.
Each crimping head is assembled and inspected before shipment. TE Connectivity recommends that the
crimping head be inspected immediately upon its arrival at the facility of use, and at regularly scheduled
intervals, to ensure the head has not been damaged during handling and use. Frequency of inspection
depends upon the following: care, amount of use, and handling of the head; type and size of products crimped;
degree of operator skill; and environmental conditions.
6.1. Cleaning
Remove accumulations of dirt and grease on the crimping head; especially in areas where dies are installed
and terminals are crimped. Clean the entire head frequently with a clean, lint-free cloth.
6.2. Visual Inspection
Refer to Figure 4 and proceed as follows:
1. With hydraulic pressure released, inspect the assembled head for nicks, scratches, and cracks.
Inspect for cracks especially at the corners of the yoke and around the top of the cylinder.
Figure 4
2. Inspect pivot pin holes and latch pin holes for wear. Replace parts, as needed.
3. Activate power unit. Raise ram to “UP” position. Inspect flat and round surfaces of ram for galling
(fretting or wear by friction), cracks, or oil leakage.
Release pressure and make sure ram retracts smoothly.
408-9535
Rev D
5 of 6
4. If head shows evidence of galling, cracks, oil leakage, or rough cycling, return the crimping head to TE
for repairs. Refer to Section 7, REPLACEMENT AND REPAIR.
NOTE
Once per year, or every 7,500 cycles (whichever comes first), the hydraulic head should be returned to TE for magnetic
particle inspection. Additionally, inspect and service the head (as described in Figure 4) every month or 1,000 cycles. Refer
to Instruction Sheet 408-9684.
6.3. Crimping Head Check-Out Procedure
If the ram fails to return to the “DOWN” position after completion of a crimping cycle, the cause may be in the
crimping head. To determine whether the trouble is in the crimping head, or not, proceed as follows:
With Hydraulic Power Unit 69120-[ ]
With power unit activated, press the pressure release button on the electrical control box, or, if the unit has the
“dump” feature, move the trigger to the “dump” position and hold for several seconds. This will release any
pressure in the hydraulic system.
If the ram returns to the “DOWN” position, the trouble is NOT in the crimping head.
If ram does not return, ensure the coupler is fully engaged. If coupler is engaged and ram still does not go
DOWN, return the crimping head for repairs.
With Hydraulic Hand Pump 314979-1
With power unit activated, turn the HOLD/RETURN lever to the RETURN position.
If the ram fails to return to the “START” or “DOWN” position, return the crimping head for repairs.
7. REPLACEMENT AND REPAIR
Customer-replaceable parts are listed in Figure 5. A complete inventory should be stocked and controlled to
prevent lost time when replacement of parts is necessary. Order parts through your TE Representative or call
1-800-526-5142, or send a facsimile of your purchase order to 1-717-986-7605, or write, or return the entire
tool for evaluation and repair, with a written description of the problem to:
CUSTOMER SERVICE (38-35)
TE CONNECTIVITY CORPORATION
P.O. BOX 3608
HARRISBURG, PA 17105-3608
Tools may also be returned for evaluation and repair. For tool repair service, contact a TE Representative at
1-800-526-5136.
8. REVISION SUMMARY
Added Warning (paragraph 1)
Added NOTE after paragraph 6.2.4. specifying return to TE for magnetic particle inspection
408-9535
Rev D
6 of 6
Item
Number
Part Number
Description
Quantity
Per Head
1
311471-1
Coupler, Quick Connect / Disconnect
1
2
306209-8
Pin, Removable Latch
1
3
8-59558-5
Pin, Pivot
1
4
1-21045-1
Ring, Retaining
1
5
4-21012-0
Setscrew
3
6
4-23147-7
Spring, Compression
1
7
1-21919-6
Pin, Dowel
1
Figure 5
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels TE Connectivity Outils de sertissage
TE Connectivity
TE Connectivity 2391789-1 Manuel utilisateur
TE Connectivity
TE Connectivity SDE-SA Manuel utilisateur
TE Connectivity
TE Connectivity 2377672-1 Manuel utilisateur
TE Connectivity
TE Connectivity CERTI-CRIMP 90165-1 Manuel utilisateur
TE Connectivity
TE Connectivity AT-SC Manuel utilisateur
TE Connectivity
TE Connectivity MR-1 Manuel utilisateur
TE Connectivity
TE Connectivity 2063534-1 Manuel utilisateur
TE Connectivity
TE Connectivity SDE-SA PN 2063534-1 Manuel utilisateur
TE Connectivity
TE Connectivity PRO-CRIMPER III Manuel utilisateur
TE Connectivity
TE Connectivity 2063528-1 Manuel utilisateur
TE Connectivity
TE Connectivity 2392945-1 Manuel utilisateur
TE Connectivity
TE Connectivity HVA280-2P Manuel utilisateur
TE Connectivity
TE Connectivity 1213875 Series Manuel utilisateur
TE Connectivity
TE Connectivity 2217480 Series Guide de référence
TE Connectivity
TE Connectivity 607949-1 Manuel utilisateur
TE Connectivity
TE Connectivity SDE-SA Manuel utilisateur
TE Connectivity
TE Connectivity 1213890-1 Guide de référence
TE Connectivity
TE Connectivity 2392637-1 Manuel utilisateur
TE Connectivity
TE Connectivity 90281-1 Manuel utilisateur
TE Connectivity
TE Connectivity 69069 Manuel utilisateur
Manuels Outils de sertissage populaires d'autres marques
HOGERT
HOGERT HT1P169 Manuel utilisateur
Textron
Textron ESG105L Manuel utilisateur
Tyco Electronics
Tyco Electronics 90035-3 Manuel utilisateur
Emerson
Emerson Klauke ES 20RMCCFB Manuel utilisateur
Continental Refrigerator
Continental Refrigerator PC150HD Manuel utilisateur
Tyco Electronics
Tyco Electronics CERTI-CRIMP 90418-1 Manuel utilisateur